Pelco C2602M-a SYSTEM SETTINGS

C2602M-A (6/06) 59

To set up alarm inputs and relay outputs

1. From the remote agent application main screen, click the Setup button if the Settings screen is not open. The Settings screen

appears and the Remote Agent tab is displayed.

2. Open the DVR System tab, and then click the Alarm tab.

3. Under Alarm Input, conﬁgure the following settings for each camera:

•Status: Set this to Connected or Disconnected.

•Camera Input: Select the alarm input channel that is associated with the camera. Choices are 1 through 4.

•Type: Select the type of alarm. Choices are Normally Open and Normally Closed.

4. Under Relay Output, conﬁgure the following settings for each camera:

•Relay Out: Set this to On or Off. When the relay is turned on, it will respond to an alarm at the associated camera.

•Mode: Set the relay mode to Transparent or Latched. A transparent relay stops working if the alarm sensor stops working after it

receives an alarm. A latched relay continues operating for the duration set for it even if alarm is received but the alarm sensor stops

working.

•Duration: Select the length of time after an alarm is received that the relay will continue to operate. Duration refers to either the delay

between the occurrence of an alarm and the time at which a relay starts or the length of time that the relay remains in effect after the

alarm occurs. Duration times can set for 5- or 10-second increments for the first minute, and then in one- or two-minute increments for

a maximum of five minutes. Duration may also be set to continue until an operator responds by turning off the alarm with a key (Until

Key-In).

5. Click the Apply button to save the changes and continue to other settings. If you are ﬁnished updating settings, click the OK button to close

the screen.

SYSTEM SETTINGS

Use the System tab to conﬁgure general system information for the DX4000. Some information can be reviewed on this tab but not changed.

Buzzer sound settings, passwords, disk write mode, and network connection and speed can be conﬁgured on the tab.

TIP: Refer to the System tab when you need to locate the software version number. The information on this tab is useful when troubleshooting

the system or upgrading to a newer version.

Figure 73. Conﬁguring System Settings From the Remote Agent

Contents

Main Contents Page List of Illustrations List of Tables Description Features MODELS Overview of the System DX4000 DX4000 Controls CONTROLS ON THE FRONT PANEL OF THE DX4000 VIDEO CONTROL BUTTONS ON THE FRONT PANEL OF THE DX4000 OPERATING THE DX4000 FROM THE REMOTE CONTROL Before You Begin To start the DX4000 STARTING AND STOPPING THE DX4000 CHOOSING A USER ACCOUNT Main Window Overview CHANGING THE DISPLAY MODE CHANGING THE INFORMATION DISPLAYED ON THE MONITOR To change the screen sequencing mode ADJUSTING MENU SETTINGS DISPLAY MENU RECORD MENU CAMERA MENU AUDIO MENU ALARM MENU SYSTEM MENU BACK UP MENU CHANGING PASSWORDS RESETTING PASSWORDS To reset the passwords FACTORY DEFAULT SETTINGS Changing the Screen Layout SCREEN ROTATION MODE SCREEN VIEW SELECTION Controlling Cameras from the DX4000 PAN, TILT AND ZOOM CONTROLS ADJUSTING THE FOCUS OR IRIS ON A CAMERA WORKING WITH PRESETS To create a preset To run a preset To run a predened preset Using Preset 95 WORKING WITH PATTERNS To set up a pattern To run a pattern MODIFYING CAMERA SETTINGS To modify camera settings Page MODIFYING AUDIO SETTINGS To modify audio recording settings To modify live audio settings MODIFYING IMAGE RECORDING SETTINGS To modify image recording settings MODIFYING ALARMS AND RELAYS To modify alarm inputs To modify relay outputs Creating Recording Schedules SETTING UP A RECORDING SCHEDULE Page Page Page SETTING UP ALARM-BASED RECORDING Page Monitoring Live Video To change the screen mode To view a specic video channel in single mode Working With Recorded Video SEARCHING FOR VIDEO Page Page PLAYING RECORDED VIDEO BACKING UP VIDEO To back up video Page Working With the Remote Agent Application ABOUT THE REMOTE AGENT OVERVIEW OF THE MAIN SCREEN REMOTE AGENT CONTROL BUTTONS STARTING AND STOPPING THE REMOTE AGENT To start the remote agent To stop the remote agent CONFIGURING THE REMOTE AGENT To create a network connection for the DX4000 To congure optional settings on the remote agent CONFIGURING THE DX4000 FROM THE REMOTE AGENT RECORDING SETTINGS To set up recording quality To set up recording schedules To set up alarm recording To set up motion detection Page CAMERA SETTINGS To congure cameras AUDIO SETTINGS To set up audio recording To set up live audio ALARM SETTINGS To set up alarm inputs and relay outputs SYSTEM SETTINGS To review system information To congure buzzer sounds To modify passwords To congure the disk write mode To disconnect remote agent connections To set the network speed CONTROLLING CAMERAS FROM THE REMOTE AGENT To control PTZ cameras To adjust the focus MONITORING LIVE VIDEO FROM THE REMOTE AGENT CONTROLLING AUDIO To listen to or disable audio CAPTURING LIVE VIDEO FROM THE REMOTE CLIENT WORKING WITH RECORDED VIDEO ON THE REMOTE AGENT SEARCHING FOR RECORDED VIDEO Page Page BACKING UP VIDEO To back up video To save a snapshot To print a snapshot VIEWING VIDEO WITH THE BACKUP PLAYER To view recorded video with the backup player To authenticate recorded video with the backup player About the Web Client STARTING THE WEB CLIENT Page PRODUCT WARRANTY AND RETURN INFORMATION REVISION HISTORY