Pelco ES30TI manual Maintenance and Troubleshooting

Models: ES30TI

1 60
Download 60 pages 63.45 Kb
Page 52
Image 52

Maintenance and Troubleshooting

MAINTENANCE

Clean the enclosure window periodically with a mild nonabrasive detergent in water and a soft cloth to help maintain picture clarity.

TROUBLESHOOTING

NOTE: The system contains no user-serviceable parts. If there is a problem with your system, it must be returned to Pelco for servicing.

Symptom: Degrading video quality

From time to time, image quality may degrade.

1.Perform a manual FFC. After manually performing this process, the camera restarts the frequency clock and resets the baseline temperature (refer to Flat Field Correction (FFC) on page 29).

2.If the problem persists, perform the troubleshooting steps for Symptom: No video or poor video on page 53.

Symptom: System does not operate

1.Check system input voltage.

2.The Esprit system is protected by a resettable overcurrent protective device located in the transformer module. Whenever a fault condition is experienced in the system causing excessive current flow through the protective device, a change occurs that will prevent current flow. The protective device will remain in this state as long as power is applied and the system fault remains. The protective device will reset itself after power has been removed for a few minutes and will operate normally when the system fault has been repaired.

3.Check the system power and video BNC connections.

Symptom: No control/sluggish control (Coaxitron)

1.Check for correct type and length of coaxial cable.

2.Check for correct coaxial termination (refer to the controller manual to determine proper termination of video input). Normal load termination is 75 ohms. When looping through VCRs or multiplexers, make sure the signal is terminated at the end device. Some termination symptoms and problems are listed below.

Symptom

Problem

Extremely bright video

No termination or high resistance

Over contrast or contrast level of monitor needs to

Double termination (37.5 ohms)

be increased to maximum for a good video image

 

3.If pan/tilt operation is sluggish, check the controller manual to make sure the control signal is set in the extended mode, not standard mode.

Symptom: No control (RS-422/RS-485)

1.Check for correct cable type and length. The maximum cable distance for RS-422 communication over 24-gauge wire is 4,000 feet (1,219 m). Pelco recommends using shielded twisted pairs, such as Belden 9843 or similar cable, that meets or exceeds the basic requirements for EIA RS-422 or RS-485 applications.

2.Check for correct wire connections between transmitting device (such as the CM6700 Series matrix system) and Esprit system receiver. Correct connections are from the transmitting device TX+ to Esprit system RX+ and from the transmitting device TX- to Esprit system RX-.

3.Check for correct DIP switch settings.

52

C1307M-C (8/07)

Page 52
Image 52
Pelco ES30TI manual Maintenance and Troubleshooting

ES30TI specifications

The Pelco ES30TI is a high-performance security camera designed for robust surveillance applications. This cutting-edge device combines innovative technology with user-friendly features to deliver exceptional video quality and reliability.

One of the main features of the ES30TI is its advanced imaging capabilities. Equipped with a high-resolution image sensor, this camera captures crisp, detailed video footage even in challenging lighting conditions. The low-light performance is enhanced by its infrared (IR) capabilities, allowing it to provide clear images in total darkness, making it ideal for nighttime surveillance. The camera also supports multiple resolutions and frame rates, offering flexibility to meet various security needs.

In terms of design, the Pelco ES30TI is built with durability in mind. Its rugged, weather-proof housing ensures that it can withstand harsh environmental conditions, making it suitable for both indoor and outdoor applications. The camera's compact and sleek design allows for discreet installation, which is particularly advantageous in urban settings where aesthetics may be a concern.

The ES30TI also integrates advanced technologies to enhance its functionality. One notable feature is the intelligent video analytics capabilities. This includes motion detection, line crossing detection, and intrusion detection. These features help in identifying potential security breaches and alerting users promptly. Additionally, the camera can be easily integrated with existing security systems, providing a seamless security experience.

Another significant characteristic of the Pelco ES30TI is its ease of use. The camera is designed with a user-friendly interface that allows for straightforward configuration and management. Users can access live feeds and recorded footage remotely through a secure network connection, providing peace of mind whether they are on-site or away.

Moreover, the ES30TI supports multiple video compression formats, allowing for efficient storage and transmission of video data. This ensures that the camera can deliver high-quality video while optimizing bandwidth and storage requirements, making it cost-effective for long-term use.

In summary, the Pelco ES30TI is a versatile and reliable surveillance solution equipped with advanced imaging technology, weather-resistant design, intelligent analytics, and user-friendly features. Its combination of performance and durability makes it an excellent choice for a wide range of security applications. Whether monitoring public spaces, commercial properties, or private residences, the ES30TI delivers the quality and reliability that security professionals demand.