Manuals / Sennheiser / Musical Instruments & Equipment / Microphone

Sennheiser SDC 8200 system manual 108

Models: SDC 8200

1 128

Download 128 pages 11.95 Kb

Page 108

Configuring the SDC 8200 system

Aux In 1

2Sensitivity

Aux In 1

Sensitivity = HIGH Press ENTER to Save

From the central unit’s operating menu, choose “Aux-In/Out”.

Choose the desired audio input.

Choose “Sensitivity”.

The current input sensitivity (“LOW” or “HIGH”) is shown on the display.

–Choose “LOW” if the connected audio source delivers a strong signal (e.g. CD player).

–Choose “HIGH” if the connected audio source delivers a weak signal (e.g. microphone).

Adjust the input sensitivity and press the ENTER key to save your set- ting.

ON

1 2

	E	F		0	1	2
		F			1
D
							3
							3
							4
C							4
C							5
B

	A		9	8	7		6
					7

Configuring the outputs of the SDC 8200 AO analog output unit

You can configure the outputs of the SDC 8200 AO analog output unit via the two DIP switches and the rotary switch located on the printed circuit board of the SDC 8200 AO. For configuring the outputs, you have to open the analog output unit.

The two DIP switches and the rotary switch are located in the middle of the printed circuit board, directly behind the front panel.

Warning!

Danger of electric shock!

If you do not disconnect the analog output unit from the central unit before opening the SDC 8200 AO’s housing, you can receive an electric shock.

Disconnect the SDC 8200 AO from the central unit before configuring the SDC 8200 AO’s outputs!

With the two DIP switches (2 switch positions: ON or OFF) and the rotary

switch (16 switch positions: 1 to F), you assign a channel number to the output OUT 1 (reference output). The outputs OUT 2 to OUT 8 are auto- matically assigned the subsequent channel numbers.

The following table shows the possible switch positions and the resulting channel assignments:

DIP switches		Rotary	OUT 0	OUT 1	OUT 2	OUT 3	OUT 4	OUT 5	OUT 6	OUT 7	OUT 8
		switch
2	1	switch
2	1


OFF	OFF	0	0	0	1	2	3	4	5	6	7

OFF	OFF	1	0	1	2	3	4	5	6	7	8

OFF	OFF	2	0	2	3	4	5	6	7	8	9

OFF	OFF	...	0	...	...	...	...	...	...	...	...

OFF	OFF	F	0	15	16	17	18	19	20	21	22

(*)	ON	0	0	16	17	18	19	20	21	22	23

(*)	ON	1	0	17	18	19	20	21	22	23	24

(*)	ON	...	0	...	...	...	...	...	...	...	...

(*)	ON	4	0	20	21	22	23	24	25	26	27

(*)	ON	5	0	21	22	23	24	25	26	27	28

(*) can be set to position “ON” or “OFF”

