Configure the Switch | Q-Logic SANBOX2-64 manual

4 – Installation
Installing a Switch

4.2.12

Configure the Switch

Do the following to configure a switch using the SANbox Manager application. Refer to the SANbox2-64 Switch Management User’s Guide for more information about configuring a switch. You can also configure the switch using the CLI. Refer to Appendix B Command Line Interface for more information.

1.Connect to the switch using an Ethernet connection and run SANbox Manager.

2.Open the Fabric menu and select Add Fabric to open the Add a New Fabric window.

3.Enter a fabric name and the IP address of the switch through which to manage the fabric. The default IP address is 10.0.0.1. If this is a new switch, leave the login name and password fields empty, and choose the Add Fabric button. By default, fabric security is disabled, and therefore account names and passwords are not enforced. Refer to the ”Set Setup Command” on page B-40for information about setting fabric security.

4.Open the Switch menu and select Switch Properties. In the Switch Properties window, enter a chassis name. Accept the default domain ID, and choose the OK button.

4-14	59043-01 A

Image 60

Q-Logic SANBOX2-64 manual Configure the Switch

Contents

SANbox2-64 Fibre Channel Switch Installation Guide SANbox2-64 Fibre Channel Switch Installation Guide Document Revision History Table of Contents Section Installation Section PlanningVirtual Private Fabric Hard Zones Section Diagnostics/Troubleshooting Section Removal/Replacement Appendix a SpecificationsAppendix B Command Line Interface SANbox2-6464-Port Fibre Channel Switch Glossary Index Tables Introduction Intended Audience Related Materials Safety Notices Sicherheitshinweise Communications Statements Federal Communications Commission FCC Class a Statement CE Statement Vcci Class a Statement Bsmi Class a Statement Laser Safety Information Electrostatic Discharge Sensitivity Esds Precautions Accessible Parts Piè ces AccessiblesZugä ngliche Teile Technical Support AvailabilityTraining Contact Information Introduction Technical Support 59043-01 a General Description SANbox2-64 64-Port Fibre Channel Switch Chassis Hardware Slot and Fibre Channel Port Numbering Chassis Controls and LEDs Chassis Controls and Leds Maintenance Button Resetting a SwitchPlacing the Switch in Maintenance Mode Input Power LED Green Chassis LEDsHeartbeat LED Amber Over Temperature LED Amber Fan Fail LED AmberFibre Channel Ports Small Form-Factor Pluggable SFP Transceivers Port Status LED Port Modes Fabric Ports Translated Loop Port Expansion Port Ethernet Port Ethernet Port Serial Port Serial Port Pin Identification Power Supply Modules Power Supply Components Fans 10. Fans Switch Management General Description Switch Management 59043-01 a Devices Public and Private Single Switch Fabric with Initiators and Targets Redundancy and Latency Dual Switch Fabric with Initiators and Targets Multiple Chassis Fabrics Domain ID, Principal Priority, and Domain ID Lock Common Topologies Performance Distance Bandwidth LatencyPort-to-Port Transmission Combinations Port-to-Port Latency Device Access Access Control List Hard Zone Soft Zone Virtual Private Fabric Hard Zones Fabric Management Fabric Security Planning Fabric Security 59043-01 a Switch Power Requirements Site RequirementsFabric Management Workstation Management Workstation Requirements Installing a Switch Environmental Conditions Mount the Switch SANbox2-64 Rail Kit Install SFP Transceivers Connect the Switch to AC Power Warnung Connect the Management Workstation to the Switch Ethernet and Serial Cable Connections Ethernet Connection Serial Connection Installing SANbox Manager Enter the following command at the Solaris prompt SANsurfer Management Suite Disk Windows Installation SANsurfer Management Suite Disk Linux Installation Enter the following command SANsurfer Management Suite Disk Solaris Installation Press the Enter key Enter the following command SANbox2 Installation Disk Windows Installation SANbox2 Installation Disk Linux InstallationSANbox2 Installation Disk Solaris Installation Configure the Switch Configure the Ports Cable Devices to the Switch Install Firmware Using SANbox Manager to Install Firmware Using the CLI to Install Firmware Enter the following command to install the new firmware Using FTP and the CLI to Install Firmware Close the FTP session Powering Down a Switch Installation Powering Down a Switch 59043-01 a Post Diagnostics Heartbeat LED Blink PatternsNormal all pass Maintenance Mode Pattern Fatal Error Blink PatternConfiguration File System Error Blink Pattern Internal Firmware Failure Blink Pattern Diagnostics/Troubleshooting Restore the configuration file Logging Error Port Status LED Indications EPort Isolation Excessive Port Errors Diagnostics/Troubleshooting Post Diagnostics Chassis Diagnostics Chassis and Power Supply LEDs Over Temperature LED is Illuminated Input Power LED Is ExtinguishedFan Fail LED is Illuminated Output Power LED Is Extinguished Power Supply Fault LED is Illuminated Recovering a Switch Maintenance Exit Maintenance Image Unpack Maintenance Reset Network Config Maintenance Reset Password FileMaintenance Copy Log Files Maintenance Remove Switch Config Marginal Operating Configurations SFP Transceivers CPU Module Removing the CPU Module Removing the CPU Module Installing the CPU Module Ftp put imagefile Blades Choose the Replace task Choose the slot number 6 for example To install