Ricoh 70E - page 92

Preparation for Installation 4-44

II L 00

[Finisher SR5000] with Transit Pass Unit Type DDP

17) Install the SB Cover Paper Guide to the Container Stacker.

SB Cover Paper Guide

M3x6 Screw

Contents

Main Page Page NOTICE TO USER INTRODUCTION Page Table of Contents SAFETY SUMMARY CHAPTER 1. INSTALLATION REQUIREMENTS........................................1-1 CHAPTER 2. UNPACKING ............................................................................2-1 CHAPTER 3. PREPARATION FOR INSTALLATION...................................3-1 CHAPTER 4. INSTALLATION.........................................................................4-1 SAFETY SUMMARY 1. General Safety Guidelines SAFETY SUMMARY (Continued) 2. Hazard Warning Statements 2.1 WARNING Statement Page Page Chapter 1. Installation Requirements 1.1 Application 1.2 Installation Area 1.3 Installation Unit 1.4 Tools Required 1.5 Environmental Conditions 1.6 Input Line Voltage Chapter 2. Unpacking 2.1 Unpacking of the Engine 2.1.1 Components in the package 2.1.2 Unpacking Procedures Page Unpacking 2-4 2.1.3 Parts Check in the Accessory Box II L 03 Page 2.2 Unpacking of the Finisher 2.2.1 Components in the package Page Page 2.2.3 Parts Check in the Accessory Box Page 2.3 Unpacking of the High Capacity Hopper Page 2.4 Unpacking of the Container Stacker 1 or 2 2.4.1 Confirmation of Parts Quantities 2.4.2 2.4.3 Unpacking Procedures Page 2.4.4 Parts Check in the Accessory Box 2.5 Unpacking of the Transit Pass Unit Type DDP 2.5.1 Confirmation of Parts Quantities 2.5.2 Confirmation of the Accessories Parts 2.5.3 Unpacking Procedures 2.6 Unpacking of the Finisher SR5000 Chapter 3. Preparation for Installation 3.1 Preparation for Installation of the Printer 3.1.1 Removing the Protection Tape and Mat from the Engine 3.1.2 Set the PS Air Filter for the Engine Rear Cover 3.1.3 Removing the Protection Tape from 2000 Sheet Hopper. 3.1.4 Removing the Protection Tape from 500 Sheet Hopper ; 2 portion Page Page Page Page Page Page Page Page 3.3 Preparation for Installation of the High Capacity Hopper Page 3.4 Preparation for installation of the Container Stacker 1 or 2 Page Page Chapter 4. Installation 4.1 Installation in the composition of the Printer and Finisher / Finisher SR5000 Page Page Page Page Rear internal view of Printer View of Power Supply interna Page Page Page Page Page H SW1 L Page Page Page Page Page Page Page Page Page Page 4.3 Installation in the composition with the Container Stacker 1 or 2 4.3.1 Connection of the Engine and Container Stacker 1 or 2 Page Page Page Page Page Engine Container Page 4.3.2 Connection of the Container Stacker 1 and Container Stacker 2 Page Page Engine Page 4.3.3 Connection of the Container Stacker 2 and Finisher / Finisher SR5000 Preparation for Installation 4-38 5) Install the Standard Finisher to the Container Stacker 2. Loosen CHECK A Printer Standard Finisher Preparation for Installation 4-40 II L 01 11) Remove the rear covers from the Engine, Container Stacker 2 and Finisher. Page Page Printer SW1 FF N 3 Page Page Page Page Page Page Page Page Chapter 5. Checks 5.1 Confirmation of the paper size indication Page Page 5.2 Printing of the status reports 5.3 Check the print contamination 5.4 Confirmation of the stapling 5.5 Adjustment of paper feeding position of Tray 1