Powerware 10001100 kVA 7.3 Single UPS Operation

UPS OPERATING INSTRUCTIONS

EATON Powerware® 9395 UPS (1000–1100 kVA) Installation and Operation Manual S 164201764 Rev 1 www.powerware.com 7−11

7.3 Single UPS Operation

NOTE A Field Installed UPM (FI−UPM) is always designated as UPM 4.

7.3.1 Starting the UPS in Normal Mode

To start the UPS system:

1. If the UPS contains input breaker CB1, verify that input breaker CB1 is open.

2. Close the UPS input feeder circuit breaker.

3. Close the UPS Bypass input feeder circuit breaker.

4. Observe the UPS control panel display becoming active, indicating logic power.

5. Press the CONTROLS pushbutton on the main menu bar. The System Status

screen is displayed.

6. On the System Status screen, verify the UPS status is SHUTDOWN and the UPM

status is OFFLINE.

7. Close the battery breaker.

8. If the UPS contains input breaker CB1, close input breaker CB1.

9. On the System Status screen, select the UPS command.

10. Press the CONTROLS pushbutton on the System Status menu bar. The UPS

Control Command screen is displayed.

11. On the UPS Control Command screen, select GO TO NORMAL.

12. Press the SELECT pushbutton on the UPS Command menu bar.

If Auto Bypass is enabled (factory default), the critical load is immediately

supplied by the bypass source, in Bypass mode, until the inverter turns on and

the UPS transfers to Normal mode. The status indicator on the UPS control panel

indicates the UPS is in Bypass mode. If Auto Bypass is not enabled, the UPS

output remains off until the UPS transfers to Normal mode.

13. Verify the following messages display sequentially on the UPM status line:

DC STARTING, CHARGER OFF

INVERTER STARTING

INVERTER SYNCING

ONLINE, CHARGING

The rectifier and inverter turn on. The inverter continues to ramp up to full

voltage.

Once the inverter reaches full voltage, the UPS output contactor K3 closes and

the static switch turns off. Power is now supplied to the critical load in Normal

mode. It takes approximately one minute for the UPS to achieve Normal mode.

The NORMAL status indicator is illuminated. The UPS status indicates ONLINE.

The UPM status indicates ONLINE, CHARGING.

