Document Revision History | Q-Logic SANBOX2-64 specification

SANbox2-64 Fibre Channel Switch
Installation Guide

Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for illustrative purposes only. QLogic Corporation makes no representation nor warranty that such applications are suitable for the specified use without further testing or modification. QLogic Corporation assumes no responsibility for any errors that may appear in this document.

QLogic, SANbox, SANbox2, SANblade, SANsurfer, and Multistage are trademarks or registered trademarks of QLogic Corporation.

Java and Solaris are registered trademarks of Sun Microsystems, Inc.

Pentium III is a registered trademark of Intel Corporation.

Linux is a registered trademark of Linus Torvalds.

Microsoft, Windows NT, and Windows 2000, and Internet Explorer are trademarks of Microsoft Corporation.

NetScape Navigator is a registered trademark of Netscape Communications Corporation.

Red Hat is a registered trademark of Red Hat Software Inc.

All other brand and product names are trademarks or registered trademarks of their respective owners.

Document Revision History

Revision A, Release, March 2003

© 2000–2003 QLogic Corporation

First Printed: May 2001

All Rights Reserved Worldwide.

Printed in U.S.A.

QLogic Corporation, 6321 Bury Drive, Eden Prairie, MN 55346

(800) 342-7379 or (952) 932-4000

Page ii

59043-01 A

Image 2

Q-Logic SANBOX2-64 manual Document Revision History, SANbox2-64 Fibre Channel Switch Installation Guide

