Manuals / Pelco / Photography / Security Camera

Pelco manual Sample CM9770-MXB to CM9700-CC1 Connection, Data Cable, = Rx+

Models: 9770

1 66

Download 66 pages 18.23 Kb

Page 33

DATA CABLE

CM9700-CC1

REVERSED CABLE

CM9770-MXB

PIN 1

PIN 8

	CM9770-MXB		REVERSED	CM9700-CC1
	CM9770-MXB		DATA CABLE	CM9700-CC1
	RJ-45 PIN-OUTS		DATA CABLE	RJ-45 PIN-OUTS

	PIN 1	= TX+		PIN 1 = TX+
	PIN 2	= TX-		PIN 2 = TX-
	PIN 7	= RX-		PIN 7	= RX-
	PIN 8	= RX+		PIN 8	= RX+

Figure 23. Sample CM9770-MXB to CM9700-CC1 Connection

CM9700-CC1 NODE 7

CM9700-NW1

CM9700-CC1 NODE 5

CM9700-CC1 NODE 6

CM9770-MXB

CM9770-MXB

CM9770-MXB

Figure 24. Sample CM9770-MXB and CM9700-CC1 Connections in a Networked System

C1555M-G (12/07)

33

Image 33

Pelco manual Sample CM9770-MXB to CM9700-CC1 Connection, Data Cable, = Rx+

Contents

C1555M-G 12/07 SystemI N S T A L L A T I O N / O P E R A T I O N C1555M-G 12/07 Display a Blue Raster Screen Monitor Color Adjustment ContentsInitialize the CC1 Initialize Keyboards Display the CM9770-MXB Software Version LevelList of Illustrations List of Tables Description Controller and CPU Components MODELSMatrix Bay Network Interface UnitOptional Components KeyboardsCompatible Receivers CM9760-MDA-X CM9760-RELUNPACKING InstallationCM9700-CC1 CM9770-MXBCM9770-MXB MOUNTINGFigure 2. Mounting the CM9770-MXB on Top of the Mounting Baffle 1. Insert the CM9700-CC1 into the rack CM9700-CC1Installation Tips VIDEO INPUT/OUTPUT CONNECTIONSOpening the CM9770-MXB Front Cover How to Turn On the Pelco V-Sync Signal INSTALLING VIDEO INPUT CARDS CM9770-VCCInsert or Replace a Video Card Remove a Video CardINSTALLING MONITOR OUTPUT CARDS CM9770-VMC Insert or Replace a Monitor CardRemove a Monitor Card Diagnostic Check PERFORMING A BASIC LED CHECKColor INSTALLING REAR PANEL BNC CARDS Insert or Replace a Rear Panel Video BNC Card CM9770-RPCRemove a Rear Panel Video BNC Card CM9770-RPC Change the Termination Jumpers on a Rear Panel Video BNC Card Looping Video Insert or Replace a Rear Panel Monitor BNC Card CM9770-RPM PRIMARY VMC CARD SLOT OPTIONAL SECONDARY VMC CARD SLOT2 CM9770-RPM BNC PANELS SECOND PANEL OPTIONAL VIDEO INPUT/OUTPUT CAPACITY Single BayMONITOR Multiple Bays, Single Node Figure 14. Sample Sideframing System Using an Output Bay Figure 15. Sample Single-Node System with Downframing Figure 16. Sample Networked System Networked SystemTHE POWER SUPPLY MODULE CM9700-MPS INSTALL A BACKUP POWER SUPPLYREMOVE A BACKUP POWER SUPPLY HOW TO REPLACE THE FUSE IN A POWER SUPPLY MODULE HOW TO TURN OFF THE AUDIBLE POWER SUPPLY ALARM POWER SUPPLY SYSTEM DEVICE CONNECTIONSCM9505-UPS CM9760-KBDPC COM PORT Figure 22. CM9700-MGR PC Pin-Out DetailTable B. Data Connections-Single Node Systems Without a Hot Switch RS-422 COM PORT “SERCOM” CONNECTIONSTable C. Data Connections-Networked System Without a Hot Switch CC1 port 5 and next available sequential ports, as necessarythe hot switch. These connections do not Hot Switch connectionCC1 port 6 and next consecutive ports, as DATA CABLE Figure 23. Sample CM9770-MXB to CM9700-CC1 Connection= RX = RX+INITIALIZE THE CC1 System Start-UpINITIALIZE KEYBOARDS VERIFY SYSTEM OPERATIONDISPLAY THE CM9770-MXB SOFTWARE VERSION LEVEL MONITOR COLOR ADJUSTMENTDISPLAY A BLUE RASTER SCREEN WHITEProgramming Your System GETTING HELP USING CM9700-MGR Call a Preset Switch MonitorsOperation OPERATING YOUR SYSTEMHOW TO EXPAND YOUR SYSTEM AppendixSYSTEM ARCHITECTURE Sideframing INSTALLING ADDITIONAL MATRIX BAYS-SIDEFRAMING AND DOWNFRAMINGDownframing Figure 32. Looping Video Out in a Downframed Configuration Figure 31. Downframing with DFC CardsFigure 33. DFC Cable Downframe CardsFigure 35. CM9770-DFL Card Figure 34. DFC CardHOW TO INSTALL OR REPLACE A CM9700-SER CARD IN THE CC1 Figure 37. SER Card Jumper Assignments VIDEO INPUT CARD CM9770-VCC DETAIL When LED Is OnWhen LED is on or blinking MONITOR OUTPUT CARD CM9770-VMC DETAILColor Color System Test ModePort 1 RS-422 Baud Rate Data ProtectionNETWORKING PROGRAMMING SATELLITE DEVICES CONNECTING SATELLITE DEVICESHOW TO INSTALL VIDEO PATCH PANELS CM9700-VPP Figure 46. Mounting the CM9770-MXB in an Open Rack MOUNTING THE CM9770-MXB IN AN OPEN RACKTHE BOOT PROCESS DOS ENVIRONMENT AND COMMAND REFERENCEAUTOEXEC.BAT AND THE BOOT PROCESS Invoking the CM9700 ExecutableFile Names and DOS DOS CommandsNavigating the DOS Directory Tree The Path StatementManipulating Files in the DOS Environment Using the Wild Card CharacterExample ExampleSWITCHES COMMANDDOS REFERENCE EXAMPLESLIST C\FASTHELPCOMMAND SWITCHESProblems with the CC1 TroubleshootingSymptom The VCC Card CF LED Is Illuminated and the AUX LED Is BlinkingLED Indicators on the Power Supply Module Monitor Display ProblemsSwitch Front Panel LabelCM9700-CC1 SpecificationsCM9770-MXB ELECTRICAL Design and product specifications subject to change without noticeVIDEO GENERALCM9780-MXB Regulatory NoticesRADIO AND TELEVISION INTERFERENCE CM9700-CC1WARRANTY PRODUCT WARRANTY AND RETURN INFORMATIONREVISION HISTORY RETURNSWorldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA ISO9001USA & Canada Tel 800/289-9100 Fax 800/289-9150 International Tel 1-559/292-1981 Fax 1-559/348-1120