32
aMyexternal receiver does notdisplay the programme
number
Duringinstallation, the externalreceiver will beswitched to a
differentprogramme number. If thereceiver does notdisplay the
programmenumber, you mustcheck the 'Videowindow' (left top
cornerin the GUIDE Plus+®system)to see whetherswitching has
takenplace.
-Select on the DVD-Recorder the socket where the receiver is connected
using CHANNELq,CHANNEL r(e.g. EXT2for EXT2
AUX-I/O)
-Please check the TV show in the 'Video window' in the left top corner
ofthe screen.
-Check whether the picture changes during the next step ( OK button).
4Readthe information on the screen carefully.
Confirmwith OK .
PTheDVD recorderwill nowattempt to usethe G-Link
connectionon the externalreceiver to select a different
programmenumber (e.g.12). Thisprogramme number
dependson yourexternal receiver.
5Hasthe external receiver been switched to the programme
numberdisplayed on thescreen?
If this is the case, select 'YES'.
If no switching has taken place, select 'NO'.
aMyexternal receiver has notswitched tothe other
programmenumber.
-Check that theexternal receiveris connectedand switched on.
-Check the connection and position of the G-LINK transmitter.
-For another attemptwith anew codeof thechosen brand,select 'NO'.
-Confirm with OK on the remotecontrol.
-If the receiverhas notswitched yet,select 'NO'again and confirm with
OK. It may take several attempts for a receiver brand.
Ifyou returnto thesetup screen afterconfirming 'NO', your receiver
maynot havebeen installed.Check the connectionsagain.
-Tune your externalreceiver tothe TVchannel whichtransmits the
GUIDEPlus+®data (see table in the section 'General information'). If
thisTV channel is available at the internal tuner of the DVD-recorder,
selectthis channel.
-Wait till theGUIDE Plus+®datais loaded (24 hours) and try the
switchover again.
Thecontrol data of the external receivers are automatically updated
(completed)via the GUIDEPlus+®system. This is done throughthe
aerial,the cable, or the external receiver. You do not need to bring the
deviceto a servicecentre.
-If your receiverstill doesnot switch,note thetype and manufacturerof
yourexternal receiver and call the customer support service in your
country.You will find the telephone number on the back of this
instructionmanual.
6Yourexternal receiver has nowbeen installed.
7Press OKto return to the setup overview.
aIwant toinstall additionalexternal receivers
Wheninstalling additional external receivers,please observe the
following:The external receiverwhich is controlledby the G-LINK
transmittermust be belowthe otheradditional receivers. The
IR(infrared)remote control signal isreflected diagonally upwards and
cantherefore be usedto controladditional external receivers which
areon top.
Finalise setup
Setup Home
PressAorBto select. Then press OK to confirm.
Setup
Chooseitemto set up :
Language English
Country UnitedKingdom
Postalcode XXXXX
Externalreceiver1 None
Externalreceiver2 None
Externalreceiver3 None
1Checkthe settings shown on the screen.
If the settingsare not correct, choose the line in which you want
tochange the settingsand confirm with OK.
2Pressthe green functionbutton to leave the screen.
OIf you want to view a demonstration of the GUIDE Plus+®
systemselect 'View Demo' with Band confirm with OK .
If you start the demo, programmed recordings can be deleted.
OIf youdo not want to see the demonstration of the GUIDE
Plus+®system,end using GUIDE/TV .
3Thiscompletes the set-up process for the GUIDE Plus+®system.
4Switchthe DVD-recorder to the TV channel which transmits the
GUIDEPlus+®data. The rightTV-channel for yourcountry you
willin the table in the chapter 'The GUIDE Plus+®system' in the
section'General information'.
Leavethe DVD recorder switched on during the night to load the
GUIDEPlus+®data.
Theinformation will be available in the next 24 hours.
5If data are available check in the 'Editor' screen that the TV
channelwhich transmitsthe GUIDE Plus+®datais allocated to the
rightprogramme number. Changethe programme number if
necessary.
The GUIDE Plus+® System