1. Parts and their functions

A bus crosspoint buttons [1 to 5] B bus crosspoint buttons [1 to 5]

These are used to select the materials to be output to the PGM bus, PST bus, AUX bus, PinP bus and KEY-F/S bus.

When a button is pressed and the material allocated to that button is selected, the indicator of the button lights.

Depending on the status of the BUS DELEGATION button () indicators, the operation performed differs as follows.

1.While the indicators of all three buttons are off:

When one of the crosspoint buttons is pressed, the materials of the buses which execute the background transitions are selected.

[B bus crosspoint buttons]

These are used to select the PST bus materials.

When a button from [1] to [5] is pressed, the material assigned to the corresponding XPT1 to XPT5 is selected.

When a button from [1] to [5] is pressed while the SHIFT button is held down, the material assigned to the corresponding XPT6 to XPT10 is selected.

[A bus crosspoint buttons]

These are used to select the PGM bus materials.

When a button from [1] to [5] is pressed, the material assigned to the corresponding XPT1 to XPT5 is selected.

When a button from [1] to [5] is pressed while the SHIFT button is held down, the material assigned to the corresponding XPT6 to XPT10 is selected.

Memo

Using the OSD menu, A/B, PGM(A)/PST(B) or PGM(B)/PST(A) can be selected as the bus mode. The description given above applies when the PGM(A)/PST(B) has been selected.

Refer to “1-1-4. Selecting the bus mode” (<Operations and Settings> Operating Instructions).

2.When the indicator of the AUX button is blinked:

When one of the crosspoint buttons is pressed, the AUX bus material is selected.

[B bus crosspoint buttons]

When a button from [1] to [5] is pressed, the material assigned to the corresponding XPT1 to XPT5 is selected.

When a button from [1] to [5] is pressed while the SHIFT button is held down, the material assigned to the corresponding XPT6 to XPT10 is selected.

[A bus crosspoint buttons]

When a button from [1] to [5] is pressed, PGM, PVW, KEY OUT, CLN or MV is selected respectively.

3.While the indicator of the PinP button is blinked:

When a B crosspoint button is pressed, the PinP bus material is selected.

[B bus crosspoint buttons]

When a button from [1] to [5] is pressed, the material assigned to the corresponding XPT1 to XPT5 is selected.

When a button from [1] to [5] is pressed while the SHIFT button is held down, the material assigned to the corresponding XPT6 to XPT10 is selected.

4.While the indicator of the KEY-F/S button is blinked:

When one of the crosspoint buttons is pressed, the key fill bus or key source bus material is selected.

[B bus crosspoint buttons]

These are used to select the key fill bus materials. When a button from [1] to [5] is pressed, the material assigned to the corresponding XPT1 to XPT5 is selected. When a button from [1] to [5] is pressed while the SHIFT button is held down, the material assigned to the corresponding XPT6 to XPT10 is selected.

[A bus crosspoint buttons]

These are used to select the key source bus materials.

When a button from [1] to [5] is pressed, the material assigned to the corresponding XPT1 to XPT5 is selected.

When a button from [1] to [5] is pressed while the SHIFT button is held down, the material assigned to the corresponding XPT6 to XPT10 is selected.

15

Page 106
Image 106
Panasonic AW-HS50N  Memo , While the indicators of all three buttons are off, Bus crosspoint buttons