Hardware installation, What you will need | Patton electronic 3086

3 • Quick Start Installation	Model 3086 G.SHDSL Integrated Access Device User Guide

Hardware installation

If you are already familiar with Model 3086 IAD installation and configuration, this chapter will enable you to finish the job quickly. Installation consists of the following:

•Preparing for the installation (see section “What you will need”)

•Hooking up cables, verifying that the unit will power up, and running a HyperTerminal session (see section “Connecting network cables” on page 29)

•Changing the IP address from the factory default setting (see section “IP address Quick Start modification” on page 30)

•Launching a web browser in preparation for configuring the modem (see “Web Operation and Configura- tion” on page 30)

What you will need

•Model 3086 G.SHDSL IAD

•Ethernet cable with RJ45 plugs on each end (included with IAD)

•DB9-RJ45 Adapter (included with IAD)

•RJ45/RJ45 straight-through cable for connecting to control port (included with IAD)

•PC computer with HyperTerminal or equivalent VT-100 emulation program, or an ASCII (“dumb”) terminal.

Installing the AC power cord

This section describes installing the power cord into the IEC-320 connector on the 3086. Do not connect the male end of the power cord to the power outlet at this time. Do the following:

1.Install the power cable into Power connector (see figure 2). The AC main socket outlet shall be within 10 feet (3 meters) of the equipment and shall be easily accessible.

Figure 2. Power connector location on rear panel

28	Hardware installation

Image 28

Patton electronic 3086 manual Hardware installation, What you will need, Installing the AC power cord

