Manuals / Pelco / Photography / Security Camera

Pelco 9770 manual Downframing with DFC Cards, Looping Video Out in a Downframed Configuration

Models: 9770

1 66

Download 66 pages 18.23 Kb

Page 43

Figure 31. Downframing with DFC Cards

Refer to the Downframing section on the following page for instructions on setting the termination jumpers in the downframed bays.

Figure 31. Downframing with DFC Cards

Figure 32. Looping Video Out in a Downframed Configuration

C1555M-G (12/07)

43

Image 43

Pelco 9770 manual Downframing with DFC Cards, Looping Video Out in a Downframed Configuration

Contents

System C1555M-G 12/07I N S T A L L A T I O N / O P E R A T I O N C1555M-G 12/07 Initialize Keyboards Display the CM9770-MXB Software Version Level ContentsDisplay a Blue Raster Screen Monitor Color Adjustment Initialize the CC1List of Illustrations List of Tables Description Network Interface Unit MODELSController and CPU Components Matrix BayCM9760-MDA-X CM9760-REL KeyboardsOptional Components Compatible ReceiversCM9770-MXB InstallationUNPACKING CM9700-CC1CM9770-MXB MOUNTINGFigure 2. Mounting the CM9770-MXB on Top of the Mounting Baffle 1. Insert the CM9700-CC1 into the rack CM9700-CC1VIDEO INPUT/OUTPUT CONNECTIONS Installation TipsOpening the CM9770-MXB Front Cover Remove a Video Card INSTALLING VIDEO INPUT CARDS CM9770-VCCHow to Turn On the Pelco V-Sync Signal Insert or Replace a Video CardInsert or Replace a Monitor Card INSTALLING MONITOR OUTPUT CARDS CM9770-VMCRemove a Monitor Card PERFORMING A BASIC LED CHECK Diagnostic CheckColor Insert or Replace a Rear Panel Video BNC Card CM9770-RPC INSTALLING REAR PANEL BNC CARDSRemove a Rear Panel Video BNC Card CM9770-RPC Change the Termination Jumpers on a Rear Panel Video BNC Card Looping Video PRIMARY VMC CARD SLOT OPTIONAL SECONDARY VMC CARD SLOT Insert or Replace a Rear Panel Monitor BNC Card CM9770-RPM2 CM9770-RPM BNC PANELS SECOND PANEL OPTIONAL Single Bay VIDEO INPUT/OUTPUT CAPACITYMONITOR Multiple Bays, Single Node Figure 14. Sample Sideframing System Using an Output Bay Figure 15. Sample Single-Node System with Downframing Figure 16. Sample Networked System Networked SystemINSTALL A BACKUP POWER SUPPLY THE POWER SUPPLY MODULE CM9700-MPSREMOVE A BACKUP POWER SUPPLY HOW TO REPLACE THE FUSE IN A POWER SUPPLY MODULE HOW TO TURN OFF THE AUDIBLE POWER SUPPLY ALARM CM9760-KBD SYSTEM DEVICE CONNECTIONSPOWER SUPPLY CM9505-UPSPC COM PORT Figure 22. CM9700-MGR PC Pin-Out DetailCC1 port 5 and next available sequential ports, as necessary RS-422 COM PORT “SERCOM” CONNECTIONSTable B. Data Connections-Single Node Systems Without a Hot Switch Table C. Data Connections-Networked System Without a Hot SwitchHot Switch connection the hot switch. These connections do notCC1 port 6 and next consecutive ports, as = RX+ Figure 23. Sample CM9770-MXB to CM9700-CC1 ConnectionDATA CABLE = RXINITIALIZE THE CC1 System Start-UpINITIALIZE KEYBOARDS VERIFY SYSTEM OPERATIONWHITE MONITOR COLOR ADJUSTMENTDISPLAY THE CM9770-MXB SOFTWARE VERSION LEVEL DISPLAY A BLUE RASTER SCREENProgramming Your System GETTING HELP USING CM9700-MGR OPERATING YOUR SYSTEM Switch MonitorsCall a Preset OperationAppendix HOW TO EXPAND YOUR SYSTEMSYSTEM ARCHITECTURE Sideframing INSTALLING ADDITIONAL MATRIX BAYS-SIDEFRAMING AND DOWNFRAMINGDownframing Figure 32. Looping Video Out in a Downframed Configuration Figure 31. Downframing with DFC CardsFigure 33. DFC Cable Downframe CardsFigure 35. CM9770-DFL Card Figure 34. DFC CardHOW TO INSTALL OR REPLACE A CM9700-SER CARD IN THE CC1 Figure 37. SER Card Jumper Assignments VIDEO INPUT CARD CM9770-VCC DETAIL When LED Is OnMONITOR OUTPUT CARD CM9770-VMC DETAIL When LED is on or blinkingColor Data Protection Test ModeColor System Port 1 RS-422 Baud RateNETWORKING PROGRAMMING SATELLITE DEVICES CONNECTING SATELLITE DEVICESHOW TO INSTALL VIDEO PATCH PANELS CM9700-VPP Figure 46. Mounting the CM9770-MXB in an Open Rack MOUNTING THE CM9770-MXB IN AN OPEN RACKInvoking the CM9700 Executable DOS ENVIRONMENT AND COMMAND REFERENCETHE BOOT PROCESS AUTOEXEC.BAT AND THE BOOT PROCESSThe Path Statement DOS CommandsFile Names and DOS Navigating the DOS Directory TreeExample Using the Wild Card CharacterManipulating Files in the DOS Environment ExampleEXAMPLES COMMANDSWITCHES DOS REFERENCESWITCHES C\FASTHELPLIST COMMANDThe VCC Card CF LED Is Illuminated and the AUX LED Is Blinking TroubleshootingProblems with the CC1 SymptomFront Panel Label Monitor Display ProblemsLED Indicators on the Power Supply Module SwitchCM9700-CC1 SpecificationsGENERAL Design and product specifications subject to change without noticeCM9770-MXB ELECTRICAL VIDEOCM9700-CC1 Regulatory NoticesCM9780-MXB RADIO AND TELEVISION INTERFERENCERETURNS PRODUCT WARRANTY AND RETURN INFORMATIONWARRANTY REVISION HISTORYTel 1-559/292-1981 Fax 1-559/348-1120 ISO9001Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel 800/289-9100 Fax 800/289-9150 International