1Panel Switches and Commands | Seiko Group TM-L60 specification

Chapter 5 Cautions while Using

the Printer

5-1Panel Switches and Commands

nSwitches

(1) Power switch

[Function]	Turns the power supply on/off.
[Note]	• The RAM is initialized after turning off the circuit power supply.

•Do not touch the power supply switch during printing.

•When label paper is used, the printer automatically sets the la- bel at the starting position for printing just after turning the power switch on. When label paper is selected, the printer automati- cally detects label paper position and performs paper feeding. (Paper feed amount varies by the type of label paper.)

(2)Paper-feed switch

[Function]	If this switch is pressed, paper is fed one line based on the cur-
	rently specified line spacing. If this switch is held for 200 ms or
	more, paper is fed as long as the switch is pressed, and stops
	when the switch is released. If line spacing is set to 0, paper is
	fed while the switch is pressed.
	• The defined macro is executed when the switch is pressed in
	the macro executing command standby state.
	• Paper is fed by operating this switch, except during printing, in
	an error state, and in the macro executing command standby
	state.
	• When label is selected, paper feeding is performed in label units
	regardless of the predetermined paper feed amount.
	• Paper feeding is performed at the paper near-end state.
	• Pressing the PAPER FEED button recovers from waiting state
	of label ejection command (GS FF) execution or from self-test
	printing standby state.
[Note]	• Paper is not be fed when the printer cover is open.
	• The paper-feed switch can be enabled or disabled with ESC c5
	command. When this switch is disabled, you cannot feed paper
	with the switch.

16

Image 22

Seiko Group TM-L60 manual 1Panel Switches and Commands, Switches Power switch, Paper-feed switch

Contents

L 6 Page CC Class a FCC Compliance Statement for American Users Introduction Contents Appendix a General Specifications Setting UP 1Checking the Contents of the Box Unpacking the Printer Choosing a Place for the Printer Removing the Protective Material 4Names and Functions of Parts Part names Operation panel Power greenError red Paper red Connecting the Power Supply to the Printer Plugging in AC adapter Connecting the Host Computer to the Printer Connecting the interface cable Installing the Roll Paper Installing the roll paper Paper Slot How to adjust the paper-end detector Adjusting the Paper-end DetectorPaper-end detector Page Locating the DIP switches Setting the DIP SwitchesSetting the DIP switches Baud Rate Selection DIP-Switch Functions DIP-switch FunctionsPrint Density Selection 1Checking Operation with the Self Test II. Reference Switches Power switch 1Panel Switches and CommandsPaper-feed switch Printable area Printable Area and Label Paper ConditionsLabel paper Miscellaneous Notes Page Error Correction Error LED red Error Display Be inspected Command Standby State Display ON/OFF Timing Pattern Recovery Cleaning the Head Cleaning the head Removing Jammed Paper Cover-open DetectorCover-open detector Controlling the printer with commands How to use this table Commands Command DescriptionsCommand descriptions XXX Command ESC SP n ESC ! n ESC $ n1 n2 ESC % n ESC & s n m ap s Xam-n+l ESC * m n1 n2 d k = n 1 + 2 5 6 X n 2 m = 0 Vertical Direction Horizontal Direction ESC 3 n ESC = n ESC @ ESC D nkNUL ESC E n Range ESC G n ESC J n ESC R n ESC V n ESC n ESC ¥ n1 n2ESC a n ESC c 4 n Position ESC c 5 n ESC p m n1 n2ESC d n ESC t n ESC u n ESC Journal near-end GS FF GS*n1n2dn1xn2x8 GS/m Dot Density GS a m n PER Feed switch or turning the power on GS C 0 m n GS C1 n1 n2 n3 n4 n5 n6 GS Cl, GS C2, GS c, GS C GS C2 n1 n2 T h c o u n t d o w n GSC N1 N2 N3 N4 N5 To stop counting GS H n With counting down GS f n With counting up GS w n GS k n d k NUL GS n1 n2 n3 Introduction How to write program Printing on the roll paperProgram Descriptions Before printing Send Print Data Initialize printer again Printing bar codes GS H n RS-232C must be closed using this command Sample Program onto thermal paper Printing on label paper Sample Program onto thermal label paper Printing specifications Appendix a General SpecificationsCharacters specifications Near-end detector Paper Thermal paper Thermal label paper External dimensions and weight Electrical characteristicsEMI by using Epson PS-130 Reliability Appendix B Connectors Signal Name Sender Specifications RS-232C compatible Appendix C Interfaces Pin Number Signal Name Signal Direction Function Serial interface timingPage Page International character set Appendix E Command Summary Command Name GS C GS C2