Nortel Networks NN46205-310 specs

8Regulatory Information and Safety Precautions

National Safety Statements of Compliance

CE Marking Statement (Europe only)

EN 60 950 Statement

This is to certify that the Nortel 8000 Series chassis and components installed within the chassis are in compliance with the requirements of EN 60 950 in accordance with the Low Voltage Directive. Additional national differences for all European Union countries have been evaluated for compliance. Some components installed within the 8000 Series chassis may use a nickel-metal hydride (NiMH) and/or lithium-ion battery. The NiMH and lithium-ion batteries are long-life batteries, and it is very possible that you will never need to replace them. However, should you need to replace them, refer to the individual component manual for directions on replacement and disposal of the battery.

NOM Statement 8010, 8006, and 8003 Chassis (Mexico only)

The following information is provided on the devices described in this document in compliance with the safety requirements of the Norma Oficial Méxicana (NOM):

Exporter:

Importer:

Nortel Networks, Inc.

4655 Great America Parkway

Santa Clara CA 95054 USA

Nortel Networks de México, S.A. de C.V.

Avenida Insurgentes Sur #1605

Piso 30, Oficina

Col. San Jose Insurgentes

Deleg-Benito Juarez

Nortel Ethernet Routing Switch 8600

Quick Start

NN46205-310 02.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 8

Nortel Networks NN46205-310 National Safety Statements of Compliance, CE Marking Statement Europe only EN 60 950 Statement

Contents

Quick Start Legal Notice Contents Configuration FCC Statement USA only Regulatory Information and Safety PrecautionsInternational Regulatory Statements of Conformity CE Marking Statement Europe only EN 55 022 Statements EN 55 024 StatementEN 300386 Statement EC Declaration of Conformity Vcci Statement Japan/Nippon only Bsmi Statement for 8010, 8006 and 8003 Chassis Taiwan only NOM Statement 8010, 8006, and 8003 Chassis Mexico only National Safety Statements of ComplianceCE Marking Statement Europe only EN 60 950 Statement National Safety Statements of Compliance Información NOM unicamente para México Denan Statement Japan/Nippon only Safety Messages ESD Attenzione ESD Avertissement Peligro Pericolo Regulatory Information and Safety Precautions Software license Nortel Networks Inc. software license agreement General Nortel Networks Inc. software license agreement Software license Features Nortel Command Line InterfaceNew in this release Other changes Connecting the modem using the CLI Connecting the modem using the NncliSetting the system date and time using the CLI Setting the system date and time using the Nncli Introduction Navigation Introduction Installation preparation Ethernet Routing Switch 8600 slots DC power supply accessories Safety precautions Safety precautions navigationPersonal safety Check Accessory Use to Module safety Cable and connector safety Electrostatic discharge safety Risk of equipment damage Installation preparation Installation Unpacking the chassis Removing a power ﬁller panel Procedure steps Step Action Risk of personal injury Installing the 8010co chassis in a 19-inch two-post rack Prerequisites Installing the 8003, 8006, and 8010 chassis cable guides Installing the top cable-management bracket Installing the side cable-management brackets Procedure job aid Installing the cable-management brackets Grounding the 8010co chassis Location of ground studs on a 8010co chassis rear panel Installing a moduleProcedure job aid Grounding the 8010co chassis For instructions, see Removing a power filler panel Installing AC power modules Procedure job aid Installing a module Installing DC power modules Installing DC power modules Installation Installing DC power modules End Starting the system Installing a breaker interface panelInstalling a Pcmcia software card Turning on DC power supplies Verifying a successful installation LED power supply Installation Connecting a modem using the CLI Conﬁguration Baud rate 8databits truefalse Mode asciislipppp Variable definitions Variable Value Number Pin number Connecting a modem using the NncliDCE DB-25 Boot config sio modem Connecting a VT-100 terminal or PC for local access Setting system date and time using the CLI Setting system date and time using the NncliProcedure job aid config setdate command sample output Procedure job aid clock set command output Change a password by using the following command Info Oper username Configure password options by using the following command Variable definition Aging-time Conﬁguring the system using the setup utility Install Master slot 5/6 Procedure job aid Setup Utility prompt descriptionsPrompt Action Tftp Vlan Translation of safety messages Fan tray safety warning messageRisques de blessure corporelle Verletzungsrisiko Rischio di lesioni personali Preventing back injury warning statementRisco de ferimento Preventing back injury warning statement Preventing electrical shock warning statement Risques de blessure par choc électriqueVerletzungsrisiko durch Riesgo de lesiones por choques eléctricos Preventing hand injury warning statement Risco de ferimento por choque elétricoRischio di lesioni per shock elettrico Risques de blessure provoquée par les pales du ventilateur Safety danger statement Riesgo de lesiones por las aspas del ventiladorRisco de ferimento com lâmina do ventilador Rischio di lesioni causate dalle lame del ventilatore Injury to eye warning statement Risques de blessure oculaire par lumière laser Risiko einer Augenverletzung durch Riesgo de lesión en los ojos por láserLaser pode causar ferimentos no olho Rischio di ustioni agli occhi dovute al laser Safety practices and the hazards danger statement Riesgo de lesión por electrocución Risco de ferimentos por choque elétrico Rischio di scosse elettriche Pericolo Rischio di scosse elettriche Preventing electric shock danger statement Page Quick Start