Manuals / Pelco / Photography / Security Camera

Pelco 9770 manual CM9700-MGR PC Pin-Out Detail, Pc Com Port

Models: 9770

1 66

Page 30

CM9700-MGR		CM9700-CC1
PC COM PORT	RS-232 CABLE	COM 1/COM 2
	RS-232 CABLE
PIN 3 (TX)		PIN 2 (RX)
PIN 2 (RX)		PIN 3 (TX)
PIN 5 (GND)		PIN 5 (GND)
DB9 FEMALE		DB9 FEMALE

Figure 22. CM9700-MGR PC Pin-Out Detail

6.Install any additional system peripheral devices. Refer to the manuals for the individual devices for instructions. Refer to the Data Connections section and your Port Assignments table for directions on which port to use for each device.

7.Connect all power line cords to the equipment. Do not turn on the power until the installation is complete. Refer to the System Start-Upsection.

30	C1555M-G (12/07)

Page 30

Image 30

Pelco 9770 manual CM9700-MGR PC Pin-Out Detail, Pc Com Port

Contents

C1555M-G 12/07 SystemI N S T A L L A T I O N / O P E R A T I O N C1555M-G 12/07 Initialize the CC1 ContentsDisplay a Blue Raster Screen Monitor Color Adjustment Initialize Keyboards Display the CM9770-MXB Software Version LevelList of Illustrations List of Tables Description Matrix Bay MODELSController and CPU Components Network Interface UnitCompatible Receivers KeyboardsOptional Components CM9760-MDA-X CM9760-RELCM9700-CC1 InstallationUNPACKING CM9770-MXBMOUNTING CM9770-MXBFigure 2. Mounting the CM9770-MXB on Top of the Mounting Baffle CM9700-CC1 1. Insert the CM9700-CC1 into the rackInstallation Tips VIDEO INPUT/OUTPUT CONNECTIONSOpening the CM9770-MXB Front Cover Insert or Replace a Video Card INSTALLING VIDEO INPUT CARDS CM9770-VCCHow to Turn On the Pelco V-Sync Signal Remove a Video CardINSTALLING MONITOR OUTPUT CARDS CM9770-VMC Insert or Replace a Monitor CardRemove a Monitor Card Diagnostic Check PERFORMING A BASIC LED CHECKColor INSTALLING REAR PANEL BNC CARDS Insert or Replace a Rear Panel Video BNC Card CM9770-RPCRemove a Rear Panel Video BNC Card CM9770-RPC Change the Termination Jumpers on a Rear Panel Video BNC Card Looping Video Insert or Replace a Rear Panel Monitor BNC Card CM9770-RPM PRIMARY VMC CARD SLOT OPTIONAL SECONDARY VMC CARD SLOT2 CM9770-RPM BNC PANELS SECOND PANEL OPTIONAL VIDEO INPUT/OUTPUT CAPACITY Single BayMONITOR Multiple Bays, Single Node Figure 14. Sample Sideframing System Using an Output Bay Figure 15. Sample Single-Node System with Downframing Networked System Figure 16. Sample Networked SystemTHE POWER SUPPLY MODULE CM9700-MPS INSTALL A BACKUP POWER SUPPLYREMOVE A BACKUP POWER SUPPLY HOW TO REPLACE THE FUSE IN A POWER SUPPLY MODULE HOW TO TURN OFF THE AUDIBLE POWER SUPPLY ALARM CM9505-UPS SYSTEM DEVICE CONNECTIONSPOWER SUPPLY CM9760-KBDFigure 22. CM9700-MGR PC Pin-Out Detail PC COM PORTTable C. Data Connections-Networked System Without a Hot Switch RS-422 COM PORT “SERCOM” CONNECTIONSTable B. Data Connections-Single Node Systems Without a Hot Switch CC1 port 5 and next available sequential ports, as necessarythe hot switch. These connections do not Hot Switch connectionCC1 port 6 and next consecutive ports, as = RX Figure 23. Sample CM9770-MXB to CM9700-CC1 ConnectionDATA CABLE = RX+System Start-Up INITIALIZE THE CC1VERIFY SYSTEM OPERATION INITIALIZE KEYBOARDSDISPLAY A BLUE RASTER SCREEN MONITOR COLOR ADJUSTMENTDISPLAY THE CM9770-MXB SOFTWARE VERSION LEVEL WHITEProgramming Your System GETTING HELP USING CM9700-MGR Operation Switch MonitorsCall a Preset OPERATING YOUR SYSTEMHOW TO EXPAND YOUR SYSTEM AppendixSYSTEM ARCHITECTURE INSTALLING ADDITIONAL MATRIX BAYS-SIDEFRAMING AND DOWNFRAMING SideframingDownframing Figure 31. Downframing with DFC Cards Figure 32. Looping Video Out in a Downframed ConfigurationDownframe Cards Figure 33. DFC CableFigure 34. DFC Card Figure 35. CM9770-DFL CardHOW TO INSTALL OR REPLACE A CM9700-SER CARD IN THE CC1 Figure 37. SER Card Jumper Assignments When LED Is On VIDEO INPUT CARD CM9770-VCC DETAILWhen LED is on or blinking MONITOR OUTPUT CARD CM9770-VMC DETAILColor Data Protection Color SystemPort 1 RS-422 Baud Rate Test ModeNETWORKING CONNECTING SATELLITE DEVICES PROGRAMMING SATELLITE DEVICESHOW TO INSTALL VIDEO PATCH PANELS CM9700-VPP MOUNTING THE CM9770-MXB IN AN OPEN RACK Figure 46. Mounting the CM9770-MXB in an Open RackAUTOEXEC.BAT AND THE BOOT PROCESS DOS ENVIRONMENT AND COMMAND REFERENCETHE BOOT PROCESS Invoking the CM9700 ExecutableNavigating the DOS Directory Tree DOS CommandsFile Names and DOS The Path StatementExample Using the Wild Card CharacterManipulating Files in the DOS Environment ExampleDOS REFERENCE COMMANDSWITCHES EXAMPLESCOMMAND C\FASTHELPLIST SWITCHESSymptom TroubleshootingProblems with the CC1 The VCC Card CF LED Is Illuminated and the AUX LED Is BlinkingSwitch Monitor Display ProblemsLED Indicators on the Power Supply Module Front Panel LabelSpecifications CM9700-CC1VIDEO Design and product specifications subject to change without noticeCM9770-MXB ELECTRICAL GENERALRADIO AND TELEVISION INTERFERENCE Regulatory NoticesCM9780-MXB CM9700-CC1REVISION HISTORY PRODUCT WARRANTY AND RETURN INFORMATIONWARRANTY RETURNSUSA & Canada Tel 800/289-9100 Fax 800/289-9150 International ISO9001Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA Tel 1-559/292-1981 Fax 1-559/348-1120