Manuals / Nortel Networks / Computer Equipment / Switch

Nortel Networks NN46205-310 quick start Installing the 8003, 8006, and 8010 chassis cable guides

Models: NN46205-310

1 82

Download 82 pages 40.24 Kb

Page 37

Installing the 8003, 8006, and 8010 chassis cable guides 37

4Add a hex nut to each screw and tighten using a hex wrench.

5Tighten each screw using a Phillips-head screwdriver.

6If the holes in the rack vertical supports require clip nuts, insert a clip nut into each of the 12 locations.

7Lift the 8010co chassis onto the installation shelf.

WARNING

Risk of personal injury

It requires three people to lift the 8010co chassis. To make the chassis lighter, remove the modules and power supplies before you lift it.

8Hold the 8010co chassis in position and align the flanged end of the chassis mounting rail with the six holes on each side of the vertical rack support.

Make sure the hole pairs on each side of the vertical support match horizontally.

9Tighten each screw using a Phillips-head screwdriver.

--End--

Installing the 8003, 8006, and 8010 chassis cable guides

Install the 8003, 8006, and 8010 chassis cable guides to fasten the cable clusters and keep them out of the way.

ATTENTION

Ensure the cable clusters are accessible for maintenance.

Procedure steps

Nortel Ethernet Routing Switch 8600

Quick Start

NN46205-310 02.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 37

Nortel Networks NN46205-310 quick start Installing the 8003, 8006, and 8010 chassis cable guides

Contents

Quick Start Legal Notice Contents Configuration International Regulatory Statements of Conformity Regulatory Information and Safety PrecautionsFCC Statement USA only EN 55 024 Statement CE Marking Statement Europe only EN 55 022 StatementsEN 300386 Statement EC Declaration of ConformityBsmi Statement for 8010, 8006 and 8003 Chassis Taiwan only Vcci Statement Japan/Nippon onlyCE Marking Statement Europe only EN 60 950 Statement National Safety Statements of ComplianceNOM Statement 8010, 8006, and 8003 Chassis Mexico only Información NOM unicamente para México National Safety Statements of ComplianceDenan Statement Japan/Nippon only ESD Safety MessagesAttenzione ESD Avertissement Peligro Pericolo Regulatory Information and Safety Precautions Nortel Networks Inc. software license agreement Software licenseGeneral Nortel Networks Inc. software license agreement Software license Nortel Command Line Interface FeaturesNew in this release Other changesConnecting the modem using the Nncli Connecting the modem using the CLISetting the system date and time using the CLI Setting the system date and time using the NncliNavigation IntroductionIntroduction Ethernet Routing Switch 8600 slots Installation preparationDC power supply accessories Safety precautions navigation Safety precautionsPersonal safety Check Accessory Use toCable and connector safety Module safetyRisk of equipment damage Electrostatic discharge safetyInstallation preparation Installation Unpacking the chassis Procedure steps Removing a power ﬁller panelStep Action Risk of personal injury Prerequisites Installing the 8010co chassis in a 19-inch two-post rackInstalling the 8003, 8006, and 8010 chassis cable guides Installing the top cable-management bracket Procedure job aid Installing the cable-management brackets Installing the side cable-management bracketsGrounding the 8010co chassis Procedure job aid Grounding the 8010co chassis Installing a moduleLocation of ground studs on a 8010co chassis rear panel For instructions, see Removing a power filler panel Procedure job aid Installing a module Installing AC power modulesInstalling DC power modules Installing DC power modules Installation Installing DC power modules End Installing a Pcmcia software card Installing a breaker interface panelStarting the system Turning on DC power supplies LED power supply Verifying a successful installationInstallation Conﬁguration Connecting a modem using the CLIBaud rate 8databits truefalse Mode asciislipppp Variable Value Variable definitionsDCE DB-25 Connecting a modem using the NncliNumber Pin number Boot config sio modem Connecting a VT-100 terminal or PC for local access Setting system date and time using the Nncli Setting system date and time using the CLIProcedure job aid config setdate command sample output Procedure job aid clock set command outputChange a password by using the following command Info Oper username Variable definition Configure password options by using the following commandAging-time Install Conﬁguring the system using the setup utilityPrompt Action Procedure job aid Setup Utility prompt descriptionsMaster slot 5/6 Tftp Vlan Fan tray safety warning message Translation of safety messagesRisques de blessure corporelle VerletzungsrisikoRisco de ferimento Preventing back injury warning statementRischio di lesioni personali Preventing back injury warning statement Risques de blessure par choc électrique Preventing electrical shock warning statementVerletzungsrisiko durch Riesgo de lesiones por choques eléctricosRisco de ferimento por choque elétrico Preventing hand injury warning statementRischio di lesioni per shock elettrico Risques de blessure provoquée par les pales du ventilateurRiesgo de lesiones por las aspas del ventilador Safety danger statementRisco de ferimento com lâmina do ventilador Rischio di lesioni causate dalle lame del ventilatoreRisques de blessure oculaire par lumière laser Injury to eye warning statementRiesgo de lesión en los ojos por láser Risiko einer Augenverletzung durchLaser pode causar ferimentos no olho Rischio di ustioni agli occhi dovute al laserRiesgo de lesión por electrocución Safety practices and the hazards danger statementRischio di scosse elettriche Risco de ferimentos por choque elétricoPericolo Rischio di scosse elettriche Preventing electric shock danger statement Page Quick Start