Contents

Main IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS CONSIGNES DE SCURIT IMPORTANTES CONSERVER CES INSTRUCTIONS Table of Contents Page Page Page List of Figures Page Chapter 1 Introduction 1.1 UPS Standard Features 1.1.1 Installation Features 1.1.2 Control Panel 1.1.3 Customer Interface S 1.1.4 Advanced Battery Management 1.1.5 Power Management Software 1.2 Options and Accessories 1.2.1 Field Installed UPM 1.2.2 Inherent Redundancy 1.2.3 Sync Control 1.2.4 Distributed Bypass System 1.3 Battery System 1.4 Basic System Configurations S 1.5 Using This Manual 1.6 Conventions Used in This Manual S 1.7 Symbols, Controls, and Indicators 1.8 For More Information S 1.9 Getting Help Chapter 2 Safety Warnings IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS S D A N G E S A V E R T I S S E M E N T S A T T E N T I O N S Page Page Chapter 3 UPS Installation Plan and Unpacking 3.1 Creating an Installation Plan 3.2 Preparing the Site 3.2.1 Environmental and Installation Considerations S S S S Page Page Page Page Figure 3-10. Remote EPO Switch Dimensions 3.2.2 UPS System Power Wiring Preparation Page Page Page Page Table 3-9. Supplied Intercabinet Wiring Terminal Hardware Kit Page Table 3-11. Supplied External Wiring Terminal Hardware Kit Table 3-12. Recommended Installation Parts and Tools (Not Supplied by Eaton) Table 3-13. Power Cable Conduit Requirements Page Page 3.2.3 UPS System Interface Wiring Preparation 3.2.4 Distributed Bypass Power Wiring Preparation 3.3 Inspecting and Unpacking the UPS Cabinets S 1. Carefully inspect the outer packaging for evidence of damage during transit. Page Page Page Chapter 4 UPS System Installation 4.1 Preliminary Installation Information Refer to the following while installing the UPS system: S installation notes. Page Page Figure 4-3. Removing the UPM Section Left Side Shipping Bracket 4.3 Mechanically Joining the Sections Page Page 4.4 Electrically Connecting the Sections Page Page Figure 4-8. ISBM Section Intercabinet Power Terminal Locations Figure 4-9. ISBM Section Input Power Terminal Detail Figure 4-10. ISBM Section Battery Input Power Terminal Detail Figure 4-11. ISBM Section Output Power Terminal Detail Figure 4-12. UPS Intercabinet Interface Harness Locations Page 4.5 Field Installed UPM Installation 4.6 Battery System Installation 4.7 Distributed Bypass Tie Cabinet Installation 4.8 Installing UPS External and Battery Power Wiring 4.8.1 External Power Wiring Installation Figure 4-15. ISBM and UPM Section Debris Shields Figure 4-16. ISBM Section Conduit and Wire Entry Locations Page Figure 4-17. Distributed Bypass Wire Length Figure 4-18. ISBM Section Power Terminal Locations Figure 4-19. ISBM Section Power Terminal Detail AA 4.8.2 Battery Power Wiring Figure 4-20. ISBM Section Power Terminal Detail BB Common Battery Figure 4-21. ISBM Section Power Terminal Detail CC Separate Battery 4.9 Installing Interface Connections 4.9.1 TB1, TB2, and TB3 Connections (Other than TB1 Battery Interface Connections) Page Table 4-1. TB1, TB2, and TB3 Interface Connections Figure 4-23. Interface Terminal Detail Figure 4-24. Typical Alarm Relay Connection Figure 4-25. Terminal Blocks TB1, TB2, and TB3 Connector Assignments 4.9.2 TB1 Battery Interface Connections Figure 4-26. Typical Battery Interface Connection Common Battery System Figure 4-27. Typical Battery Interface Connection Separate Battery System 4.9.3 XSlot Connections 4.10 Installing a REPO Switch Page Page 4.11 Installing Options, Accessories, and Distributed Bypass Control Wiring 4.12 Initial Startup 4.13 Completing the Installation Checklist Installation Checklist Distributed Bypass Installation Checklist Notes Chapter 5 Installing Options and Accessories 5.1 Installing an Optional Powerware Hot Sync CAN Bridge Card Page Page 5.2 Installing Distributed Bypass Control Wiring UPS 1 UPS 2 UPS 3 UPS 4 Figure 5-3. Distributed Bypass System Can and PullChain Simplified Interface Wiring Page INSTALLING OPTIONS AND ACCESSORIES Figure 5-6. Distributed Bypass PullChain Wiring with MOBs Shielded Twisted Pair Shielded Twisted Pair Shielded Twisted Pair Table 5-4. PullChain Wiring Terminations with MOBs 5.3 Installing an Optional Remote Monitor Panel II Figure 5-7. Remote Monitor Panel II and Relay Interface Module II Terminal Locations 5.4 Installing an Optional Relay