VF MARKER

 

Items/

Adjustable

 

 

 

Remarks

Data Saved

Range

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TABLE

A

Select the VF MARKER setting table.

 

 

 

 

 

B

First, select table A or B, then set the

–

C

U

F

R

 

items below for each table.

 

 

 

 

 

 

 

 

 

 

 

CENTER

OFF

Switch the center mark.

MARK

1

OFF: Do not display center mark.

 

 

 

 

 

2

1:

+ (large)

 

 

 

 

 

3

2:

Hollow (large)

 

 

 

 

 

3:

+ (small)

 

 

 

 

 

4

 

 

 

 

 

4:

Hollow (small)

–

C

U

F

R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SAFETY

OFF

Select the frame type for the safety

MARK

1

zone.

 

 

 

 

 

2

OFF: Do not display frame.

 

 

 

 

 

 

1:

Box

 

 

 

 

 

 

2:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Corner frame

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

–

C

U

F

R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SAFETY

80%

For setting the size of the safety marker.

AREA

:

It is possible to set the size by units of

 

 

 

 

 

90%

1% with a fixed ratio between of width

 

 

 

 

 

:

 

 

 

 

 

and height.

–

C

U

F

R

100%

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FRAME MARK

ON

Set the frame marker to ON or OFF.

 

 

 

 

 

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

–

C

U

F

R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FRAME SIG

4:3

Set the frame marker.

 

 

 

 

 

13:9

Only enabled when REC MODE is set to

 

 

 

 

 

14:9

16:9.

 

 

 

 

–

C

U

F

R

VISTA

The VISTA ratio is 16:8.65.

 

 

 

 

 

 

 

 

 

 

 

FRAME LVL

0

Set the level outside the frame marker.

 

 

 

 

 

:

0: Equivalent to signal OFF. （Blanking

 

 

 

 

 

15

 

status）

 

 

 

 

 

 

15: Same brightness as center area. This

 

 

 

 

 

 

 

setting, however, is disabled if the

–

C

U

F

R

 

 

 

 

FRAME SIG is set to VISTA.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

‹Note

When SYSTEM MODE is set to either “1080-59.94i”, “1080-50i”, “720-59.94P”, or “720-50P” (in HD mode), the safety zone marker, the safety zone area, and the frame marker are displayed on the LCD monitor or the SD viewfinder if “LT-BOX” or “S-CROP” is selected in

DOWNCON MODE.

VF USER BOX

 

Items/

Adjustable

Remarks

Data Saved

Range

 

 

 

 

USER BOX

ON

For setting whether the user box is

 

 

 

 

 

OFF

displayed in the viewfinder or not.

–

C

U

F

R

 

 

 

 

 

 

 

 

 

USER BOX

1

For setting the horizontal width of the

WIDTH

:

user box.

 

 

 

 

 

13

 

 

 

 

 

 

:

 

–

C

U

F

R

100

 

 

 

 

 

 

 

 

USER BOX

1

For setting the horizontal position of the

HEIGHT

:

user box center.

 

 

 

 

 

13

 

 

 

 

 

 

:

 

–

C

U

F

R

100

 

 

 

 

 

 

 

 

USER BOX H

–50

For setting the horizontal position of the

POS

:

user box center.

 

 

 

 

 

+00

 

 

 

 

 

 

:

 

–

C

U

F

R

+50

 

 

 

 

 

 

 

 

USER BOX V

–50

For setting the vertical position of the

POS

:

user box center.

 

 

 

 

 

+00

 

 

 

 

 

 

:

 

–

C

U

F

R

+50

 

 

 

 

 

 

 

 

zThe user box can be displayed in any position as a boxtype cursor.

‹Note

When SYSTEM MODE item is set to either “1080-59.94i”, “1080-50i”, “720-59.94P”, or “720-50P” (in HD mode), the user box is not displayed on the LCD monitor or the SD viewfinder if “LT-BOX” or “S-CROP” is selected in

DOWNCON MODE.

The ____ in the Adjustable Range column indicates the preset mode.

170 Menu : Menu Description Tables