Contents

Shdsl Integrated Access Device Patton Electronics Company, Inc Contents Basic Application Configurations Contents Specialized Configurations 113 Contacting Patton for assistance 143 Cable Recommendations 157 Contents Page Audience About this guideStructure Precautions Safety when working with electricity Factory default parametersAbout this guide General conventions Typographical conventions used in this documentMouse conventions Chapter contents General Information General attributes Model 3086 G.SHDSL IAD overviewModel 3086 G.SHDSL IAD overview Shdsl Characteristics EthernetTDM Interface Protocol support ATM Protocols PPP SupportManagement Security Model WAN DSL Power connector Rear panel connectors and switchesConsole port outlined in red Ethernet port outlined in green RJ-11/4 DSL line port uses pins 2 and 3 of the RJ-11 portLine port outlined in yellow Product Overview Product Overview Applications Overview Internet/Extranet Access IP/FR and TDM AccessIP/FR and Voice over DSL Product Overview Metro Intranet Access Quick Start Installation Installing the AC power cord Hardware installationWhat you will need Connecting network cables Quick Start Installation Web Operation and Configuration PC ConfigurationIP address Quick Start modification IP address has now been successfully changed Model 3086 home page displays see Figure Model 3086 menu structure is shown in on Model 3086 Menu Structure Basic Application Configurations Basic Application Configurations IPoA Routed RFC Introduction Routed WAN Services Bridged WAN Services TDM Port Rear panel power and interface connectors Connecting the 3086 serial port to a DTE Connecting the 3086 serial port to a DCEX.21 Ports Interfaces Configuring the V.35 or X.21 port via DIP switches X.21 Ports DIP switches location Switch Bank S2 Switch Position Function Factory Default Selected Option Switch Bank S3 T1 Interface T1 Interface Connection T1 Interface Configuration DIP Switch Configuration Data Rate kbps Figuration only Web Interface Configuration Line Code The 3086 T1 interface uses B8ZS E1 Interface E1 Interface Connection Description of S2 options follows the table E1/CRC S3-8 Setting Web Interface Configuration CLI configuration Using the 3086 as a simple modem TDM data over DSLCLI configuration Wait for configuration saved message… Saving configuration… Web browser configuration Clear Error CountersCircuit ID Intended DSL Data Rate DSL Rate Number of i Bit Intended Serial Interface Data RateTerminal Type TDM Plus Ethernet Traffic Selecting PCM mode Selecting the DSL link speedAssigning bandwidth to serial and Ethernet ports Central or Remote terminal Master/Slave For 3086 B type For 3086 a at the prompt typeSelect between Annex a and Annex B To select Annex B type Circuit ID Intended Serial Interface Data Rate Interface Type Using the 3086 in Routed or Bridged applications Model 3086 Remote Configuration Steps PPPoH BridgedTwo stand-alone units directly connected Ethernet extension Hdlc Pppoh Bridged Leave User name and Password blank. Click on Apply Model 3086 Central Configuration Steps PPPoH Bridged Model 3086 Remote Configuration Steps PPPoH Routed Network Extension HDLC-PPPoH Routed Model 3086 G.SHDSL Integrated Access Device User Guide Click on Configure Basic Application Configurations Model 3086 Central Configuration Steps PPPoH Routed Using the 3086 in Routed or Bridged applications RFC 1483 Bridged Configuration Bridged application configurations to a DslamDslam Connections with remote CPE units Model 3086 Remote Configuration Steps RFC 1483 Bridged Model 3086 Central Configuration Steps RFC 1483 Bridged PPPoH Bridged Configuration Dslam Connections with remote CPE units Model 3086 Central Configuration Steps PPPoH Bridged PPPoA Bridged RFC 2364 Configuration Model 3086 Remote Configuration Steps PPPoA Bridged Model 3086 CentralConfiguration Steps PPPoA Bridged VPI = VCI = LLC header mode = off Hdlc header mode = off Model 3086 Remote Configuration Steps RFC 1483 Routed Routed application configurations to a DslamRFC 1483 Routed Model 3086 G.SHDSL Integrated Access Device User Guide Basic Application Configurations Model 3086 Central Configuration Steps RFC 1483 Routed One IP interface was called ip1 with an IP address Ip set interface ip1 ipaddress 192.168.100.2 Dslam Connections with remote CPE units Basic Application Configurations PPPoH Routed Ip set interface ip1 ipaddress 192.168.100.2 Dslam Connections with remote CPE units Basic Application Configurations Model 3086 Central Configuration Steps PPPoH Routed Basic Application Configurations Basic Application Configurations Model 3086 Remote-Client Configuration Steps PPPoA Routed PPPoA Routed RFC User Namefred Passwoodfredspass Click on Configure Chap Basic Application Configurations Dslam Connections with remote CPE units Model 3086 Central-Server Configuration Steps PPPoA Routed 100 101 Local IP Magic Number MRU 102 103 104 105 106 IPoA Routed RFC Model 3086 Remote Configuration Steps IPoA Routed107 108 109 110 VPI0 VCI700 WAN IP address Click on Apply Model 3086 Central Configuration Steps IPoA Routed111 112 Specialized Configurations IP Configurations RouterRIP and RIPv2 Static Route Dhcp Server and Relay Specialized Configurations 115 DNS Client 116 DNS Relay Mode 117 IP Configurations Security Configuring the IAD 120 Security Configuring the security interfaces121 Deleting a Firewall Policy 122 Enabling the Firewall Firewall PortfiltersFirewall Policies Firewall policy named item0 is now deleted Security Triggers 124 125 Intrusion Detection System IDS Scan Attack Block DurationDefault = 86400 seconds126 127 Intrusion Detection System IDS NAT Network Address Translation Enabling NAT 130 NAT Network Address Translation Global address pool and reserved map131 132 Monitoring Status Status LEDs 134 Diagnostics Software Upgrades ConfigurationProcedure Ping Diagnostics Operating Local Analog Loopback LAL-Serial Port LoopOperating Remote Digital Loopback RDL-DSL Loop 137 Network Loop T1/E1 Diagnostics138 T1/E1 Local Loop 139 QRSS-BIT Error Rate Diagnostics 140 Alarms T1/E1 connection StatusTransceiver Status FDL statistics T1 only BIT Error Rate V.52 Diagnostics 142 Contacting Patton for assistance Warranty coverage Out-of-warranty serviceContact information Returns for credit Return for credit policy RMA numbersShipping instructions Contacting Patton for assistancePage Appendix a Compliance information Safety ComplianceRadio and TV Interference FCC Part CE Declaration of Conformity Authorized European Representative FCC Part 68 Acta StatementIndustry Canada Notice 149 150 Appendix B Specifications General Characteristics Shdsl CharacteristicsEthernet 152 Sync Serial Interface T1/E1 Interface 3086/RIK and RIT models only64K/G.703 Port 3086/RIF Model Protocol Support PPP Support ATM ProtocolsManagement 154 Dimensions Power and Power Supply SpecificationsSecurity Compliance Standard Requirements 156 Appendix C Cable Recommendations DSL Cable Ethernet CableAdapter Foot 3 m, RJ-11/RJ-11 refer to RJ-11non-shielded port on Appendix D Physical Connectors Assuming the MDI-X switch is in the out position RJ-45 shielded 10/100 Ethernet portRJ-11 non-shielded port RJ-45 non-shielded RS-232 console port EIA-561 35 M/34 Connector 35 DB-25 Female ConnectorPhysical Connectors Serial port Power input 21 DB-15 Connector E1/T1 RJ-48C ConnectorIEC 320 connector two prong 162 Appendix E Command Line Interface CLI Operation 163 CLI Terminology Produces a list of numbered transport objectsLocal VT-100 emulation Remote Telnet Using the Console Command Line Interface CLI OperationThen 165 Administering user accounts Setting user passwordsAdding new users Following information is returned Changing user settings Controlling login accessControlling user access Shdsl Commands For CPE remote unit To establish the DSL link168 169 170 Appendix F Interworking Functions Information Interworking Functions Information LMI Configuration Options ManagementType Default Value nomaintenanceFrame Relay Local Management Interface 173 MgtAutoStart Default Value False T391Value Default ValueT392Value Default Value FullReportCycle Default Value CLI Configuration Methods Show current configurationCommand lmi show Set configuration variable Frame Relay Service Interworking FRF.8 Web Configuration MethodsFRS Configuration Options DE Mapping Fecn Mapping Translation Mode177 FRS Name 178 CLI Configuration Method Command frs set group # variable valueShow one of the eight groups Set variable attributes on a specified group FRS Overview Screen Set variable attributes on a specified channel180 Group/Channel Level Configuration Screen 181 Frame Relay Network Interworking FRF.5 FRN Configuration Options182 Port Level Configuration Options 183 Channel Level Configuration Options 184 CLI Configuration Methods for Port Level Management List all ports available to the systemShow detailed information about a specific port 185 Command frn set port# variable value Configuration Management of the Channel Level VariablesUnderstanding the Channel Level View 186 Command frn set port# channel # variable value Set Configuration Variables associated with the Channels187 Port Level Information Screen 188 Packet Information Screen Channel Level Information Screen189 Frame Relay CLI Configuration Options Frame Relay Configuration OptionsFrame Relay Ethernet Based Operations Clear all Frame Relay Transports Delete the specified transportList all active Frame Relay Channels 191 Serial Interface Configuration Web Based Configuration of the Frame Relay ChannelConfiguration Variables Available Clock Mode Gain help about the Serial Interface Show current configuration settings193 Web Interface Configurations Ping commands from the CLI InterfacePing and Trace Route 194 Trace Route from the CLI Interface Define Usage ip tracerouteStart Trace Route ip traceroute start 195 Backup and Restore Features Backup ConfigurationRestore Configuration Ping and traceroute from the web interface