Panasonic AJ-HPX2000 Card Warning Code, Warning and Error Display for Thumbnail Operation and USB HOST MODE

Card Warning Code

Code No.	Description	Recording	Indication in display
			window
	The directory organization on the inserted P2	Although different kinds of recording
E-70	card does not comply with the standards. ([DIR	operations will function, data may not be
	NG CARD (Slot No.)] is indicated on the	recorded properly. Use the unit to format the	A warning code blinks once
	viewfinder.)	card immediately.	every 2 seconds on the time
			code display section of the
	A P2 card was inserted where the number of	Although different kinds of recording
E-71	rewrites exceeds the limit of the standards.	operations will function, data may not be	display window.
	([RUN DOWN CARD (Slot No.)] is indicated on	recorded properly. It is recommended to
	the viewfinder.)	replace it.

Warning and Error Display for Thumbnail Operation and USB HOST MODE

Item	Message	Description	Measure
	CANNOT ACCESS!	Data cannot be accessed because it is	Restore media and clips to normal state before
		corrupted or for other reasons.	access.
	WRITE	The P2 or SD card is write protected.	Insert write-enabled media.
	PROTECTED!
	CARD FULL!	The P2 or SD card is full.	Insert media with sufficient capacity.
	NO CARD!	No P2 or SD card is inserted.	Insert compatible media.
	NO FILE!	The designated file is not found.	Check the file.
	CANNOT COPY!	Images cannot be copied.	Check the conditions for copying.
	CANNOT DELETE !	Contents version mismatch prevents	Match devices and contents version.
		deletion.
	UNKNOWN	Warning displayed to indicate contents	Match devices and contents version.
	CONTENTS	version mismatch.
	FORMAT!
	CANNOT FORMAT!	P2 card problem prevents formatting.	Check P2 card.
	CANNOT REPAIR!	Data cannot be repaired since content that	Check selected content.
		cannot be repaired is selected.
	CANNOT RE-	A clip that does not span multiple P2 cards	Check selected content.
	CONNECT!	cannot be reconnected.
	INVALID VALUE!	Entered data was invalid.	Enter data in a valid range.
	UNKNOWN DATA!	The metadata character code is invalid.	Use UTF-8 for the metadata character code. Use
Thumbnails			the viewer to enter correct characters.
	CANNOT REPAIR IN	Some of the selected clip could not be
	SELECTION!	repaired.
	NO SD CARD!	No SD card is inserted.	Insert an SD card.
	NO COPY TO SAME	A clip cannot be copied to the card storing	Copy the selected clip to a card that does not
	CARD!	the original clip.	contain the original clip.
	SAME CLIP IS	The clip cannot be copied because a clip that	Confirm the selected clip and release either the
	SELECTED!	has already been copied and the original clip	source clip or the destination clip and then execute
		have been selected.	the copy operation.
	USER CLIP NAME	Characters in the clip name had to be	The user clip name plus the counter value can only
	MODIFIED!	deleted in adding the counter value.	contain up to 100 bytes. Characters in the clip
			name are automatically deleted when the total
			exceeds 100 bytes.
	TOO MANY CLIPS!	Too many clips are selected.	Reduce the number of selected clips.
	LACK OF REC	There is not enough recording capacity left	Insert a card with sufficient recording capacity.
	CAPACITY!	on the card.
	CANNOT CHANGE!	Any thumbnails that cannot be produced on	Install the AVC-Intra codec board (AJ-YBX200G,
		the AVC-Intra 100 or AVC-Intra 50 and	optional) and set SYSTEM MODE according to the
		displayed in gray cannot be changed at the	clips.
		text memo position.
	MISSING CLIP!	A shot mark will be added to the clips recorded	Insert all P2 cards with recorded clips, and confirm
		on multiple P2 cards when all P2 cards are not	that the incomplete clip indicators disappear, and
		inserted yet.	then add shot marks.

Inspections and Maintenance

Maintenance and Inspections : Warning System 149