Installation, Navigation | Nortel Networks NN46205-310 instruction

.

31

Installation

This chapter contains installation instructions for the Ethernet Routing Switch 8000 series chassis.

Navigation

•“Unpacking the chassis” (page 32)

•“Removing a power filler panel” (page 33)

•“Installing an Ethernet Routing Switch 8003, 8006, or 8010 chassis into a rack” (page 34)

•“Installing the 8010co chassis in a 19-inchtwo-post rack” (page 36)

•“Installing the 8003, 8006, and 8010 chassis cable guides” (page 37)

•“Installing the top cable-management bracket” (page 38)

•“Installing the side cable-management brackets” (page 39)

•“Grounding the 8010co chassis” (page 40)

•“Installing a module” (page 41)

•“Installing AC power modules” (page 43)

•“Installing DC power modules” (page 44)

•“Installing a breaker interface panel” (page 49)

•“Installing a PCMCIA software card” (page 49)

•“Starting the system” (page 49)

•“Verifying a successful installation” (page 51)

Nortel Ethernet Routing Switch 8600

Quick Start

NN46205-310 02.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 31

Nortel Networks NN46205-310 quick start Installation, Navigation

Contents

Quick Start Legal Notice Contents Configuration International Regulatory Statements of Conformity Regulatory Information and Safety PrecautionsFCC Statement USA only EC Declaration of Conformity CE Marking Statement Europe only EN 55 022 StatementsEN 55 024 Statement EN 300386 Statement Bsmi Statement for 8010, 8006 and 8003 Chassis Taiwan only Vcci Statement Japan/Nippon only CE Marking Statement Europe only EN 60 950 Statement National Safety Statements of ComplianceNOM Statement 8010, 8006, and 8003 Chassis Mexico only Información NOM unicamente para México National Safety Statements of Compliance Denan Statement Japan/Nippon only ESD Safety Messages Attenzione ESD Avertissement Peligro Pericolo Regulatory Information and Safety Precautions Nortel Networks Inc. software license agreement Software license General Nortel Networks Inc. software license agreement Software license Other changes FeaturesNortel Command Line Interface New in this release Setting the system date and time using the Nncli Connecting the modem using the CLIConnecting the modem using the Nncli Setting the system date and time using the CLI Navigation Introduction Introduction Ethernet Routing Switch 8600 slots Installation preparation DC power supply accessories Check Accessory Use to Safety precautionsSafety precautions navigation Personal safety Cable and connector safety Module safety Risk of equipment damage Electrostatic discharge safety Installation preparation Installation Unpacking the chassis Procedure steps Removing a power ﬁller panel Step Action Risk of personal injury Prerequisites Installing the 8010co chassis in a 19-inch two-post rack Installing the 8003, 8006, and 8010 chassis cable guides Installing the top cable-management bracket Procedure job aid Installing the cable-management brackets Installing the side cable-management brackets Grounding the 8010co chassis Procedure job aid Grounding the 8010co chassis Installing a moduleLocation of ground studs on a 8010co chassis rear panel For instructions, see Removing a power filler panel Procedure job aid Installing a module Installing AC power modules Installing DC power modules Installing DC power modules Installation Installing DC power modules End Installing a Pcmcia software card Installing a breaker interface panelStarting the system Turning on DC power supplies LED power supply Verifying a successful installation Installation Conﬁguration Connecting a modem using the CLI Baud rate 8databits truefalse Mode asciislipppp Variable Value Variable definitions DCE DB-25 Connecting a modem using the NncliNumber Pin number Boot config sio modem Connecting a VT-100 terminal or PC for local access Procedure job aid clock set command output Setting system date and time using the CLISetting system date and time using the Nncli Procedure job aid config setdate command sample output Change a password by using the following command Info Oper username Variable definition Configure password options by using the following command Aging-time Install Conﬁguring the system using the setup utility Prompt Action Procedure job aid Setup Utility prompt descriptionsMaster slot 5/6 Tftp Vlan Verletzungsrisiko Translation of safety messagesFan tray safety warning message Risques de blessure corporelle Risco de ferimento Preventing back injury warning statementRischio di lesioni personali Preventing back injury warning statement Riesgo de lesiones por choques eléctricos Preventing electrical shock warning statementRisques de blessure par choc électrique Verletzungsrisiko durch Risques de blessure provoquée par les pales du ventilateur Preventing hand injury warning statementRisco de ferimento por choque elétrico Rischio di lesioni per shock elettrico Rischio di lesioni causate dalle lame del ventilatore Safety danger statementRiesgo de lesiones por las aspas del ventilador Risco de ferimento com lâmina do ventilador Risques de blessure oculaire par lumière laser Injury to eye warning statement Rischio di ustioni agli occhi dovute al laser Risiko einer Augenverletzung durchRiesgo de lesión en los ojos por láser Laser pode causar ferimentos no olho Riesgo de lesión por electrocución Safety practices and the hazards danger statement Rischio di scosse elettriche Risco de ferimentos por choque elétrico Pericolo Rischio di scosse elettriche Preventing electric shock danger statement Page Quick Start