Manuals / Nortel Networks / Computer Equipment / Switch

Nortel Networks NN46205-310 quick start Installing DC power modules

Models: NN46205-310

1 82

Download 82 pages 40.24 Kb

Page 45

Installing DC power modules 45

—A 7/16-inch hex wrench

—Phillips screwdriver

•Ensure the filler panel or cover is removed from the power bay. To remove the filler panel, see “Removing a power filler panel” (page 33).

ATTENTION

Nortel does not supply the cables for connecting the DC power supply to the DC input power source. Select cables that comply with the electrical code of the country where you use the DC power supply.

Procedure steps

Step Action

1Make sure that the power switch is turned off.

2Grasp the handle of the new power supply and push it partway into the bay, leaving the terminal block at the side of the power supply exposed.

3Remove the screw that secures the plastic safety cover to the power supply using a Phillips screwdriver.

4Remove the cover and set it aside.

5Record the positions of the ground stud and of the positive and negative power inputs.

ATTENTION

Make sure the +DC cable is always connected to the positive terminal and that the -DC cable is always connected to the negative terminal.

DANGER

Risk of injury by electric shock

Make sure that the DC power source is off by switching off the circuit breaker or disconnecting at the remote end before you connect the terminal leads to the power supply.

Nortel Ethernet Routing Switch 8600

Quick Start

NN46205-310 02.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 45

Nortel Networks NN46205-310 quick start Installing DC power modules

Contents

Quick Start Legal Notice Contents Configuration Regulatory Information and Safety Precautions International Regulatory Statements of ConformityFCC Statement USA only EN 55 024 Statement CE Marking Statement Europe only EN 55 022 StatementsEN 300386 Statement EC Declaration of ConformityBsmi Statement for 8010, 8006 and 8003 Chassis Taiwan only Vcci Statement Japan/Nippon onlyNational Safety Statements of Compliance CE Marking Statement Europe only EN 60 950 StatementNOM Statement 8010, 8006, and 8003 Chassis Mexico only Información NOM unicamente para México National Safety Statements of ComplianceDenan Statement Japan/Nippon only ESD Safety MessagesAttenzione ESD Avertissement Peligro Pericolo Regulatory Information and Safety Precautions Nortel Networks Inc. software license agreement Software licenseGeneral Nortel Networks Inc. software license agreement Software license Nortel Command Line Interface FeaturesNew in this release Other changesConnecting the modem using the Nncli Connecting the modem using the CLISetting the system date and time using the CLI Setting the system date and time using the NncliNavigation IntroductionIntroduction Ethernet Routing Switch 8600 slots Installation preparationDC power supply accessories Safety precautions navigation Safety precautionsPersonal safety Check Accessory Use toCable and connector safety Module safetyRisk of equipment damage Electrostatic discharge safetyInstallation preparation Installation Unpacking the chassis Procedure steps Removing a power ﬁller panelStep Action Risk of personal injury Prerequisites Installing the 8010co chassis in a 19-inch two-post rackInstalling the 8003, 8006, and 8010 chassis cable guides Installing the top cable-management bracket Procedure job aid Installing the cable-management brackets Installing the side cable-management bracketsGrounding the 8010co chassis Installing a module Procedure job aid Grounding the 8010co chassisLocation of ground studs on a 8010co chassis rear panel For instructions, see Removing a power filler panel Procedure job aid Installing a module Installing AC power modulesInstalling DC power modules Installing DC power modules Installation Installing DC power modules End Installing a breaker interface panel Installing a Pcmcia software cardStarting the system Turning on DC power supplies LED power supply Verifying a successful installationInstallation Conﬁguration Connecting a modem using the CLIBaud rate 8databits truefalse Mode asciislipppp Variable Value Variable definitionsConnecting a modem using the Nncli DCE DB-25Number Pin number Boot config sio modem Connecting a VT-100 terminal or PC for local access Setting system date and time using the Nncli Setting system date and time using the CLIProcedure job aid config setdate command sample output Procedure job aid clock set command outputChange a password by using the following command Info Oper username Variable definition Configure password options by using the following commandAging-time Install Conﬁguring the system using the setup utilityProcedure job aid Setup Utility prompt descriptions Prompt ActionMaster slot 5/6 Tftp Vlan Fan tray safety warning message Translation of safety messagesRisques de blessure corporelle VerletzungsrisikoPreventing back injury warning statement Risco de ferimentoRischio di lesioni personali Preventing back injury warning statement Risques de blessure par choc électrique Preventing electrical shock warning statementVerletzungsrisiko durch Riesgo de lesiones por choques eléctricosRisco de ferimento por choque elétrico Preventing hand injury warning statementRischio di lesioni per shock elettrico Risques de blessure provoquée par les pales du ventilateurRiesgo de lesiones por las aspas del ventilador Safety danger statementRisco de ferimento com lâmina do ventilador Rischio di lesioni causate dalle lame del ventilatoreRisques de blessure oculaire par lumière laser Injury to eye warning statementRiesgo de lesión en los ojos por láser Risiko einer Augenverletzung durchLaser pode causar ferimentos no olho Rischio di ustioni agli occhi dovute al laserRiesgo de lesión por electrocución Safety practices and the hazards danger statementRischio di scosse elettriche Risco de ferimentos por choque elétricoPericolo Rischio di scosse elettriche Preventing electric shock danger statement Page Quick Start