Nortel Networks NN46205-310 specs

38Installation

Step Action

1Loosen, but do not remove, the rack-mounting screws required to install a cable guide.

2Slide the cable guide onto the loosened screws.

3Tighten the screws to secure the cable guide to the chassis.

--End--

Installing the top cable-management bracket

Install the top cable-management bracket to the 8010co chassis.

Procedure steps

Step Action

1Align the mounting retainers on the inside of the top cable-management bracket with the holes on the front of the chassis.

2Push the sides of the top cable-management bracket into place.

3Insert and tighten the eight screws using a Phillips screwdriver to secure the top cable-management bracket to the chassis.

--End--

Nortel Ethernet Routing Switch 8600

Quick Start

NN46205-310 02.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 38

Nortel Networks NN46205-310 quick start Installing the top cable-management bracket

Contents

Quick Start Legal Notice Contents Configuration FCC Statement USA only Regulatory Information and Safety PrecautionsInternational Regulatory Statements of Conformity EN 300386 Statement CE Marking Statement Europe only EN 55 022 StatementsEN 55 024 Statement EC Declaration of Conformity Vcci Statement Japan/Nippon only Bsmi Statement for 8010, 8006 and 8003 Chassis Taiwan only NOM Statement 8010, 8006, and 8003 Chassis Mexico only National Safety Statements of ComplianceCE Marking Statement Europe only EN 60 950 Statement National Safety Statements of Compliance Información NOM unicamente para México Denan Statement Japan/Nippon only Safety Messages ESD Attenzione ESD Avertissement Peligro Pericolo Regulatory Information and Safety Precautions Software license Nortel Networks Inc. software license agreement General Nortel Networks Inc. software license agreement Software license New in this release FeaturesNortel Command Line Interface Other changes Setting the system date and time using the CLI Connecting the modem using the CLIConnecting the modem using the Nncli Setting the system date and time using the Nncli Introduction Navigation Introduction Installation preparation Ethernet Routing Switch 8600 slots DC power supply accessories Personal safety Safety precautionsSafety precautions navigation Check Accessory Use to Module safety Cable and connector safety Electrostatic discharge safety Risk of equipment damage Installation preparation Installation Unpacking the chassis Removing a power ﬁller panel Procedure steps Step Action Risk of personal injury Installing the 8010co chassis in a 19-inch two-post rack Prerequisites Installing the 8003, 8006, and 8010 chassis cable guides Installing the top cable-management bracket Installing the side cable-management brackets Procedure job aid Installing the cable-management brackets Grounding the 8010co chassis Location of ground studs on a 8010co chassis rear panel Installing a moduleProcedure job aid Grounding the 8010co chassis For instructions, see Removing a power filler panel Installing AC power modules Procedure job aid Installing a module Installing DC power modules Installing DC power modules Installation Installing DC power modules End Starting the system Installing a breaker interface panelInstalling a Pcmcia software card Turning on DC power supplies Verifying a successful installation LED power supply Installation Connecting a modem using the CLI Conﬁguration Baud rate 8databits truefalse Mode asciislipppp Variable definitions Variable Value Number Pin number Connecting a modem using the NncliDCE DB-25 Boot config sio modem Connecting a VT-100 terminal or PC for local access Procedure job aid config setdate command sample output Setting system date and time using the CLISetting system date and time using the Nncli Procedure job aid clock set command output Change a password by using the following command Info Oper username Configure password options by using the following command Variable definition Aging-time Conﬁguring the system using the setup utility Install Master slot 5/6 Procedure job aid Setup Utility prompt descriptionsPrompt Action Tftp Vlan Risques de blessure corporelle Translation of safety messagesFan tray safety warning message Verletzungsrisiko Rischio di lesioni personali Preventing back injury warning statementRisco de ferimento Preventing back injury warning statement Verletzungsrisiko durch Preventing electrical shock warning statementRisques de blessure par choc électrique Riesgo de lesiones por choques eléctricos Rischio di lesioni per shock elettrico Preventing hand injury warning statementRisco de ferimento por choque elétrico Risques de blessure provoquée par les pales du ventilateur Risco de ferimento com lâmina do ventilador Safety danger statementRiesgo de lesiones por las aspas del ventilador Rischio di lesioni causate dalle lame del ventilatore Injury to eye warning statement Risques de blessure oculaire par lumière laser Laser pode causar ferimentos no olho Risiko einer Augenverletzung durchRiesgo de lesión en los ojos por láser Rischio di ustioni agli occhi dovute al laser Safety practices and the hazards danger statement Riesgo de lesión por electrocución Risco de ferimentos por choque elétrico Rischio di scosse elettriche Pericolo Rischio di scosse elettriche Preventing electric shock danger statement Page Quick Start