5. P2 Card Fully Recorded
Display window | All 7 bar indicators for remaining MEDIA | |
indication | capacity start blinking. | |
|
| |
WARNING lamp | This lamp will illuminate continuously until an | |
operation is made after recording. | ||
| ||
|
| |
Tally lamp | This lamp will flash 4 times every second | |
until an operation is made after recording. | ||
| ||
|
| |
Viewfinder | The END indicator blinks. | |
|
| |
Warning tone | This tone will sound continuously until an | |
operation is made after recording. | ||
| ||
|
| |
Warning | The P2 cards are recorded to maximum | |
description | capacity. | |
|
| |
Recording/ |
| |
playback | The recording stops. | |
operation |
| |
|
| |
Countermeasures | Delete the clips in the P2 card or insert a | |
| new P2 card. |
7. Recording Error
| “00:00:00:11” appears in the time code | |
Display window | display field. Even after recording is stopped, | |
indication | this display continues to blink until the next | |
| operation is performed. | |
|
| |
WARNING lamp | Blinks 4 times per second while recording | |
continues. | ||
| ||
|
| |
Tally lamp | Blinks 4 times per second while recording | |
continues. | ||
| ||
|
| |
Viewfinder | The REC WARNING indicator lights up. | |
|
| |
Warning tone | Beeps 4 times per second while recording | |
continues. | ||
| ||
|
| |
| This indicates a failure either in the P2 card | |
Warning | recording or the recording circuit. This is | |
displayed when attempting to record clips | ||
description | ||
where the total quantity exceeds the upper | ||
| ||
| limit (1000 pieces) for a single P2 card. | |
|
| |
Recording/ | The recording may stop or continue. | |
playback |
| |
operation |
| |
|
| |
| Restart recording. Or, turn the power OFF | |
Countermeasures | and turn it ON again, before starting | |
| recording. | |
|
|
6.Image Sequence Error (24P, 30P, 25P)
Display window | ||
indication |
| |
|
| |
WARNING lamp | Blinks 4 times per second. | |
|
| |
Tally lamp | Blinks 4 times per second while recording | |
continues. | ||
| ||
|
| |
Viewfinder | The REC WARNING indicator lights up. | |
|
| |
Warning tone | Beeps 4 times per second while recording | |
continues. | ||
| ||
|
| |
Warning | There are abnormal conditions in the image | |
description | sequence of the 24P, 30P, or 25P mode. | |
|
| |
Recording/ | Images can be recorded and played back, | |
playback | but some frames may be dropped or the | |
operation | sequences of TC and UB may shift. | |
|
| |
| Confirm the recording/playback operation after | |
| turning OFF the power supply once and then | |
Countermeasures | turning it on again. If the error is not corrected | |
| after executing this procedure, contact the | |
| dealer. | |
|
|
8. Low Wireless Signal Reception
Display window | No display. | |
indication | ||
| ||
|
| |
WARNING lamp | Blinks 4 times per second. (During pause | |
and recording) | ||
| ||
|
| |
Tally lamp | Blinks 4 times per second while recording | |
continues. | ||
| ||
|
| |
Viewfinder | The WIRELESS RF indicator lights up while | |
recording continues. | ||
| ||
|
| |
Warning tone | Beeps 4 times per second while recording | |
continues. | ||
| ||
|
| |
Warning | This error indicates poor wireless audio | |
description | reception conditions. | |
|
| |
Recording/ | Continues to operate without receiving the | |
playback | ||
wireless microphone signal. | ||
operation | ||
| ||
|
| |
Countermeasures | Check the microphone power supply and the | |
| reception status of the wireless receiver. |
146 Maintenance and Inspections : Warning System