Interface Module II Page 5.5 Installing an Optional Supervisory Contact Module II Page 5.6 Accessory Mounting Dimensions Figure 5-12 through Figure 5-14 show the dimensions of the RMP II, the RIM II, and the SCM II. Figure 5-12. Remote Monitor Panel II Dimensions Figure 5-13. Relay Interface Module II Dimensions Figure 5-14. Supervisory Contact Module II Dimensions Page Page Page Chapter 6 Understanding UPS Operation 6.1 UPS System Overview 6.2 Single UPS 6.2.1 Modes S S S 6.2.2 Normal Mode 6.2.3 Bypass Mode 6.2.4 Battery Mode Page 6.3 Single UPS Unit System Oneline Configurations Figure 6-5. Four UPM UPS System, Dual-Feed, Common Battery System CC Figure 6-6. Four UPM UPS System, Output Dual-Feed, Separate Battery System Figure 6-7. Three UPM UPS System, Dual-Feed, Common Battery System CC Figure 6-8. Three UPM UPS System, Dual-Feed, Separate Battery System Figure 6-9. Simplified DualFeed UPS with Maintenance Bypass Panel 6.4 Multiple UPS Distributed Bypass System 6.4.1 Multiple UPS Parallel System Modes S S S 6.4.2 Normal Mode Distributed Bypass 6.4.3 Bypass Mode Distributed Bypass 6.4.4 Battery Mode Distributed Bypass Page 6.5 Multiple UPS Distributed Bypass System Oneline Configurations *** Figure 6-13. Typical Distributed Bypass System (1+1 and 2+0 Configurations) UPS 3 ***** Figure 6-14. Typical Distributed Bypass System (2+1 and 3+0 Configurations) UPS 3 UPS 4 ******* Figure 6-15. Typical Distributed Bypass System (3+1 and 4+0 Configurations) Chapter 7 UPS Operating Instructions This section describes how to operate the UPS. 7.1 UPS Controls and Indicators 7.1.1 Control Panel 7.1.2 Circuit Breaker 7.2 Using the Control Panel S S S 7.2.1 Status Indicators 7.2.2 System Events S Page Page 7.2.6 Display Menu Operation Table 7-3 describes the menu functions and and how to use them. Table 7-3. Display Menu Operation Table 7-3. Display Menu Operation (continued) Page Table 7-4. Typical System Status Messages Table 7-5. Command Menu Operation Page 7.3 Single UPS Operation 7.3.1 Starting the UPS in Normal Mode 7.3.2 Starting the UPS in Bypass Mode 7.3.3 Starting the UPMs Page 7.3.4 Transfer from Normal to Bypass Mode 7.3.5 Transfer from Bypass to Normal Mode 7.3.6 Transfer from Normal to Bypass Mode and Shut Down UPS 7.3.7 Single UPM Shutdown 7.3.8 UPS and Critical Load Shutdown 7.3.9 Charger Control 7.3.10 Using the UPS LOAD OFF Pushbutton or Command 7.3.11 Using the Remote Emergency Poweroff Switch UPS OPERATING INSTRUCTIONS Figure 7-7. REPO Operation Power is present inside the UPS cabinet until the upstream input feeder circuit breaker is opened. Deactivated Unlock pushbutton to release Activated 7.4 Multiple UPS Distributed Bypass Operation 7.4.1 Starting the Distributed Bypass System in Normal Mode 7.4.2 Starting the Distributed Bypass System in Bypass Mode 7.4.3 Starting the UPSs UPMs Page 7.4.4 Transfer from Normal to Bypass Mode 7.4.5 Transfer from Bypass to Normal Mode 7.4.6 Transfer from Normal to Bypass Mode and Shut Down all UPSs 7.4.7 Single UPM Shutdown 7.4.8 UPS and Critical Load Shutdown 7.4.9 Charger Control 7.4.10 Using the UPS LOAD OFF Pushbutton or Command 7.4.11 Using the Remote Emergency Poweroff Switch Page Chapter 8 Communication 8.1 XSlot Cards S 8.2 eNotify Service 8.2.1 eNotify Service Features S 8.2.2 Installing eNotify Service 8.3 Powerware LanSafe Power Management Software 8.4 Remote Notification S S S S S S 8.5 Terminal Mode S S S S 8.5.1 Display UPS Control Panel 8.5.2 Event History Log Figure 8-2. Sample Event History Log 8.6 Building Alarm Monitoring 8.7 General Purpose Relay Contact 8.8 Remote Monitor Panel II The RMP II contains a local horn and the backlit status indicators listed in Table 8-1. Table 8-1. RMP II Status Indicators 8.9 Relay Interface Module II 8.10 Supervisory Contact Module II Chapter 9 UPS Maintenance 9.1 Important Safety Instructions S S S S S S S S S 9.2 Performing Preventive Maintenance 9.2.1 DAILY Maintenance 9.2.2 MONTHLY Maintenance Page Page 9.2.3 PERIODIC Maintenance 9.2.4 ANNUAL Maintenance 9.2.5 BATTERY Maintenance 9.3 Installing Batteries 9.4 Recycling the Used Battery or UPS S A T T E N T I O N S S S Chapter 10 Product Specifications 10.1 Model Numbers 10.2 Specifications 10.2.1 UPS Input 10.2.2 UPS Output 10.2.3 UPS Environmental Warranty LIMITED FACTORY WARRANTY FOR THREE-PHASE POWERWARE UPS PRODUCTS