Thermal label paper | Seiko Group TM-L60 guide

Paper width:	60 ±	mm
Roll size:	Roll	diameter		Max. ø83 mm
	Taken up paper roll width: 60 ±				mm
Specified paper:	Roll paper model No.:			NTP060-80
	(NAKAGAWA MFG. Co., Ltd.)
	[Original paper model No.:TFSOKS-E)
	(JUJO PAPER CO., LTD)]
Roll paper core:	Inside diameter: 12 mm
	Outside diameter: 18 mm
	Paper should never be pasted to the paper core.
4.2 Thermal label paper
Paper type:	Specified thermal label paper
Paper thickness:	143 ± 15 µm (total)
Form:	Roil	paper
Paper width:	60 ±	mm
Roll size:	Roll	diameter	Max. ø83 mm
	Taken up paper roll width: 60 ±				mm
Specified paper:	Thermal label paper:			NTLO60-80
	(NAKAGAWA MFG. Co., Ltd.)
	Original paper model No.: HD75 (JUJO
				PAPER CO., LTD)
Roll paper core:	Inside diameter:		12 mm
	Outside diameter:		22 mm
	Paper should never be pasted to the paper core.

NOTES: • Make sure that it can not be printed in 1.5 mm line spacing in the lower area of the label paper. (See 5-2 Printable Area and Label Paper Conditions)

•It is recommended to issue GS FF command to position the cutter to the base sheet of the label paper in order to cut the label paper easily.

•Make sure to issue FF or GS FF command just after sending data per label paper.

•Do not use other than specified paper.

5.Receive buffer

Either 4 K or 45 bytes is selectable by a DIP switch

63

Image 69

Seiko Group TM-L60 manual Thermal label paper

Contents

L 6 Page CC Class a FCC Compliance Statement for American Users Introduction Contents Appendix a General Specifications Setting UP Unpacking the Printer 1Checking the Contents of the Box Removing the Protective Material Choosing a Place for the Printer Part names 4Names and Functions of Parts Error red Power greenOperation panel Paper red Plugging in AC adapter Connecting the Power Supply to the Printer Connecting the interface cable Connecting the Host Computer to the Printer Installing the roll paper Installing the Roll Paper Paper Slot Adjusting the Paper-end Detector How to adjust the paper-end detectorPaper-end detector Page Setting the DIP Switches Locating the DIP switchesSetting the DIP switches DIP-Switch Functions DIP-switch Functions Baud Rate SelectionPrint Density Selection 1Checking Operation with the Self Test II. Reference 1Panel Switches and Commands Switches Power switchPaper-feed switch Printable Area and Label Paper Conditions Printable areaLabel paper Miscellaneous Notes Page Error LED red Error Correction Be inspected Error Display ON/OFF Timing Pattern Recovery Command Standby State Display Cleaning the head Cleaning the Head Cover-open Detector Removing Jammed PaperCover-open detector How to use this table Controlling the printer with commands Command Descriptions CommandsCommand descriptions XXX Command ESC ! n ESC SP n ESC $ n1 n2 ESC & s n m ap s Xam-n+l ESC % n = n 1 + 2 5 6 X n 2 m = 0 ESC * m n1 n2 d k Vertical Direction Horizontal Direction ESC = n ESC 3 n ESC D nkNUL ESC @ Range ESC E n ESC J n ESC G n ESC V n ESC R n ESC ¥ n1 n2 ESC nESC a n Position ESC c 4 n ESC p m n1 n2 ESC c 5 nESC d n ESC u n ESC t n ESC Journal near-end GS*n1n2dn1xn2x8 GS FF Dot Density GS/m GS a m n GS C 0 m n PER Feed switch or turning the power on GS Cl, GS C2, GS c, GS C GS C1 n1 n2 n3 n4 n5 n6 T h c o u n t d o w n GS C2 n1 n2 To stop counting GSC N1 N2 N3 N4 N5 With counting down GS H n With counting up GS f n GS k n d k NUL GS w n GS n1 n2 n3 Program Descriptions How to write program Printing on the roll paperIntroduction Before printing Send Print Data GS H n Initialize printer again Printing bar codes RS-232C must be closed using this command Sample Program onto thermal paper Printing on label paper Sample Program onto thermal label paper Appendix a General Specifications Printing specificationsCharacters specifications Paper Thermal paper Near-end detector Thermal label paper EMI by using Epson PS-130 Electrical characteristicsExternal dimensions and weight Reliability Appendix B Connectors Signal Name Sender Appendix C Interfaces Specifications RS-232C compatible Serial interface timing Pin Number Signal Name Signal Direction FunctionPage Page International character set Command Name Appendix E Command Summary GS C2 GS C