Operating the delegate units | Sennheiser SDC 8200 specs

Operating the components of the SDC 8200 system

Turning interconnected SDC 8200 CU central units on/off

When turning on a conference and interpretation system with several SDC 8200 CU central units, it is important that the central units are turned on in the correct order.

First turn on the “master” central unit.

Then turn on the “slave” central units in the order in which they are connected to the “master”.

To turn a central unit on:

Set the POWER switch to position “I”.

The consoles which are powered via this central unit are ready for oper- ation as soon as they are initialized.

The start display is shown on the LC display of this central unit.

>Volume =
P1	P2	P3	P4	P5	P6

Note!

It is, however, possible to simultaneously turn on interconnected cen- tral units via a switchable multiple socket.

To turn a central unit off:

Set the POWER switch to position “0”.

The display goes off. All consoles which were powered via this central unit are also turned off.

Note!

The central units are not disconnected from the mains when they are turned off. To disconnect the central units from the mains, pull their mains plugs out of the wall outlets.

Operating the delegate units

Taking the floor / Making a request to speak

In order to take the floor or make a request to speak, you have to press the

microphone key

. Depending on the conference mode chosen (1. to

10., see following section), you can either take the floor immediately or you have to wait until your microphone is turned on.

28

Image 28

Sennheiser system manual Operating the delegate units, Turning interconnected SDC 8200 CU central units on/off

Contents

SDC Thank you for choosing Sennheiser Contents Interconnecting several central units in master/slave mode 100 Important safety instructions Important safety information Disconnection from the mainsOverload Objects and liquids Replacement parts Maintenance and careSafety check SDC 8200 the digital conference and interpretation system Overview of the components SDC 8200 system Conference consoles Central units Interpreter consolesSDC 8200 CU central unit System cables Software controlSDC 8200 CU-M central unit SDC 8200 AO analog output unit Display of voting results as diagrams Technology used Components of the SDC 8200 system in detail All consoles featureConsoles Interpreter console features SDC 8200 D conference unit SDC 8200 C chairman unit SDC 8200 DC conference unit SDC 8200 CC chairman unit SDC 8200 DV conference unit Vote LED SDC 8200 CV chairman unit SDC 8200 ID interpreter console Autofloor LED SDC 8200 CU central unit SDC 8200 CU-M central unit SDC 8200 AO analog output unit optional System cables Turning the conference and interpretation system on/off Operating the components of the SDC 8200 systemTurning on the central unit for the first time Turning interconnected SDC 8200 CU central units on/off Operating the delegate unitsTaking the floor / Making a request to speak Direct Access mode Group 3 mode With request mode With Req. No clear mode Turning off the microphone / Cancelling a request to speak Hearing damage due to high volumes Voting Selecting an interpretation channelVote 1 Using the chip card slot of a conference console Operating the VIP units Turning all active conference consoles off priority Operating the chairman unitStarting a voting session Assigning a participant the speaking right Operating the interpreter consoles This system is capable of producing sound pressure Configuring the B-channel of an interpreter console Using the interpreter console Switching between the A-channel and the B-channel Adjusting the volume of the consoles’ built-in loudspeakers Operating the central unitMuting the microphone of the interpreter console Restarting the conference and interpretation system Menu operating controls F1, F2 and F3 function keysOperating Menu Control Level Working with the central unit’s operating menu Operating the components of the SDC 8200 system Interconnecting the conference/interpreter consoles Connecting cable strings to a central unitInterconnecting up to twelve SDC 8200 CU central units Structuring the SDC 8200 system Expansion stage 1 one central unit with up to 20 consoles =10 m RS 232 = 10 m Structuring an interpretation system Determining maximum cable lengthsCalculating the voltage drop on the system cables Selectable modes between or within interpreter booths Mode between booths MixedMode between booths Override Mode between booths Toggle Override Mode in booths Mixed Mode in booths Toggle OverrideAuto-floor function Example AUTO-FLOOR Connecting external audio sources Using external equipmentUsing the audio outputs of the central unit Setting up the SDC 8200 system Preparing the SDC 8200 system components for set upConference and interpreter consoles Central unit Setting up the SDC 8200 system Interconnecting the consoles Interconnecting the SDC 8200 system componentsConnecting a cable string to the central unit Activating the master/slave mode Exiting the slave mode of a central unit Connecting additional equipment Setting up remote conferences Connecting PA systems, recording units, etc Pin assignment of the 15-pole sub-D socket AUX OUT Load Connecting a PC to the central unit Configuring the SDC 8200 system Introduction to the central unit’s operating menuStart display Six main menus Exit Enter Submenus Menu part 1 Conference menu part 2 Submenus Menu part 3 Submenus of the Conference menu part 4 Submenus of the Conference Manual Init Submenus of the Conference menu part 6 Submenus of the Conference menu part Menu InterpretationPart 1of Submenus of the Interpretation menu part 2 Submenus of the Interpretation menu part 3 Submenus of the Interpretation menu part 4 Interpretation menu part Submenus of the Aux-In/Out menu part 1 Submenus of the Aux-In/Out menu part 2 Submenus of the Aux-In/Out menu part 3 Submenus of the Aux-In/Out menu part 4 Submenus of the Aux-In/Out menu part 5 Aux-In/Out Menu part 6 Submenus of the Aux-In/Out menu part 7 Submenus of the Aux-In/Out menu part 8 Submenus of the System menu Part 1 Submenus of the System menu part 2 Language and the License menu part 1 Setting the volume of the consoles’ built-in loudspeak- ers Configuring the conference systemAutomatically initializing all conference consoles Manually initializing all conference consoles Text Mic. Number = 00 is shown on the display Reserving a microphone number Selecting a conference mode Setting the speaker limit Adjusting the audio settings for the consoles’ microphones Configuring additional chairman units Chairmen Deleting the list of chairman units Chairmen Resetting the conference system Reset Configuring additional VIP units VIPDeleting the list of VIP units VIP Testing the consoles’ built-in loudspeakers Testing the consoles’ microphones Configuring the display of the voting options Configuring the interpretation systemWorking with the interpreter configuration Creating a new interpreter configuration Modifying the currently active interpreter configuration Loading a previously saved interpreter configuration Setting the max. number of interpreter booths/languages Setting the max. number of interpreter consoles per boothConfiguring the operating mode between booths Options Configuring the operating mode within a booth Configuring the language options for the interpreter booths Configuring the main target language A-channel of a booth Configuring the second target language B-channel of a booth Enabling the auto-relay interpretation function Auto-floor 100 101 Adding interpreter consoles to an existing configuration 102 103 Resetting the interpretation systemChoosing the audio inputs and outputs Adjusting the volume of the audio outputs 104 105 Assigning a channel to an audio output 106 Turning on/off the audio inputs or outputs Configuring the audio outputs for remote conferencing Adjusting the input level of an audio inputAdjusting the input sensitivity of an audio input 107 108 109 Making a system diagnosisDisplaying the current port status Configuring connected additional components 110Checking the communication within a cable string Turning on/off a camera control Configuring an ambient sound console 111 Software, language and license 112Choosing the language of the central unit’s operating menu Displaying the central unit’s serial number 113 If problems occur 114Central unit does not work Console does not work Accessories 115 Features of the central units Specifications116 117 118 AUX OUT RJ 45 cable SDC 8200 AO analog output unit119 Appendix a Camera control protocol Syntax of the commands120 121 CommandsNotation of the general syntax Appendix B Control panel protocol 122 123 1X06060606 Appendix C Repeater for the SDC 8200 system 124 Warranty regulations Manufacturer declarationsCE Declaration of Conformity FCC Rules 126