Manuals / Patton electronic / Computer Equipment / Network Card

Patton electronic 3086 manual Basic Application Configurations

Models: 3086

1 196

Download 196 pages 1.92 Kb

Page 34


4 • Basic Application Configurations	Model 3086 G.SHDSL Integrated Access Device User Guide
Switch S3-8		52
Web Interface Configuration		53
Using the 3086 as a simple modem (TDM data over DSL)		54
DIP Switch Configuration		54
CLI configuration		54
3086 A CLI configuration		54
3086 B CLI configuration		55
Web browser configuration		56
Circuit ID		56
Clear Error Counters		56
Intended DSL Data Rate		56
Actual DSL Rate		56
Intended Serial Interface Data Rate		57
DSL Rate: Number of i Bit		57
Terminal Type		57
Interface Type		58
PCM Mode		58
PCM Transmit Polarity		58
PCM Receive Polarity		58
Loopback		58
Annex Type		58
Line Probe		58
TDM Plus Ethernet Traffic		58
CLI configuration		59
Selecting the DSL link speed		59
Selecting PCM mode		59
Assigning bandwidth to serial and Ethernet ports		59
Central or Remote terminal (Master/Slave)		59
Interface Type		60
Annex Type		60
Web Browser Configuration		60
Circuit ID		61
Clear Error Counters		61
Intended DSL Data Rate		61
Actual DSL Rate		61
Intended Serial Interface Data Rate		62
DSL Rate: Number of i Bit		62
Terminal Type		62
Interface Type		63
PCM Mode		63
PCM Transmit Polarity		63
PCM Receive Polarity		63
Loopback		63
Annex Type		63

