9. 1394 Error
Display window | The 1394 | |
window blinks. For more information, see | ||
indication | ||
| ||
|
| |
WARNING lamp | Blinks 4 times per second while the | |
WARNING lamp recording is continuing. | ||
| ||
|
| |
Tally lamp | Blinks 4 times per second while the TALLY | |
LAMP recording is continuing. | ||
| ||
|
| |
| In the case of Error Code 92, “1394 INITIAL | |
| ERROR” indicator lights up (during pause | |
Viewfinder | and recording) | |
For Error Codes other than Error Code 92, or | ||
| ||
| if REC SIGNAL is set to “1394”, no error is | |
| displayed in the viewfinder. | |
|
| |
Warning tone | Beeps 4 times per second while ALARM | |
recording is continuing. | ||
| ||
|
| |
Warning | This indicates a failure of the DVCPRO/DV | |
description | connector. | |
|
| |
Recording/ | The operation continues, but input signals to | |
the DVCPRO/DV connector are abnormal. | ||
playback | ||
For more information, see [1394 Error | ||
operation | ||
|
Check the connection between the IEEE1394 cable and the DVCPRO/DV connector, settings of any external device
Countermeasures and menus, and the turn on the power again. If the warning indication is still illuminated, confirm the “1394 Error Codes” (page 148), and consult your distributor.
12. P2 Card Error
| If the error occurs during recording, | |
| “00:0000:11” appears as the time code | |
Display window | indication. The indication continues to flash | |
indication | after recording is stopped and until the next | |
| operation is performed. There is no | |
| indication if the error occurs during playback. | |
|
| |
| If the error occurs during recording, the lamp | |
WARNING lamp | flashes four times per second for a period of | |
about three seconds. The lamp does not | ||
| ||
| light if the error occurs during playback. | |
|
| |
| If the error occurs during recording, the lamp | |
Tally lamp | flashes four times per second for a period of | |
about three seconds. The lamp does not | ||
| ||
| light if the error occurs during playback. | |
|
| |
| A flashing “CARD ERR ¢” appears. In the | |
Viewfinder | actual indication the ¢ is replaced by the slot | |
| number of the P2 card that triggered the error. | |
|
| |
| If the error occurs during recording, the tone | |
Warning tone | sounds four times per second for a period of | |
about three seconds. The tone does not | ||
| ||
| sound if the error occurs during playback. | |
|
| |
Warning | An error has occurred while recording data | |
description | to or playing data from a P2 card. | |
|
| |
Recording/ |
| |
playback | Stop recording or playback. | |
operation |
| |
|
| |
Countermeasures | Replace the affected P2 card. | |
|
|
and Maintenance
10. Battery Nearly Empty
Display window | One of the bars in the battery remaining | |
indication | indicator starts blinking. | |
|
| |
WARNING lamp | Blinks once per second. | |
|
| |
Tally lamp | Blinks once per second. | |
|
| |
Viewfinder | The BATT LED blinks. | |
|
| |
Warning tone | Beeps 4 times per second. | |
|
| |
Warning | The battery is about to run out. | |
description | ||
| ||
|
| |
Recording/ |
| |
playback | Continues to operate. | |
operation |
|
Countermeasures Replace the battery as required.
11. P2 Card Nearly Full
Display window | One of the bars for remaining MEDIA | |
indication | capacity starts blinking. | |
|
| |
WARNING lamp | Blinks once per second while recording | |
continues. | ||
| ||
|
| |
Tally lamp | Blinks once per second while recording | |
continues. | ||
| ||
|
| |
Viewfinder | The P2 card remaining capacity indicator blinks. | |
|
| |
Warning tone | Beeps once per second while recording | |
continues. | ||
| ||
|
| |
Warning | The total remaining capacity of all the P2 | |
description | cards is two minutes or less. | |
|
| |
Recording/ |
| |
playback | Continues to operate. | |
operation |
| |
|
| |
Countermeasures | Replace the cards. If there is an empty card | |
| slot, insert a new card. |
13. FAN STOP
Display window | No display. | |
indication |
| |
|
| |
WARNING lamp | Blinks 4 times per second. | |
|
| |
Tally lamp | No display. | |
|
| |
Viewfinder | The FAN STOP indicator blinks while | |
recording continues. | ||
| ||
|
| |
Warning tone | It does not sound. | |
|
| |
Warning | The fan is at rest because something is | |
description | wrong with it. | |
|
| |
| If the | |
Recording/ | stopped, then the temperature inside rises. | |
playback | While the | |
operation | operate, clips may not be recorded or played | |
| back properly. | |
|
| |
Countermeasures | Immediately stop using the | |
| and consult your distributor. |
Inspections
Maintenance and Inspections : Warning System 147