F1, F2 and F3 function keys | Sennheiser SDC 8200 instruction

Operating the components of the SDC 8200 system

>Lautstaerke =
P1	P2	P3	P4	P5	P6

>Lautstaerke =

P1 P2 P3 P4 P5 P6

The F1, F2 and F3 function keys

The F1 and F3 function keys serve to lock the central unit.

To lock the central unit:

Make sure that the start display appears as shown on the left. If the start display does not appear, press the EXIT key repeatedly until the start display appears.

Simultaneously press the F1 and F3 function keys and keeps them pressed for three seconds.

If you release the two function keys after three seconds, the “key”

symbol () appears in the lower right corner of the display. The operating menu of the central unit is locked and you cannot change the settings of your conference.

To unlock the central unit:

Simultaneously press the F1 and F3 function keys and keeps them pressed for three seconds.

If you release the two function keys after three seconds, the “key”

symbol () disappears from the lower right corner of the display. The operating menu of the central unit can be accessed at any time by pressing the ENTER key (see “Working with the central unit’s operating menu” on page 42), and you can change all settings of your confer- ence.

The menu operating controls

The jog wheel and the ENTER and EXIT keys on the central unit allow you to navigate through the central unit’s operating menu, to choose settings and to enter and change values.

	Operating	Menu	To
	control	level

		main menu	choose a menu item

	Jog wheel		choose a menu item
	Jog wheel	submenu	or
		submenu	or
			choose the desired setting

			activate a selected menu item
	ENTER key	main menu and	or
	ENTER key	submenu	save settings and return to the previous
			menu level

		main menu and	exit a menu item without saving the set-
	EXIT key	main menu and	tings and return to the previous menu
		submenu	level
			level

For a complete overview of all menus of the central unit, see “Introduction to the central unit’s operating menu” on page 60 to 84.

41

Image 41

Sennheiser SDC 8200 system manual F1, F2 and F3 function keys, Menu operating controls, Operating Menu Control Level