34

Image 34

Patton electronic 3086 manual Basic Application Configurations

Contents

Shdsl Integrated Access Device Patton Electronics Company, Inc Contents Basic Application Configurations Contents Specialized Configurations 113 Contacting Patton for assistance 143 Cable Recommendations 157 Contents Page Audience About this guideStructure Precautions Safety when working with electricity Factory default parametersAbout this guide General conventions Typographical conventions used in this documentMouse conventions Chapter contents General Information General attributes Model 3086 G.SHDSL IAD overviewModel 3086 G.SHDSL IAD overview TDM Interface Shdsl CharacteristicsEthernet Protocol support ATM Protocols PPP SupportManagement Security Model WAN DSL Power connector Rear panel connectors and switchesConsole port outlined in red Ethernet port outlined in green RJ-11/4 DSL line port uses pins 2 and 3 of the RJ-11 portLine port outlined in yellow Product Overview Product Overview Applications Overview IP/FR and Voice over DSL Internet/Extranet AccessIP/FR and TDM Access Product Overview Metro Intranet Access Quick Start Installation Installing the AC power cord Hardware installationWhat you will need Connecting network cables Quick Start Installation IP address Quick Start modification Web Operation and ConfigurationPC Configuration IP address has now been successfully changed Model 3086 home page displays see Figure Model 3086 menu structure is shown in on Model 3086 Menu Structure Basic Application Configurations Basic Application Configurations IPoA Routed RFC Introduction Routed WAN Services Bridged WAN Services TDM Port Rear panel power and interface connectors X.21 Ports Connecting the 3086 serial port to a DTEConnecting the 3086 serial port to a DCE Interfaces Configuring the V.35 or X.21 port via DIP switches X.21 Ports DIP switches location Switch Bank S2 Switch Position Function Factory Default Selected Option Switch Bank S3 T1 Interface T1 Interface Connection T1 Interface Configuration DIP Switch Configuration Data Rate kbps Figuration only Web Interface Configuration Line Code The 3086 T1 interface uses B8ZS E1 Interface E1 Interface Connection Description of S2 options follows the table E1/CRC S3-8 Setting Web Interface Configuration CLI configuration Using the 3086 as a simple modem TDM data over DSLCLI configuration Wait for configuration saved message… Saving configuration… Circuit ID Web browser configurationClear Error Counters Intended DSL Data Rate DSL Rate Number of i Bit Intended Serial Interface Data RateTerminal Type TDM Plus Ethernet Traffic Assigning bandwidth to serial and Ethernet ports Selecting PCM modeSelecting the DSL link speed Central or Remote terminal Master/Slave For 3086 B type For 3086 a at the prompt typeSelect between Annex a and Annex B To select Annex B type Circuit ID Intended Serial Interface Data Rate Interface Type Two stand-alone units directly connected Using the 3086 in Routed or Bridged applicationsModel 3086 Remote Configuration Steps PPPoH Bridged Ethernet extension Hdlc Pppoh Bridged Leave User name and Password blank. Click on Apply Model 3086 Central Configuration Steps PPPoH Bridged Model 3086 Remote Configuration Steps PPPoH Routed Network Extension HDLC-PPPoH Routed Model 3086 G.SHDSL Integrated Access Device User Guide Click on Configure Basic Application Configurations Model 3086 Central Configuration Steps PPPoH Routed Using the 3086 in Routed or Bridged applications RFC 1483 Bridged Configuration Bridged application configurations to a DslamDslam Connections with remote CPE units Model 3086 Remote Configuration Steps RFC 1483 Bridged Model 3086 Central Configuration Steps RFC 1483 Bridged PPPoH Bridged Configuration Dslam Connections with remote CPE units Model 3086 Central Configuration Steps PPPoH Bridged PPPoA Bridged RFC 2364 Configuration Model 3086 Remote Configuration Steps PPPoA Bridged Model 3086 CentralConfiguration Steps PPPoA Bridged VPI = VCI = LLC header mode = off Hdlc header mode = off Model 3086 Remote Configuration Steps RFC 1483 Routed Routed application configurations to a DslamRFC 1483 Routed Model 3086 G.SHDSL Integrated Access Device User Guide Basic Application Configurations Model 3086 Central Configuration Steps RFC 1483 Routed One IP interface was called ip1 with an IP address Ip set interface ip1 ipaddress 192.168.100.2 Dslam Connections with remote CPE units Basic Application Configurations PPPoH Routed Ip set interface ip1 ipaddress 192.168.100.2 Dslam Connections with remote CPE units Basic Application Configurations Model 3086 Central Configuration Steps PPPoH Routed Basic Application Configurations Basic Application Configurations Model 3086 Remote-Client Configuration Steps PPPoA Routed PPPoA Routed RFC User Namefred Passwoodfredspass Click on Configure Chap Basic Application Configurations Dslam Connections with remote CPE units Model 3086 Central-Server Configuration Steps PPPoA Routed 100 101 Local IP Magic Number MRU 102 103 104 105 106 IPoA Routed RFC