Metro Intranet Access | Patton electronic 3086 instruction

2 • Product Overview	Model 3086 G.SHDSL Integrated Access Device User Guide

PCM encoded voice from a PBX are carried in split-DSL- bandwidth mode to a Central Office. At a Service Provider location the Model 3096RC separates PCM voice and IP data traffic for transport over the WAN

Metro Intranet Access

Patton’s Model 3086 symmetrical G.SHDSL modulation scheme, allows deployment in back-to-back configu- rations for Metro Intranet Access with the following benefits.

•Low cost creation of VPN and Intranet Access

•Can be connected locally or via TDM networks

•Secure networking and more efficient Traffic Engineering

26	Product Overview

Image 26

Patton electronic 3086 manual Metro Intranet Access

Contents

Shdsl Integrated Access Device Patton Electronics Company, Inc Contents Basic Application Configurations Contents Specialized Configurations 113 Contacting Patton for assistance 143 Cable Recommendations 157 Contents Page Structure About this guideAudience Precautions About this guide Factory default parametersSafety when working with electricity Mouse conventions Typographical conventions used in this documentGeneral conventions Chapter contents General Information Model 3086 G.SHDSL IAD overview Model 3086 G.SHDSL IAD overviewGeneral attributes TDM Interface Shdsl CharacteristicsEthernet Protocol support Management PPP SupportATM Protocols Security Model WAN DSL Console port outlined in red Rear panel connectors and switchesPower connector Line port outlined in yellow RJ-11/4 DSL line port uses pins 2 and 3 of the RJ-11 portEthernet port outlined in green Product Overview Product Overview Applications Overview IP/FR and Voice over DSL Internet/Extranet AccessIP/FR and TDM Access Product Overview Metro Intranet Access Quick Start Installation What you will need Hardware installationInstalling the AC power cord Connecting network cables Quick Start Installation IP address Quick Start modification Web Operation and ConfigurationPC Configuration IP address has now been successfully changed Model 3086 home page displays see Figure Model 3086 menu structure is shown in on Model 3086 Menu Structure Basic Application Configurations Basic Application Configurations IPoA Routed RFC Introduction Routed WAN Services Bridged WAN Services TDM Port Rear panel power and interface connectors X.21 Ports Connecting the 3086 serial port to a DTEConnecting the 3086 serial port to a DCE Interfaces Configuring the V.35 or X.21 port via DIP switches X.21 Ports DIP switches location Switch Bank S2 Switch Position Function Factory Default Selected Option Switch Bank S3 T1 Interface T1 Interface Connection T1 Interface Configuration DIP Switch Configuration Data Rate kbps Figuration only Web Interface Configuration Line Code The 3086 T1 interface uses B8ZS E1 Interface E1 Interface Connection Description of S2 options follows the table E1/CRC S3-8 Setting Web Interface Configuration CLI configuration Using the 3086 as a simple modem TDM data over DSLCLI configuration Wait for configuration saved message… Saving configuration… Circuit ID Web browser configurationClear Error Counters Intended DSL Data Rate Terminal Type Intended Serial Interface Data RateDSL Rate Number of i Bit TDM Plus Ethernet Traffic Assigning bandwidth to serial and Ethernet ports Selecting PCM modeSelecting the DSL link speed Central or Remote terminal Master/Slave Select between Annex a and Annex B To select Annex B type For 3086 a at the prompt typeFor 3086 B type Circuit ID Intended Serial Interface Data Rate Interface Type Two stand-alone units directly connected Using the 3086 in Routed or Bridged applicationsModel 3086 Remote Configuration Steps PPPoH Bridged Ethernet extension Hdlc Pppoh Bridged Leave User name and Password blank. Click on Apply Model 3086 Central Configuration Steps PPPoH Bridged Model 3086 Remote Configuration Steps PPPoH Routed Network Extension HDLC-PPPoH Routed Model 3086 G.SHDSL Integrated Access Device User Guide Click on Configure Basic Application Configurations Model 3086 Central Configuration Steps PPPoH Routed Using the 3086 in Routed or Bridged applications Dslam Connections with remote CPE units Bridged application configurations to a DslamRFC 1483 Bridged Configuration Model 3086 Remote Configuration Steps RFC 1483 Bridged Model 3086 Central Configuration Steps RFC 1483 Bridged PPPoH Bridged Configuration Dslam Connections with remote CPE units Model 3086 Central Configuration Steps PPPoH Bridged PPPoA Bridged RFC 2364 Configuration Model 3086 Remote Configuration Steps PPPoA Bridged Model 3086 CentralConfiguration Steps PPPoA Bridged VPI = VCI = LLC header mode = off Hdlc header mode = off RFC 1483 Routed Routed application configurations to a DslamModel 3086 Remote Configuration Steps RFC 1483 Routed Model 3086 G.SHDSL Integrated Access Device User Guide Basic Application Configurations Model 3086 Central Configuration Steps RFC 1483 Routed One IP interface was called ip1 with an IP address Ip set interface ip1 ipaddress 192.168.100.2 Dslam Connections with remote CPE units Basic Application Configurations PPPoH Routed Ip set interface ip1 ipaddress 192.168.100.2 Dslam Connections with remote CPE units Basic Application Configurations Model 3086 Central Configuration Steps PPPoH Routed Basic Application Configurations Basic Application