-39-
6. If you want to change the video output level
(picture contrast), move the "I" cursor for
LEVEL and adjust the level.
7. Move the cursor to RET and press the CAM
(SET) key to return to the CAM SET UP menu.
To return to the camera picture, press the [F4]
button.
●Shutter Speed Setting (SHUTTER)
You can select a shutter speed from among 1/60 (OFF),
1/100, 1/250, 1/500, 1/1000, 1/2000,
1/4 000, and 1/10 000 seconds.The factory default set-
ting is OFF.
The electronic shutter speed changes as follows by
using the joystick:
●Gain Control (AGC)
You can set the gain (brightness level portion of an
image) to automatic level adjustment ON (LOW, MID,
HIGH) or fixed level (OFF).
The factory default setting is ON (MID).
Note: For more information, refer to Digital Noise
Reduction on page 43.
●Synchronization (SYNC)
You can select the internal sync (INT) mode or the line-
lock sync (LL) mode. Additionally, this model accepts
the VD2 signal (vertical drive signal multiplexed with the
composite video output signal) from a specified compo-
nent. Whenever the VD2 signal is supplied to this cam-
era, the camera automatically switches to the VD2 sync
mode.
When you select the line-lock sync (LL) mode, you can
adjust vertical phase.
The factory default setting is INT.
Important Notices:
1. The priority of sync modes is given as follows:
1. Multiplexed vertical drive (VD2) (highest priori-
ty)
2. Line-lock (LL)
3. Internal sync (INT) (lowest priority)
2. Whenever the vertical drive pulse (VD2) is supplied
to the camera, the camera sync mode is automati-
cally switched to the multiplexed vertical drive
pulse (VD2) regardless of the selected sync mode.
Line-lock Sync Mode (LL)
1. Move the cursor to SYNC and select LL by using
the joystick. LL sync mode is not available when
the multiplexed vertical drive (VD2) pulse is sup-
plied.
2. After selecting LL, press the CAM (SET) key.
The SYNC menu appears on the monitor screen.
3. Supply the video output signal of the camera to be
adjusted and the reference video output signal (for
example, Camera 1) to a dual-trace oscilloscope.
4. Set the dual-trace oscilloscope to the vertical rate
and expand the vertical sync portion on the oscillo-
scope.
** ALC CONT **
BACK LIGHT COMP
BLC
MASK SET
LEVEL
RET
OFF
••|•••••
- +
OFF (1/60) 1/100
1/10 000 1/4 000 1/2 000 1/1 000
1/250 1/500
** SET UP **
CAMERA ID ON O
ALC/MANUAL ALC O
SHUTTER OFF
AGC ON(MID)
SYNC INT
WHITE BAL ATW O
AF MODE MANUAL
EL-ZOOM ON
SENS UP OFF
MOTION DET OFF
RET SPECIAL O
** SET UP **
CAMERA ID ON O
ALC/MANUAL ALC O
SHUTTER OFF
AGC ON(MID)
SYNC INT
WHITE BAL ATW O
AF MODE MANUAL
EL-ZOOM ON
SENS UP OFF
MOTION DET OFF
RET SPECIAL O
** SET UP **
CAMERA ID ON O
ALC/MANUAL ALC O
SHUTTER OFF
AGC ON(MID)
SYNC INT
WHITE BAL ATW O
AF MODE MANUAL
EL-ZOOM ON
SENS UP OFF
MOTION DET OFF
RET SPECIAL O
** SET UP **
CAMERA ID ON O
ALC/MANUAL ALC O
SHUTTER OFF
AGC ON(MID)
SYNC LL O
WHITE BAL ATW O
AF MODE MANUAL
EL-ZOOM ON
SENS UP OFF
MOTION DET OFF
RET SPECIAL O