Model 3086 Remote Configuration Steps IPoA Routed107 108 109 110 VPI0 VCI700 WAN IP address Click on Apply Model 3086 Central Configuration Steps IPoA Routed111 112 Specialized Configurations RIP and RIPv2 Static Route IP ConfigurationsRouter Dhcp Server and Relay Specialized Configurations 115 DNS Client 116 DNS Relay Mode 117 IP Configurations Security Configuring the IAD 120 Security Configuring the security interfaces121 Deleting a Firewall Policy 122 Firewall Policies Enabling the FirewallFirewall Portfilters Firewall policy named item0 is now deleted Security Triggers 124 125 Intrusion Detection System IDS Scan Attack Block DurationDefault = 86400 seconds126 127 Intrusion Detection System IDS NAT Network Address Translation Enabling NAT 130 NAT Network Address Translation Global address pool and reserved map131 132 Monitoring Status Status LEDs 134 Diagnostics Procedure Software UpgradesConfiguration Ping Operating Remote Digital Loopback RDL-DSL Loop DiagnosticsOperating Local Analog Loopback LAL-Serial Port Loop 137 Network Loop T1/E1 Diagnostics138 T1/E1 Local Loop 139 QRSS-BIT Error Rate Diagnostics 140 Transceiver Status AlarmsT1/E1 connection Status FDL statistics T1 only BIT Error Rate V.52 Diagnostics 142 Contacting Patton for assistance Contact information Warranty coverageOut-of-warranty service Returns for credit Shipping instructions Return for credit policyRMA numbers Contacting Patton for assistancePage Appendix a Compliance information Radio and TV Interference FCC Part SafetyCompliance CE Declaration of Conformity Industry Canada Notice Authorized European RepresentativeFCC Part 68 Acta Statement 149 150 Appendix B Specifications Ethernet General CharacteristicsShdsl Characteristics 152 64K/G.703 Port 3086/RIF Model Sync Serial InterfaceT1/E1 Interface 3086/RIK and RIT models only Protocol Support Management PPP SupportATM Protocols 154 Security DimensionsPower and Power Supply Specifications Compliance Standard Requirements 156 Appendix C Cable Recommendations Adapter DSL CableEthernet Cable Foot 3 m, RJ-11/RJ-11 refer to RJ-11non-shielded port on Appendix D Physical Connectors RJ-11 non-shielded port Assuming the MDI-X switch is in the out positionRJ-45 shielded 10/100 Ethernet port RJ-45 non-shielded RS-232 console port EIA-561 Physical Connectors 35 M/34 Connector35 DB-25 Female Connector Serial port IEC 320 connector two prong Power input21 DB-15 Connector E1/T1 RJ-48C Connector 162 Appendix E Command Line Interface CLI Operation 163 Local VT-100 emulation CLI TerminologyProduces a list of numbered transport objects Remote Telnet Then Using the ConsoleCommand Line Interface CLI Operation 165 Adding new users Administering user accountsSetting user passwords Following information is returned Controlling user access Changing user settingsControlling login access Shdsl Commands For CPE remote unit To establish the DSL link168 169 170 Appendix F Interworking Functions Information Interworking Functions Information Frame Relay Local Management Interface LMI Configuration OptionsManagementType Default Value nomaintenance 173 T392Value Default Value MgtAutoStart Default Value FalseT391Value Default Value FullReportCycle Default Value Command lmi show CLI Configuration MethodsShow current configuration Set configuration variable FRS Configuration Options Frame Relay Service Interworking FRF.8Web Configuration Methods DE Mapping Fecn Mapping Translation Mode177 FRS Name 178 Show one of the eight groups CLI Configuration MethodCommand frs set group # variable value Set variable attributes on a specified group FRS Overview Screen Set variable attributes on a specified channel180 Group/Channel Level Configuration Screen 181 Frame Relay Network Interworking FRF.5 FRN Configuration Options182 Port Level Configuration Options 183 Channel Level Configuration Options 184 Show detailed information about a specific port CLI Configuration Methods for Port Level ManagementList all ports available to the system 185 Understanding the Channel Level View Command frn set port# variable valueConfiguration Management of the Channel Level Variables 186 Command frn set port# channel # variable value Set Configuration Variables associated with the Channels187 Port Level Information Screen 188 Packet Information Screen Channel Level Information Screen189 Frame Relay CLI Configuration Options Frame Relay Configuration OptionsFrame Relay Ethernet Based Operations List all active Frame Relay Channels Clear all Frame Relay TransportsDelete the specified transport 191 Configuration Variables Available Serial Interface ConfigurationWeb Based Configuration of the Frame Relay Channel Clock Mode Gain help about the Serial Interface Show current configuration settings193 Ping and Trace Route Web Interface ConfigurationsPing commands from the CLI Interface 194 Start Trace Route ip traceroute start Trace Route from the CLI InterfaceDefine Usage ip traceroute 195 Restore Configuration Backup and Restore FeaturesBackup Configuration Ping and traceroute from the web interface