Contents

SDC Thank you for choosing Sennheiser Contents Interconnecting several central units in master/slave mode 100 Important safety instructions Disconnection from the mains Important safety informationOverload Objects and liquids Safety check Maintenance and careReplacement parts SDC 8200 the digital conference and interpretation system Conference consoles Overview of the components SDC 8200 system SDC 8200 CU central unit Interpreter consolesCentral units Software control System cablesSDC 8200 CU-M central unit SDC 8200 AO analog output unit Technology used Display of voting results as diagrams Consoles All consoles featureComponents of the SDC 8200 system in detail Interpreter console features SDC 8200 D conference unit SDC 8200 C chairman unit SDC 8200 DC conference unit SDC 8200 CC chairman unit Vote LED SDC 8200 DV conference unit SDC 8200 CV chairman unit Autofloor LED SDC 8200 ID interpreter console SDC 8200 CU central unit SDC 8200 CU-M central unit SDC 8200 AO analog output unit optional System cables Turning on the central unit for the first time Operating the components of the SDC 8200 systemTurning the conference and interpretation system on/off Taking the floor / Making a request to speak Operating the delegate unitsTurning interconnected SDC 8200 CU central units on/off Direct Access mode Group 3 mode With Req. No clear mode With request mode Hearing damage due to high volumes Turning off the microphone / Cancelling a request to speak Vote 1 Selecting an interpretation channelVoting Operating the VIP units Using the chip card slot of a conference console Starting a voting session Operating the chairman unitTurning all active conference consoles off priority Assigning a participant the speaking right This system is capable of producing sound pressure Operating the interpreter consoles Configuring the B-channel of an interpreter console Switching between the A-channel and the B-channel Using the interpreter console Operating the central unit Adjusting the volume of the consoles’ built-in loudspeakersMuting the microphone of the interpreter console Restarting the conference and interpretation system Operating Menu Control Level F1, F2 and F3 function keysMenu operating controls Working with the central unit’s operating menu Operating the components of the SDC 8200 system Connecting cable strings to a central unit Interconnecting the conference/interpreter consolesInterconnecting up to twelve SDC 8200 CU central units Structuring the SDC 8200 system Expansion stage 1 one central unit with up to 20 consoles =10 m RS 232 = 10 m Calculating the voltage drop on the system cables Determining maximum cable lengthsStructuring an interpretation system Mode between booths Mixed Selectable modes between or within interpreter boothsMode between booths Override Mode between booths Toggle Override Mode in booths Toggle Override Mode in booths MixedAuto-floor function Example AUTO-FLOOR Using the audio outputs of the central unit Using external equipmentConnecting external audio sources Preparing the SDC 8200 system components for set up Setting up the SDC 8200 systemConference and interpreter consoles Central unit Setting up the SDC 8200 system Connecting a cable string to the central unit Interconnecting the SDC 8200 system componentsInterconnecting the consoles Exiting the slave mode of a central unit Activating the master/slave mode Setting up remote conferences Connecting additional equipment Pin assignment of the 15-pole sub-D socket AUX OUT Connecting PA systems, recording units, etc Load Connecting a PC to the central unit Introduction to the central unit’s operating menu Configuring the SDC 8200 systemStart display Six main menus Exit Enter Menu part 1 Submenus Submenus Conference menu part 2 Menu part 3 Submenus of the Conference menu part 4 Manual Init Submenus of the Conference Submenus of the Conference menu part 6 Submenus of the Conference menu part Part 1of InterpretationMenu Submenus of the Interpretation menu part 2 Submenus of the Interpretation menu part 3 Submenus of the Interpretation menu part 4 Interpretation menu part Submenus of the Aux-In/Out menu part 1 Submenus of the Aux-In/Out menu part 2 Submenus of the Aux-In/Out menu part 3 Submenus of the Aux-In/Out menu part 4 Submenus of the Aux-In/Out menu part 5 Menu part 6 Aux-In/Out Submenus of the Aux-In/Out menu part 7 Submenus of the Aux-In/Out menu part 8 Part 1 Submenus of the System menu Submenus of the System menu part 2 Language and the License menu part 1 Configuring the conference system Setting the volume of the consoles’ built-in loudspeak- ersAutomatically initializing all conference consoles Manually initializing all conference consoles Text Mic. Number = 00 is shown on the display Reserving a microphone number Setting the speaker limit Selecting a conference mode Adjusting the audio settings for the consoles’ microphones Deleting the list of chairman units Chairmen Configuring additional chairman units Chairmen Deleting the list of VIP units VIP Configuring additional VIP units VIPResetting the conference system Reset Testing the consoles’ microphones Testing the consoles’ built-in loudspeakers Working with the interpreter configuration Configuring the interpretation systemConfiguring the display of the voting options Creating a new interpreter configuration Loading a previously saved interpreter configuration Modifying the currently active interpreter configuration Setting the max. number of interpreter consoles per booth Setting the max. number of interpreter booths/languagesConfiguring the operating mode between booths Options Configuring the language options for the interpreter booths Configuring the operating mode within a booth Configuring the second target language B-channel of a booth Configuring the main target language A-channel of a booth Enabling the auto-relay interpretation function Auto-floor 100 101 102 Adding interpreter consoles to an existing configuration Choosing the audio inputs and outputs Resetting the interpretation system103 104 Adjusting the volume of the audio outputs Assigning a channel to an audio output 105 Turning on/off the audio inputs or outputs 106 Adjusting the input level of an audio input Configuring the audio outputs for remote conferencingAdjusting the input sensitivity of an audio input 107 108 Displaying the current port status Making a system diagnosis109 110 Configuring connected additional componentsChecking the communication within a cable string Turning on/off a camera control 111 Configuring an ambient sound console 112 Software, language and licenseChoosing the language of the central unit’s operating menu Displaying the central unit’s serial number 113 114 If problems occurCentral unit does not work Console does not work 115 Accessories 116 SpecificationsFeatures of the central units 117 AUX OUT 118 119 SDC 8200 AO analog output unitRJ 45 cable 120 Syntax of the commandsAppendix a Camera control protocol Notation of the general syntax Commands121 122 Appendix B Control panel protocol 1X06060606 123 124 Appendix C Repeater for the SDC 8200 system Manufacturer declarations Warranty regulationsCE Declaration of Conformity FCC Rules 126