108

Image 108

Sennheiser SDC 8200 system manual 108

Contents

SDC Thank you for choosing Sennheiser Contents Interconnecting several central units in master/slave mode 100 Important safety instructions Important safety information Disconnection from the mainsOverload Objects and liquidsMaintenance and care Replacement partsSafety check SDC 8200 the digital conference and interpretation system Overview of the components SDC 8200 system Conference consolesInterpreter consoles Central unitsSDC 8200 CU central unit System cables Software controlSDC 8200 CU-M central unit SDC 8200 AO analog output unitDisplay of voting results as diagrams Technology usedAll consoles feature Components of the SDC 8200 system in detailConsoles Interpreter console features SDC 8200 D conference unit SDC 8200 C chairman unit SDC 8200 DC conference unit SDC 8200 CC chairman unit SDC 8200 DV conference unit Vote LEDSDC 8200 CV chairman unit SDC 8200 ID interpreter console Autofloor LEDSDC 8200 CU central unit SDC 8200 CU-M central unit SDC 8200 AO analog output unit optional System cables Operating the components of the SDC 8200 system Turning the conference and interpretation system on/offTurning on the central unit for the first time Operating the delegate units Turning interconnected SDC 8200 CU central units on/offTaking the floor / Making a request to speak Direct Access mode Group 3 mode With request mode With Req. No clear modeTurning off the microphone / Cancelling a request to speak Hearing damage due to high volumesSelecting an interpretation channel VotingVote 1 Using the chip card slot of a conference console Operating the VIP unitsOperating the chairman unit Turning all active conference consoles off priorityStarting a voting session Assigning a participant the speaking right Operating the interpreter consoles This system is capable of producing sound pressureConfiguring the B-channel of an interpreter console Using the interpreter console Switching between the A-channel and the B-channelAdjusting the volume of the consoles’ built-in loudspeakers Operating the central unitMuting the microphone of the interpreter console Restarting the conference and interpretation systemF1, F2 and F3 function keys Menu operating controlsOperating Menu Control Level Working with the central unit’s operating menu Operating the components of the SDC 8200 system Interconnecting the conference/interpreter consoles Connecting cable strings to a central unitInterconnecting up to twelve SDC 8200 CU central units Structuring the SDC 8200 systemExpansion stage 1 one central unit with up to 20 consoles =10 m RS 232 = 10 m Determining maximum cable lengths Structuring an interpretation systemCalculating the voltage drop on the system cables Selectable modes between or within interpreter booths Mode between booths MixedMode between booths Override Mode between booths Toggle OverrideMode in booths Mixed Mode in booths Toggle OverrideAuto-floor function ExampleAUTO-FLOOR Using external equipment Connecting external audio sourcesUsing the audio outputs of the central unit Setting up the SDC 8200 system Preparing the SDC 8200 system components for set upConference and interpreter consoles Central unitSetting up the SDC 8200 system Interconnecting the SDC 8200 system components Interconnecting the consolesConnecting a cable string to the central unit Activating the master/slave mode Exiting the slave mode of a central unitConnecting additional equipment Setting up remote conferencesConnecting PA systems, recording units, etc Pin assignment of the 15-pole sub-D socket AUX OUTLoad Connecting a PC to the central unit Configuring the SDC 8200 system Introduction to the central unit’s operating menuStart display Six main menusExit Enter Submenus Menu part 1Conference menu part 2 SubmenusMenu part 3 Submenus of the Conference menu part 4 Submenus of the Conference Manual InitSubmenus of the Conference menu part 6 Submenus of the Conference menu part Interpretation MenuPart 1of Submenus of the Interpretation menu part 2 Submenus of the Interpretation menu part 3 Submenus of the Interpretation menu part 4 Interpretation menu part Submenus of the Aux-In/Out menu part 1 Submenus of the Aux-In/Out menu part 2 Submenus of the Aux-In/Out menu part 3 Submenus of the Aux-In/Out menu part 4 Submenus of the Aux-In/Out menu part 5 Aux-In/Out Menu part 6Submenus of the Aux-In/Out menu part 7 Submenus of the Aux-In/Out menu part 8 Submenus of the System menu Part 1Submenus of the System menu part 2 Language and the License menu part 1 Setting the volume of the consoles’ built-in loudspeak- ers Configuring the conference systemAutomatically initializing all conference consoles Manually initializing all conference consolesText Mic. Number = 00 is shown on the display Reserving a microphone number Selecting a conference mode Setting the speaker limitAdjusting the audio settings for the consoles’ microphones Configuring additional chairman units Chairmen Deleting the list of chairman units ChairmenConfiguring additional VIP units VIP Resetting the conference system ResetDeleting the list of VIP units VIP Testing the consoles’ built-in loudspeakers Testing the consoles’ microphonesConfiguring the interpretation system Configuring the display of the voting optionsWorking with the interpreter configuration Creating a new interpreter configuration Modifying the currently active interpreter configuration Loading a previously saved interpreter configurationSetting the max. number of interpreter booths/languages Setting the max. number of interpreter consoles per boothConfiguring the operating mode between booths OptionsConfiguring the operating mode within a booth Configuring the language options for the interpreter boothsConfiguring the main target language A-channel of a booth Configuring the second target language B-channel of a boothEnabling the auto-relay interpretation function Auto-floor 100 101 Adding interpreter consoles to an existing configuration 102Resetting the interpretation system 103Choosing the audio inputs and outputs Adjusting the volume of the audio outputs 104105 Assigning a channel to an audio output106 Turning on/off the audio inputs or outputsConfiguring the audio outputs for remote conferencing Adjusting the input level of an audio inputAdjusting the input sensitivity of an audio input 107108 Making a system diagnosis 109Displaying the current port status Configuring connected additional components 110Checking the communication within a cable string Turning on/off a camera controlConfiguring an ambient sound console 111Software, language and license 112Choosing the language of the central unit’s operating menu Displaying the central unit’s serial number113 If problems occur 114Central unit does not work Console does not workAccessories 115Specifications Features of the central units116 117 118 AUX OUTSDC 8200 AO analog output unit RJ 45 cable119 Syntax of the commands Appendix a Camera control protocol120 Commands 121Notation of the general syntax Appendix B Control panel protocol 122123 1X06060606Appendix C Repeater for the SDC 8200 system 124Warranty regulations Manufacturer declarationsCE Declaration of Conformity FCC Rules126