Manuals / Nortel Networks / Computer Equipment / Switch

Nortel Networks NN46205-310 quick start Installing DC power modules, Prerequisites

Models: NN46205-310

1 82

Download 82 pages 40.24 Kb

Page 44

44Installation

Prerequisites

Ensure the filler panel or cover from the power bay is removed. To remove the filler panel, see “Removing a power filler panel” (page 33).

Procedure steps

Step Action

1Grasp the handle of the new power supply and push the power supply firmly into the bay.

2Tighten the retaining screws until the power supply is firmly seated.

3Connect the power cord to the power supply and to an AC power outlet that is connected to a circuit with no other equipment connections.

--End--

Installing DC power modules

Install the DC power supply module in the leftmost bay to supply DC power to the chassis.

ATTENTION

The 8006 and 8010 chassis have three power supply bays that are numbered 1, 2, and 3 from left to right as viewed from the front of the chassis.

Prerequisites

•Verify that you have the following tools and materials:

—Cable

—Crimping tool for crimping the lugs onto the cable

—Heat gun to shrink the tubing around the cable (optional)

Nortel Ethernet Routing Switch 8600

Quick Start

NN46205-310 02.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 44

Nortel Networks NN46205-310 quick start Installing DC power modules, Prerequisites

Contents

Quick Start Legal Notice Contents Configuration FCC Statement USA only Regulatory Information and Safety PrecautionsInternational Regulatory Statements of Conformity CE Marking Statement Europe only EN 55 022 Statements EN 55 024 StatementEN 300386 Statement EC Declaration of ConformityVcci Statement Japan/Nippon only Bsmi Statement for 8010, 8006 and 8003 Chassis Taiwan onlyNOM Statement 8010, 8006, and 8003 Chassis Mexico only National Safety Statements of ComplianceCE Marking Statement Europe only EN 60 950 Statement National Safety Statements of Compliance Información NOM unicamente para MéxicoDenan Statement Japan/Nippon only Safety Messages ESDAttenzione ESD Avertissement Peligro Pericolo Regulatory Information and Safety Precautions Software license Nortel Networks Inc. software license agreementGeneral Nortel Networks Inc. software license agreement Software license Features Nortel Command Line InterfaceNew in this release Other changesConnecting the modem using the CLI Connecting the modem using the NncliSetting the system date and time using the CLI Setting the system date and time using the NncliIntroduction NavigationIntroduction Installation preparation Ethernet Routing Switch 8600 slotsDC power supply accessories Safety precautions Safety precautions navigationPersonal safety Check Accessory Use toModule safety Cable and connector safetyElectrostatic discharge safety Risk of equipment damageInstallation preparation Installation Unpacking the chassis Removing a power ﬁller panel Procedure stepsStep Action Risk of personal injury Installing the 8010co chassis in a 19-inch two-post rack PrerequisitesInstalling the 8003, 8006, and 8010 chassis cable guides Installing the top cable-management bracket Installing the side cable-management brackets Procedure job aid Installing the cable-management bracketsGrounding the 8010co chassis Location of ground studs on a 8010co chassis rear panel Installing a moduleProcedure job aid Grounding the 8010co chassis For instructions, see Removing a power filler panel Installing AC power modules Procedure job aid Installing a moduleInstalling DC power modules Installing DC power modules Installation Installing DC power modules End Starting the system Installing a breaker interface panelInstalling a Pcmcia software card Turning on DC power supplies Verifying a successful installation LED power supplyInstallation Connecting a modem using the CLI ConﬁgurationBaud rate 8databits truefalse Mode asciislipppp Variable definitions Variable ValueNumber Pin number Connecting a modem using the NncliDCE DB-25 Boot config sio modem Connecting a VT-100 terminal or PC for local access Setting system date and time using the CLI Setting system date and time using the NncliProcedure job aid config setdate command sample output Procedure job aid clock set command outputChange a password by using the following command Info Oper username Configure password options by using the following command Variable definitionAging-time Conﬁguring the system using the setup utility InstallMaster slot 5/6 Procedure job aid Setup Utility prompt descriptionsPrompt Action Tftp Vlan Translation of safety messages Fan tray safety warning messageRisques de blessure corporelle VerletzungsrisikoRischio di lesioni personali Preventing back injury warning statementRisco de ferimento Preventing back injury warning statement Preventing electrical shock warning statement Risques de blessure par choc électriqueVerletzungsrisiko durch Riesgo de lesiones por choques eléctricosPreventing hand injury warning statement Risco de ferimento por choque elétricoRischio di lesioni per shock elettrico Risques de blessure provoquée par les pales du ventilateurSafety danger statement Riesgo de lesiones por las aspas del ventiladorRisco de ferimento com lâmina do ventilador Rischio di lesioni causate dalle lame del ventilatoreInjury to eye warning statement Risques de blessure oculaire par lumière laserRisiko einer Augenverletzung durch Riesgo de lesión en los ojos por láserLaser pode causar ferimentos no olho Rischio di ustioni agli occhi dovute al laserSafety practices and the hazards danger statement Riesgo de lesión por electrocuciónRisco de ferimentos por choque elétrico Rischio di scosse elettrichePericolo Rischio di scosse elettriche Preventing electric shock danger statement Page Quick Start