Configurations Model 3086 Remote-Client Configuration Steps PPPoA Routed PPPoA Routed RFC User Namefred Passwoodfredspass Click on Configure Chap Basic Application Configurations Dslam Connections with remote CPE units Model 3086 Central-Server Configuration Steps PPPoA Routed 100 101 Local IP Magic Number MRU 102 103 104 105 106 107 Model 3086 Remote Configuration Steps IPoA RoutedIPoA Routed RFC 108 109 110 111 Model 3086 Central Configuration Steps IPoA RoutedVPI0 VCI700 WAN IP address Click on Apply 112 Specialized Configurations RIP and RIPv2 Static Route IP ConfigurationsRouter Dhcp Server and Relay Specialized Configurations 115 DNS Client 116 DNS Relay Mode 117 IP Configurations Security Configuring the IAD 120 121 Configuring the security interfacesSecurity Deleting a Firewall Policy 122 Firewall Policies Enabling the FirewallFirewall Portfilters Firewall policy named item0 is now deleted Security Triggers 124 125 126 Scan Attack Block DurationDefault = 86400 secondsIntrusion Detection System IDS 127 Intrusion Detection System IDS NAT Network Address Translation Enabling NAT 130 131 Global address pool and reserved mapNAT Network Address Translation 132 Monitoring Status Status LEDs 134 Diagnostics Procedure Software UpgradesConfiguration Ping Operating Remote Digital Loopback RDL-DSL Loop DiagnosticsOperating Local Analog Loopback LAL-Serial Port Loop 137 138 T1/E1 DiagnosticsNetwork Loop T1/E1 Local Loop 139 QRSS-BIT Error Rate Diagnostics 140 Transceiver Status AlarmsT1/E1 connection Status FDL statistics T1 only BIT Error Rate V.52 Diagnostics 142 Contacting Patton for assistance Contact information Warranty coverageOut-of-warranty service Returns for credit Shipping instructions Return for credit policyRMA numbers Contacting Patton for assistancePage Appendix a Compliance information Radio and TV Interference FCC Part SafetyCompliance CE Declaration of Conformity Industry Canada Notice Authorized European RepresentativeFCC Part 68 Acta Statement 149 150 Appendix B Specifications Ethernet General CharacteristicsShdsl Characteristics 152 64K/G.703 Port 3086/RIF Model Sync Serial InterfaceT1/E1 Interface 3086/RIK and RIT models only Protocol Support Management PPP SupportATM Protocols 154 Security DimensionsPower and Power Supply Specifications Compliance Standard Requirements 156 Appendix C Cable Recommendations Adapter DSL CableEthernet Cable Foot 3 m, RJ-11/RJ-11 refer to RJ-11non-shielded port on Appendix D Physical Connectors RJ-11 non-shielded port Assuming the MDI-X switch is in the out positionRJ-45 shielded 10/100 Ethernet port RJ-45 non-shielded RS-232 console port EIA-561 Physical Connectors 35 M/34 Connector35 DB-25 Female Connector Serial port IEC 320 connector two prong Power input21 DB-15 Connector E1/T1 RJ-48C Connector 162 Appendix E Command Line Interface CLI Operation 163 Local VT-100 emulation CLI TerminologyProduces a list of numbered transport objects Remote Telnet Then Using the ConsoleCommand Line Interface CLI Operation 165 Adding new users Administering user accountsSetting user passwords Following information is returned Controlling user access Changing user settingsControlling login access Shdsl Commands 168 To establish the DSL linkFor CPE remote unit 169 170 Appendix F Interworking Functions Information Interworking Functions Information Frame Relay Local Management Interface LMI Configuration OptionsManagementType Default Value nomaintenance 173 T392Value Default Value MgtAutoStart Default Value FalseT391Value Default Value FullReportCycle Default Value Command lmi show CLI Configuration MethodsShow current configuration Set configuration variable FRS Configuration Options Frame Relay Service Interworking FRF.8Web Configuration Methods DE Mapping 177 Translation ModeFecn Mapping FRS Name 178 Show one of the eight groups CLI Configuration MethodCommand frs set group # variable value Set variable attributes on a specified group 180 Set variable attributes on a specified channelFRS Overview Screen Group/Channel Level Configuration Screen 181 182 FRN Configuration OptionsFrame Relay Network Interworking FRF.5 Port Level Configuration Options 183 Channel Level Configuration Options 184 Show detailed information about a specific port CLI Configuration Methods for Port Level ManagementList all ports available to the system 185 Understanding the Channel Level View Command frn set port# variable valueConfiguration Management of the Channel Level Variables 186 187 Set Configuration Variables associated with the ChannelsCommand frn set port# channel # variable value Port Level Information Screen 188 189 Channel Level Information ScreenPacket Information Screen Frame Relay Ethernet Based Operations Frame Relay Configuration OptionsFrame Relay CLI Configuration Options List all active Frame Relay Channels Clear all Frame Relay TransportsDelete the specified transport 191 Configuration Variables Available Serial Interface ConfigurationWeb Based Configuration of the Frame Relay Channel Clock Mode 193 Show current configuration settingsGain help about the Serial Interface Ping and Trace Route Web Interface ConfigurationsPing commands from the CLI Interface 194 Start Trace Route ip traceroute start Trace Route from the CLI InterfaceDefine Usage ip traceroute 195 Restore Configuration Backup and Restore FeaturesBackup Configuration Ping and traceroute from the web interface