Connecting the Host Computer to the Printer | Seiko Group TM-L60

2-2 Connecting the Host Computer to the Printer

nConnecting the interface cable

Connect the printer to a host ECR (host computer) using an interface cable matching the specifications of the printer and the host ECR (host computer).

Connect the interface cable according to the following procedure. Turn off the printer, power unit, and host computer.

Plug the interface cable connector into the interface connector on the printer; then insert a screwdriver between the rear rubber feet and fasten the screws on both sides of the connector.

Plug the drawer kick-out cable connector into the drawer kick-out connector on the printer (if this connector is covered, you cannot attach a drawer kick-out cable to your printer).

•Remove the drawer kick-out cable by pressing in on the connector’s clip and pulling out.

Serial Interface Cable

Drawer Kick-out Connector

7

Image 13

Seiko Group TM-L60 manual Connecting the Host Computer to the Printer, Connecting the interface cable

Contents

L 6 Page CC Class a FCC Compliance Statement for American Users Introduction Contents Appendix a General Specifications Setting UP Unpacking the Printer 1Checking the Contents of the Box Removing the Protective Material Choosing a Place for the Printer Part names 4Names and Functions of Parts Error red Power greenOperation panel Paper red Plugging in AC adapter Connecting the Power Supply to the Printer Connecting the interface cable Connecting the Host Computer to the Printer Installing the roll paper Installing the Roll Paper Paper Slot How to adjust the paper-end detector Adjusting the Paper-end DetectorPaper-end detector Page Locating the DIP switches Setting the DIP SwitchesSetting the DIP switches Baud Rate Selection DIP-Switch Functions DIP-switch FunctionsPrint Density Selection 1Checking Operation with the Self Test II. Reference Switches Power switch 1Panel Switches and CommandsPaper-feed switch Printable area Printable Area and Label Paper ConditionsLabel paper Miscellaneous Notes Page Error LED red Error Correction Be inspected Error Display ON/OFF Timing Pattern Recovery Command Standby State Display Cleaning the head Cleaning the Head Removing Jammed Paper Cover-open DetectorCover-open detector How to use this table Controlling the printer with commands Commands Command DescriptionsCommand descriptions XXX Command ESC ! n ESC SP n ESC $ n1 n2 ESC & s n m ap s Xam-n+l ESC % n = n 1 + 2 5 6 X n 2 m = 0 ESC * m n1 n2 d k Vertical Direction Horizontal Direction ESC = n ESC 3 n ESC D nkNUL ESC @ Range ESC E n ESC J n ESC G n ESC V n ESC R n ESC n ESC ¥ n1 n2ESC a n Position ESC c 4 n ESC c 5 n ESC p m n1 n2ESC d n ESC u n ESC t n ESC Journal near-end GS*n1n2dn1xn2x8 GS FF Dot Density GS/m GS a m n GS C 0 m n PER Feed switch or turning the power on GS Cl, GS C2, GS c, GS C GS C1 n1 n2 n3 n4 n5 n6 T h c o u n t d o w n GS C2 n1 n2 To stop counting GSC N1 N2 N3 N4 N5 With counting down GS H n With counting up GS f n GS k n d k NUL GS w n GS n1 n2 n3 Program Descriptions How to write program Printing on the roll paperIntroduction Before printing Send Print Data GS H n Initialize printer again Printing bar codes RS-232C must be closed using this command Sample Program onto thermal paper Printing on label paper Sample Program onto thermal label paper Printing specifications Appendix a General SpecificationsCharacters specifications Paper Thermal paper Near-end detector Thermal label paper EMI by using Epson PS-130 Electrical characteristicsExternal dimensions and weight Reliability Appendix B Connectors Signal Name Sender Appendix C Interfaces Specifications RS-232C compatible Serial interface timing Pin Number Signal Name Signal Direction FunctionPage Page International character set Command Name Appendix E Command Summary GS C2 GS C