Esc @, ESC D nkNUL | Seiko Group TM-L60 guide

• Each bit of n is used as follows:

			Value

B i t	D e v i ce	0	1

0	Printer	Invalid	V a l i d

1Undefined

2Undefined

3Undefined

4Undefined

5Undefined

6U n d e f i n ed

7Undefined

[Notes]	• Even when the printer is not selected, it may enter the BUSY
	state due to printer operation.
[Default]	n = 1

ESC @

[Name]	Initialize printer
[Format]	<1B>H<40>H
[Description]	Clears the data in the print buffer and resets the printer mode (to
	the same state as when the power is turned on).
[Note]	• The DIP switches are not read again.
	• The data in the receive buffer is not cleared.
	• Adjustment amount of the label starting position using < GS A >
	command is not cleared.

ESC D [n]kNUL

[Name]	Set horizontal tab positions
[Format]	<1B>H<44>H[<n>]k<00>H

[Range]	1	n	255
	0	k	32
[Description]	Sets		horizontal tab positions.

•"n” specifies the column number from beginning of the line for setting a horizontal tab position.

[n= (Column number) - 1]. For example, when a tab is to be set at column 9, n = 8.

•"k" indicates the total number of horizontal tab positions to be

Set.

33

Image 39

Seiko Group TM-L60 manual Esc @, ESC D nkNUL

Contents

L 6 Page CC Class a FCC Compliance Statement for American Users Introduction Contents Appendix a General Specifications Setting UP Unpacking the Printer 1Checking the Contents of the Box Removing the Protective Material Choosing a Place for the Printer Part names 4Names and Functions of Parts Paper red Power greenError red Operation panel Plugging in AC adapter Connecting the Power Supply to the Printer Connecting the interface cable Connecting the Host Computer to the Printer Installing the roll paper Installing the Roll Paper Paper Slot Adjusting the Paper-end Detector How to adjust the paper-end detectorPaper-end detector Page Setting the DIP Switches Locating the DIP switchesSetting the DIP switches DIP-Switch Functions DIP-switch Functions Baud Rate SelectionPrint Density Selection 1Checking Operation with the Self Test II. Reference 1Panel Switches and Commands Switches Power switchPaper-feed switch Printable Area and Label Paper Conditions Printable areaLabel paper Miscellaneous Notes Page Error LED red Error Correction Be inspected Error Display ON/OFF Timing Pattern Recovery Command Standby State Display Cleaning the head Cleaning the Head Cover-open Detector Removing Jammed PaperCover-open detector How to use this table Controlling the printer with commands Command Descriptions CommandsCommand descriptions XXX Command ESC ! n ESC SP n ESC $ n1 n2 ESC & s n m ap s Xam-n+l ESC % n = n 1 + 2 5 6 X n 2 m = 0 ESC * m n1 n2 d k Vertical Direction Horizontal Direction ESC = n ESC 3 n ESC D nkNUL ESC @ Range ESC E n ESC J n ESC G n ESC V n ESC R n ESC ¥ n1 n2 ESC nESC a n Position ESC c 4 n ESC p m n1 n2 ESC c 5 nESC d n ESC u n ESC t n ESC Journal near-end GS*n1n2dn1xn2x8 GS FF Dot Density GS/m GS a m n GS C 0 m n PER Feed switch or turning the power on GS Cl, GS C2, GS c, GS C GS C1 n1 n2 n3 n4 n5 n6 T h c o u n t d o w n GS C2 n1 n2 To stop counting GSC N1 N2 N3 N4 N5 With counting down GS H n With counting up GS f n GS k n d k NUL GS w n GS n1 n2 n3 Before printing How to write program Printing on the roll paperProgram Descriptions Introduction Send Print Data GS H n Initialize printer again Printing bar codes RS-232C must be closed using this command Sample Program onto thermal paper Printing on label paper Sample Program onto thermal label paper Appendix a General Specifications Printing specificationsCharacters specifications Paper Thermal paper Near-end detector Thermal label paper Reliability Electrical characteristicsEMI by using Epson PS-130 External dimensions and weight Appendix B Connectors Signal Name Sender Appendix C Interfaces Specifications RS-232C compatible Serial interface timing Pin Number Signal Name Signal Direction FunctionPage Page International character set Command Name Appendix E Command Summary GS C2 GS C