Contents

SANbox2-64 Fibre Channel Switch Installation Guide SANbox2-64 Fibre Channel Switch Installation Guide Document Revision History Table of Contents Virtual Private Fabric Hard Zones Section InstallationSection Planning Section Diagnostics/Troubleshooting Appendix B Command Line Interface Section Removal/ReplacementAppendix a Specifications SANbox2-6464-Port Fibre Channel Switch Glossary Index Tables Introduction Intended Audience Related Materials Safety Notices Sicherheitshinweise Communications Statements Federal Communications Commission FCC Class a Statement CE Statement Vcci Class a Statement Bsmi Class a Statement Laser Safety Information Electrostatic Discharge Sensitivity Esds Precautions Zugä ngliche Teile Accessible PartsPiè ces Accessibles Training Technical SupportAvailability Contact Information Introduction Technical Support 59043-01 a General Description SANbox2-64 64-Port Fibre Channel Switch Chassis Hardware Slot and Fibre Channel Port Numbering Chassis Controls and LEDs Chassis Controls and Leds Placing the Switch in Maintenance Mode Maintenance ButtonResetting a Switch Heartbeat LED Amber Input Power LED GreenChassis LEDs Fibre Channel Ports Over Temperature LED AmberFan Fail LED Amber Small Form-Factor Pluggable SFP Transceivers Port Status LED Port Modes Fabric Ports Translated Loop Port Expansion Port Ethernet Port Ethernet Port Serial Port Serial Port Pin Identification Power Supply Modules Power Supply Components Fans 10. Fans Switch Management General Description Switch Management 59043-01 a Devices Public and Private Single Switch Fabric with Initiators and Targets Redundancy and Latency Dual Switch Fabric with Initiators and Targets Multiple Chassis Fabrics Domain ID, Principal Priority, and Domain ID Lock Common Topologies Performance Distance Port-to-Port Transmission Combinations BandwidthLatency Port-to-Port Latency Device Access Access Control List Hard Zone Soft Zone Virtual Private Fabric Hard Zones Fabric Management Fabric Security Planning Fabric Security 59043-01 a Fabric Management Workstation Switch Power RequirementsSite Requirements Management Workstation Requirements Installing a Switch Environmental Conditions Mount the Switch SANbox2-64 Rail Kit Install SFP Transceivers Connect the Switch to AC Power Warnung Connect the Management Workstation to the Switch Ethernet and Serial Cable Connections Ethernet Connection Serial Connection Installing SANbox Manager Enter the following command at the Solaris prompt SANsurfer Management Suite Disk Windows Installation SANsurfer Management Suite Disk Linux Installation Enter the following command SANsurfer Management Suite Disk Solaris Installation Press the Enter key Enter the following command SANbox2 Installation Disk Solaris Installation SANbox2 Installation Disk Windows InstallationSANbox2 Installation Disk Linux Installation Configure the Switch Configure the Ports Cable Devices to the Switch Install Firmware Using SANbox Manager to Install Firmware Using the CLI to Install Firmware Enter the following command to install the new firmware Using FTP and the CLI to Install Firmware Close the FTP session Powering Down a Switch Installation Powering Down a Switch 59043-01 a Normal all pass Post DiagnosticsHeartbeat LED Blink Patterns Configuration File System Error Blink Pattern Maintenance Mode PatternFatal Error Blink Pattern Internal Firmware Failure Blink Pattern Diagnostics/Troubleshooting Restore the configuration file Logging Error Port Status LED Indications EPort Isolation Excessive Port Errors Diagnostics/Troubleshooting Post Diagnostics Chassis Diagnostics Chassis and Power Supply LEDs Fan Fail LED is Illuminated Over Temperature LED is IlluminatedInput Power LED Is Extinguished Output Power LED Is Extinguished Power Supply Fault LED is Illuminated Recovering a Switch Maintenance Exit Maintenance Image Unpack Maintenance Copy Log Files Maintenance Reset Network ConfigMaintenance Reset Password File Maintenance Remove Switch Config Marginal Operating Configurations SFP Transceivers CPU Module Removing the CPU Module Removing the CPU Module Installing the CPU Module Ftp put imagefile Blades Choose the Replace task Choose the slot number 6 for example To install a new I/O blade, enter y Removing an I/O Blade Removal/Replacement Blades Cross-Connect Blades CC Blade Slots Removing a CC Blade Switch Cover Removal Installing a CC Blade Installing a CC Blade Removal/Replacement Removing a Power Supply Module Installing a Power Supply Module Removing a Power Supply Module Removing a Fan Removing a Fan Installing a Fan Removal/Replacement Fans 59043-01 a FC-SW-2 FC-GS-3FC-Tape Fibre Channel Element MIB RFC Maintainability Dimensions Electrical Environmental Regulatory Certifications Shortwave Laser SFP 1G/2G multi-mode Longwave Laser SFP 1G/2G single-mode Command Line Interface Logging On to a Switch Command Syntax Commands Table B-1. Commands Listed by Authority Level Syntax Admin CommandAuthority Keywords Alias Command Authority Admin Syntax alias Rename aliasold aliasnew Members aliasRemove alias members Keywords activate config Config CommandSyntax config Edit config Restore Save config Keywords MMDDhhmmCCYY Date CommandSyntax date Fallback Fallback CommandFollowing is an example of the Fallback command Currently active version Command Help CommandHelp command keyword Keyword History History CommandUser Hotswap Command Hotswap Command Line Interface Hotswap Command Keywords cleanup Image CommandAuthority Admin Syntax image cleanup Unpack file Portnumber Lip CommandLip portnumber Accountname Passwd CommandPasswd accountname Authority User Syntax ps Ps CommandExamples The following is an example of the Ps command Displays current system process information Closes the Telnet session Quit CommandAuthority User Syntax quit, exit, or logout Config configname Reset CommandAuthority Admin Syntax reset Zoning Table B-2. Switch Configuration DefaultsTable B-3. Port Configuration Defaults Table B-4. Alarm Threshold Configuration Defaults Table B-5. Snmp Configuration Defaults Table B-6. System Configuration Defaults Set Command Syntax set Log option Setup optionSwitch state Pagebreak state Keywords blade slotnumber Set Config CommandTable B-7. Set Config Port Parameters Port portnumber Command Line Interface Set Config Command Table B-8. Set Config Switch Parameters Table B-9. Set Config Threshold Parameters Threshold Table B-10. Set Config Zoning Parameters With formatting and current values will follow Following is an example of the Set Config Port command Mfstov Following is an example of the Set Config Switch command Following is an example of the Set Config Zoning command Following is an example of the Set Config Threshold command Archive Set Log CommandSet log Clear Save Level levelPort portlist Stops logging of events Set Log Stop commandStop Level keyword to Info at the same time Set Port Command Authority Admin State state Table B-11. Snmp Configuration Settings Set Setup CommandSet setup Snmp System Table B-12. System Configuration Settings Table B-11. Snmp Configuration Settings Values will follow Following is an example of the Set Setup System command System Keywords about Show CommandAlarm Blade Log option Ns option Perf option PagebreakPanel Table B-13. Show Port Parameters LIP Alpd Alps Post log Slot slotnumber Steering domainid Following is an example of the Show Chassis command Following is an example of the Show Fabric command Following is an example of the Show Panel command Following is an example of the Show Port command Following is an example of the Show Slot command Following is an example of the Show Switch command CPU-0 SANbox2-64 N108 # show topology Blade slotnumber Show Config CommandShow config Following is an example of the Show Config Switch command Following is an example of the Show Config Zoning command Following is an example of the Show Config Threshold command Show Log Command Keywords component Following is an example of the Show Log command Following is an example of the Show Log Options commandFollowing is an example of the Show Log Port command Show Perf Command SANbox2-64 N108 # show perf byte Mfg Show Setup CommandShow setup Following is an example of the Show Setup Snmp command Following is an example of the Show Setup System command Shutdown Command Syntax shutdown Keywords port portnumber testtype Test CommandAuthority Admin Syntax test Blade slotnumber Test x external Command Line Interface Test Command Authority User Syntax uptime Uptime CommandExamples The following is an example of the Uptime command Add User CommandAccounts Delete accountname Following is an example of the User List command Following is an example of the User Add commandFollowing is an example of the User Delete command Authority User Syntax whoami Whoami CommandExamples The following is an example of the Whoami command Zone Command Syntax zone Rename zoneold zonenew Members zoneRemove zone members Type zone zonetype Command Line Interface Following is an example of the Zone Members command Following is an example of the Zone Zonesets command Zoneset Command Syntax zoneset Rename zonesetold zonesetnew Delete zonesetRemove zoneset zonelist Zones zoneset Edit Zoning CommandKeywords active Opens a Zoning Edit session Following is an example of the Zoning List command Command Line Interface Command Line Interface Zoning Command 59043-01 a Class 3 Service BootPClass 2 Service Fabric Management Switch Over Temperature LED Input Power LEDOutput Power LED Power On Self Test Post Target Small Form FactorSmall Form-Factor Pluggable Worldwide Name WWNPage Index Index-2 59043-01 a LED Index-4 59043-01 a 59043-01 a Index-5 Index-6 59043-01 a