a new I/O blade, enter y Removing an I/O Blade Removal/Replacement Blades Cross-Connect Blades CC Blade Slots Removing a CC Blade Switch Cover Removal Installing a CC Blade Installing a CC Blade Removal/Replacement Removing a Power Supply Module Installing a Power Supply Module Removing a Power Supply Module Removing a Fan Removing a Fan Installing a Fan Removal/Replacement Fans 59043-01 a FC-GS-3 FC-TapeFC-SW-2 Fibre Channel Element MIB RFC Maintainability Dimensions Electrical Environmental Regulatory Certifications Shortwave Laser SFP 1G/2G multi-mode Longwave Laser SFP 1G/2G single-mode Command Line Interface Logging On to a Switch Command Syntax Commands Table B-1. Commands Listed by Authority Level Admin Command AuthoritySyntax Keywords Alias Command Authority Admin Syntax alias Members alias Remove alias membersRename aliasold aliasnew Config Command Syntax configKeywords activate config Edit config Restore Save config Date Command Syntax dateKeywords MMDDhhmmCCYY Fallback Command Following is an example of the Fallback commandFallback Currently active version Help Command Help command keywordCommand Keyword History Command UserHistory Hotswap Command Hotswap Command Line Interface Hotswap Command Image Command Authority Admin Syntax image cleanupKeywords cleanup Unpack file Lip Command Lip portnumberPortnumber Passwd Command Passwd accountnameAccountname Ps Command Examples The following is an example of the Ps commandAuthority User Syntax ps Displays current system process information Quit Command Authority UserCloses the Telnet session Syntax quit, exit, or logout Reset Command Authority Admin Syntax resetConfig configname Table B-2. Switch Configuration Defaults Table B-3. Port Configuration DefaultsZoning Table B-4. Alarm Threshold Configuration Defaults Table B-5. Snmp Configuration Defaults Table B-6. System Configuration Defaults Set Command Syntax set Setup option Switch stateLog option Pagebreak state Set Config Command Table B-7. Set Config Port ParametersKeywords blade slotnumber Port portnumber Command Line Interface Set Config Command Table B-8. Set Config Switch Parameters Table B-9. Set Config Threshold Parameters Threshold Table B-10. Set Config Zoning Parameters With formatting and current values will follow Following is an example of the Set Config Port command Mfstov Following is an example of the Set Config Switch command Following is an example of the Set Config Zoning command Following is an example of the Set Config Threshold command Set Log Command Set logArchive Clear Level level Port portlistSave Set Log Stop command StopStops logging of events Level keyword to Info at the same time Set Port Command Authority Admin State state Set Setup Command Set setupTable B-11. Snmp Configuration Settings Snmp System Table B-12. System Configuration Settings Table B-11. Snmp Configuration Settings Values will follow Following is an example of the Set Setup System command System Show Command AlarmKeywords about Blade Log option Ns option Pagebreak PanelPerf option Table B-13. Show Port Parameters LIP Alpd Alps Post log Slot slotnumber Steering domainid Following is an example of the Show Chassis command Following is an example of the Show Fabric command Following is an example of the Show Panel command Following is an example of the Show Port command Following is an example of the Show Slot command Following is an example of the Show Switch command CPU-0 SANbox2-64 N108 # show topology Show Config Command Show configBlade slotnumber Following is an example of the Show Config Switch command Following is an example of the Show Config Zoning command Following is an example of the Show Config Threshold command Show Log Command Keywords component Following is an example of the Show Log Options command Following is an example of the Show Log Port commandFollowing is an example of the Show Log command Show Perf Command SANbox2-64 N108 # show perf byte Show Setup Command Show setupMfg Following is an example of the Show Setup Snmp command Following is an example of the Show Setup System command Shutdown Command Syntax shutdown Test Command Authority Admin Syntax testKeywords port portnumber testtype Blade slotnumber Test x external Command Line Interface Test Command Uptime Command Examples The following is an example of the Uptime commandAuthority User Syntax uptime User Command AccountsAdd Delete accountname Following is an example of the User Add command Following is an example of the User Delete commandFollowing is an example of the User List command Whoami Command Examples The following is an example of the Whoami commandAuthority User Syntax whoami Zone Command Syntax zone Members zone Remove zone membersRename zoneold zonenew Type zone zonetype Command Line Interface Following is an example of the Zone Members command Following is an example of the Zone Zonesets command Zoneset Command Syntax zoneset Delete zoneset Remove zoneset zonelistRename zonesetold zonesetnew Zones zoneset Zoning Command Keywords activeEdit Opens a Zoning Edit session Following is an example of the Zoning List command Command Line Interface Command Line Interface Zoning Command 59043-01 a BootP Class 2 ServiceClass 3 Service Fabric Management Switch Input Power LED Output Power LEDOver Temperature LED Power On Self Test Post Small Form Factor Small Form-Factor PluggableTarget Worldwide Name WWNPage Index Index-2 59043-01 a LED Index-4 59043-01 a 59043-01 a Index-5 Index-6 59043-01 a