Appendix E Command Summary, Command Name | Seiko Group TM-L60

APPENDIX E Command Summary

	Command	Name	Reference Page

	HT	Horizontal tab	26
	LF	Print and line feed	27
	FF	Print and position label to start printing	27
	ESC SP	Set character right-side spacing	27

	ESC	Set print mode	27
	ESC $	Set absolute position	28

	ESC %	Select/cancel user-defined character set	29

	ESC &	Define user-defined characters	29

	ESC *	Set bit image mode	30

	ESC 2	Set 1/6 inch line spacing	32

	ESC 3	Set line spacing using minimum units	32

	ESC =	Select device	32

	ESC @	Initialize printer	33

	ESC D	Set horizontal tab positions	33

	ESC E	Select emphasized mode	34

	ESC G	Select double-strike mode	35

	ESC J	Print and feed paper using minimum units	35

	ESC R	Select international character set	36
	ESC V	Set/cancel 90° cw rotated characters	36

	ESC ¥	Set relative position	37
	ESC -	Turn underline mode on/off	37
	ESC a	Align positions	37

	ESC c 4	Select paper detectors to stop printing	38
	ESC c 5	Enable/disable panel switches	39

	ESC d	Print and feed paper n lines	39
	ESC p	Generate pulse	39

Image 78

Seiko Group TM-L60 manual Appendix E Command Summary, Command Name

Contents

L 6 Page CC Class a FCC Compliance Statement for American Users Introduction Contents Appendix a General Specifications Setting UP 1Checking the Contents of the Box Unpacking the Printer Choosing a Place for the Printer Removing the Protective Material 4Names and Functions of Parts Part names Operation panel Power greenError red Paper red Connecting the Power Supply to the Printer Plugging in AC adapter Connecting the Host Computer to the Printer Connecting the interface cable Installing the Roll Paper Installing the roll paper Paper Slot Adjusting the Paper-end Detector How to adjust the paper-end detectorPaper-end detector Page Setting the DIP Switches Locating the DIP switchesSetting the DIP switches DIP-Switch Functions DIP-switch Functions Baud Rate SelectionPrint Density Selection 1Checking Operation with the Self Test II. Reference 1Panel Switches and Commands Switches Power switchPaper-feed switch Printable Area and Label Paper Conditions Printable areaLabel paper Miscellaneous Notes Page Error Correction Error LED red Error Display Be inspected Command Standby State Display ON/OFF Timing Pattern Recovery Cleaning the Head Cleaning the head Cover-open Detector Removing Jammed PaperCover-open detector Controlling the printer with commands How to use this table Command Descriptions CommandsCommand descriptions XXX Command ESC SP n ESC ! n ESC $ n1 n2 ESC % n ESC & s n m ap s Xam-n+l ESC * m n1 n2 d k = n 1 + 2 5 6 X n 2 m = 0 Vertical Direction Horizontal Direction ESC 3 n ESC = n ESC @ ESC D nkNUL ESC E n Range ESC G n ESC J n ESC R n ESC V n ESC ¥ n1 n2 ESC nESC a n ESC c 4 n Position ESC p m n1 n2 ESC c 5 nESC d n ESC t n ESC u n ESC Journal near-end GS FF GS*n1n2dn1xn2x8 GS/m Dot Density GS a m n PER Feed switch or turning the power on GS C 0 m n GS C1 n1 n2 n3 n4 n5 n6 GS Cl, GS C2, GS c, GS C GS C2 n1 n2 T h c o u n t d o w n GSC N1 N2 N3 N4 N5 To stop counting GS H n With counting down GS f n With counting up GS w n GS k n d k NUL GS n1 n2 n3 Introduction How to write program Printing on the roll paperProgram Descriptions Before printing Send Print Data Initialize printer again Printing bar codes GS H n RS-232C must be closed using this command Sample Program onto thermal paper Printing on label paper Sample Program onto thermal label paper Appendix a General Specifications Printing specificationsCharacters specifications Near-end detector Paper Thermal paper Thermal label paper External dimensions and weight Electrical characteristicsEMI by using Epson PS-130 Reliability Appendix B Connectors Signal Name Sender Specifications RS-232C compatible Appendix C Interfaces Pin Number Signal Name Signal Direction Function Serial interface timingPage Page International character set Appendix E Command Summary Command Name GS C GS C2