Step Action | Nortel Networks NN46205-310 guide

34Installation

Procedure steps

Step Action

1Use a Phillips screwdriver to loosen the two screws that fasten the filler panel to the chassis.

2Pull the filler panel away from the slot as shown in the following figure.

--End--

Installing an Ethernet Routing Switch 8003, 8006, or 8010 chassis into a rack

Install an Ethernet Routing Switch 8003, 8006, or 8010 chassis in a standard equipment rack (19-inch).

Prerequisites for installing an Ethernet Routing Switch 8003, 8006, or 8010 chassis into a rack

•Remove any filler panels before you install the chassis to decrease the weight during installation.

Procedure steps

Step Action

1Hold each rack-mounting bracket to the sides of the chassis, and align the screw holes.

Nortel Ethernet Routing Switch 8600

Quick Start

NN46205-310 02.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 34

Nortel Networks NN46205-310 quick start Step Action

Contents

Quick Start Legal Notice Contents Configuration International Regulatory Statements of Conformity Regulatory Information and Safety PrecautionsFCC Statement USA only EN 300386 Statement CE Marking Statement Europe only EN 55 022 StatementsEN 55 024 Statement EC Declaration of Conformity Vcci Statement Japan/Nippon only Bsmi Statement for 8010, 8006 and 8003 Chassis Taiwan only CE Marking Statement Europe only EN 60 950 Statement National Safety Statements of ComplianceNOM Statement 8010, 8006, and 8003 Chassis Mexico only National Safety Statements of Compliance Información NOM unicamente para México Denan Statement Japan/Nippon only Safety Messages ESD Attenzione ESD Avertissement Peligro Pericolo Regulatory Information and Safety Precautions Software license Nortel Networks Inc. software license agreement General Nortel Networks Inc. software license agreement Software license New in this release FeaturesNortel Command Line Interface Other changes Setting the system date and time using the CLI Connecting the modem using the CLIConnecting the modem using the Nncli Setting the system date and time using the Nncli Introduction Navigation Introduction Installation preparation Ethernet Routing Switch 8600 slots DC power supply accessories Personal safety Safety precautionsSafety precautions navigation Check Accessory Use to Module safety Cable and connector safety Electrostatic discharge safety Risk of equipment damage Installation preparation Installation Unpacking the chassis Removing a power ﬁller panel Procedure steps Step Action Risk of personal injury Installing the 8010co chassis in a 19-inch two-post rack Prerequisites Installing the 8003, 8006, and 8010 chassis cable guides Installing the top cable-management bracket Installing the side cable-management brackets Procedure job aid Installing the cable-management brackets Grounding the 8010co chassis Procedure job aid Grounding the 8010co chassis Installing a moduleLocation of ground studs on a 8010co chassis rear panel For instructions, see Removing a power filler panel Installing AC power modules Procedure job aid Installing a module Installing DC power modules Installing DC power modules Installation Installing DC power modules End Installing a Pcmcia software card Installing a breaker interface panelStarting the system Turning on DC power supplies Verifying a successful installation LED power supply Installation Connecting a modem using the CLI Conﬁguration Baud rate 8databits truefalse Mode asciislipppp Variable definitions Variable Value DCE DB-25 Connecting a modem using the NncliNumber Pin number Boot config sio modem Connecting a VT-100 terminal or PC for local access Procedure job aid config setdate command sample output Setting system date and time using the CLISetting system date and time using the Nncli Procedure job aid clock set command output Change a password by using the following command Info Oper username Configure password options by using the following command Variable definition Aging-time Conﬁguring the system using the setup utility Install Prompt Action Procedure job aid Setup Utility prompt descriptionsMaster slot 5/6 Tftp Vlan Risques de blessure corporelle Translation of safety messagesFan tray safety warning message Verletzungsrisiko Risco de ferimento Preventing back injury warning statementRischio di lesioni personali Preventing back injury warning statement Verletzungsrisiko durch Preventing electrical shock warning statementRisques de blessure par choc électrique Riesgo de lesiones por choques eléctricos Rischio di lesioni per shock elettrico Preventing hand injury warning statementRisco de ferimento por choque elétrico Risques de blessure provoquée par les pales du ventilateur Risco de ferimento com lâmina do ventilador Safety danger statementRiesgo de lesiones por las aspas del ventilador Rischio di lesioni causate dalle lame del ventilatore Injury to eye warning statement Risques de blessure oculaire par lumière laser Laser pode causar ferimentos no olho Risiko einer Augenverletzung durchRiesgo de lesión en los ojos por láser Rischio di ustioni agli occhi dovute al laser Safety practices and the hazards danger statement Riesgo de lesión por electrocución Risco de ferimentos por choque elétrico Rischio di scosse elettriche Pericolo Rischio di scosse elettriche Preventing electric shock danger statement Page Quick Start