Panasonic AJ-HPX2000 manual 74

Information Item		Indication	Status
13. System information	SYSTEM ERROR-¢¢		Something abnormal is happening to the internal computer communications
and warnings			or reference signal. No further recording or playback can be performed. ¢¢
			is replaced with an error code.For more information, see [Error Codes]
			(page 148).
	TURN POWER OFF		P2 card has been removed while being accessed (recorded, played back, or
			formatted), and subsequent operation is disabled.
	CARD ERR ¢		An error has occurred while recording data to or playing data from a P2
			card. In the actual indication the ¢ is replaced by the slot number of the P2
			card that triggered the error.
	REC WARNING		Something abnormal is happening to video and/or audio being recorded.
	BACKUP BATT EMPTY		Backup battery needs replacing.
	FAN STOP		The fan is locked and halted.
	WIRELESS-RF		RF signal from the wireless receiver is degraded.
	EOM		P2 card has no free space.
	BOS		Playback position is at the start of all the clips.
	EOS		Playback position is at the end of all the clips.
	CANNOT REC		The P2 card is not recordable. Detailed information is provided on the
			FUNCTION screen of MODE CHECK. See the relevant section of the
			MODE CHECK indication area.
	CANNOT PLAY		Clip cannot be played back perhaps because no P2 card is loaded, or the
			P2 card contains no clips.
	COMM ERROR		Displayed when disconnection between microcomputers continues for a
			specified period or longer.
	TEXT MEMO		Text memo has been added.
	TEXT MEMO INVALID		Text memo has not been successfully added.
	MARK ON/OFF		Shot mark been added or deleted. For information on shot marks, see [Shot
			Mark Function] (page 41).
	SHOT MARK INVALID		This is displayed when shot marks cannot be added.
	UPDATING		Clip information is being updated. Playback operation disabled.
	USB DEVICE		AJ-HPX2000 is in USB DEVICE mode. When communication is disabled,
			the indication blinks.
	USB HOST		Indicates that the camera-recorder is set to the USB HOST mode. When the
			external hard disk is not successfully recognized, then the indication blinks.
	THUMBNAIL OPEN		Thumbnail is being manipulated.
	1394 INITIAL ERROR		Displayed when the connection of the DVCPRO/DV connector is abnormal
			(when AJ-YAD800G is attached).
	PROXY REC P2&SD		Displayed when proxy recording on either the P2 card or the SD memory
			card starts (when AJ-YAX800G is attached, the PROXY REC item on the
			VF INDICATOR2 screen is turned on).
	PROXY REC P2		Displayed when proxy recording on the P2 card starts (when AJ-YAX800G is
			attached, the PROXY REC item on the VF INDICATOR2 screen is turned on).
	NEAR END (SD)		When the remaining free space on the SD Memory card drops below one
			minute during proxy recording, the message is displayed (when AJ-
			YAX800G is attached).
	EOM (SD)		Displayed when full capacity is reached during proxy recording on the SD
			memory card (when AJ-YAX800G is attached).
	PROXY CARD ERROR		Displayed when proxy recording stops because of failure on either the video
			encoder card or the stream.(when AJ-YAX800G is attached).
	SD CARD WRITE ERR		Displayed when a failure occurs on the SD memory card during proxy
			recording, and only recording on the SD memory card stops.(when AJ-
			YAX800G is attached).
	CANNOT DISP IN VF		No return video, playback, or externally input video can be output to the
			viewfinder.
	TC REGEN		The RET button was pressed to regenerate the time code as the time code
			for the last clip recorded on a P2 card.
	SLOT SEL		This blinks while the recording slots of P2 cards are switched after pressing
			the USER switch where the SLOT SEL function is assigned.
	SLOT SEL INVALID		This is displayed if the recording slots of P2 cards cannot be switched when
			the USER switch where the SLOT SEL function is assigned is pressed.
	DIR NG CARD		This is displayed when the recording starts or completes while a P2 card with
	SLOT1/2/3/4/5		an irregular directory arrangement is inserted or data are recorded after
			inserting an irregular P2 card.
	RUN DOWN CARD		This is displayed when the recording starts or completes with an expired P2
	SLOT1/2/3/4/5		card or when data are recorded after inserting an expired P2 card.
14. Time code indication	TCG	12:59:59:20	TCG (time code generator value)
	TCR	12:59:59:20	TCR (time code reader value)
	(V)UBG	AB CD EF 00	UBG VUBG (User bits generator value)
	(V)UBR	12 34 56 78	UBR VUBR (User bits reader value)
	CTL	–1:59:59:20	Displays CTL count.
15. D.ZOOM	DZa2/a3/a4		Magnification of the digital zoom when the unit is in digital zoom mode.
16. Extender	EX		Lens extender used.

74 Adjustments and Settings for Recording : Viewfinder Screen Status Displays