SELECTING A SPECIAL MODE

The procedure for selecting a special mode for fax is explained below.

The settings that must be selected vary for each special mode, however, the general procedure is the same. The procedure for erasing shadows at the edges of the image when sending a fax is explained below as an example.

The side to be scanned must be face up! 1 Place the originals.

When using the document glass, place the original with the side to be scanned face down.

Scan

 

Internet Fax

 

Fax

USB Mem. Scan

PC Scan

Address Book

Original

Scan:

A4

Send:

Auto

Direct TX

 

 

Exposure

 

 

Auto

 

 

 

 

 

 

 

 

 

 

Sub Address

 

Resolution

 

Standard

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Address Review

 

Special Modes

 

 

 

 

 

 

 

 

 

 

 

 

 

(1)

 

 

 

 

 

File

 

 

 

Quick File

Auto Reception

Fax Memory:100%

2 Select settings in the touch panel.

(1)Touch the [Special Modes] key.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fax/Special Modes

 

 

 

 

 

 

 

 

OK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Program

 

 

Erase

 

Timer

 

 

 

 

 

 

 

 

 

(2)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Slow Scan

1

 

 

 

 

Card Shot

 

 

 

 

2

 

 

 

 

 

 

 

 

 

Mode

 

 

 

 

 

 

 

 

 

 

Business

 

 

 

 

 

File

 

Quick File

 

 

 

 

 

 

 

Card Scan

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Transaction

 

 

 

 

 

Own Name

 

 

 

 

 

 

Report

 

 

 

 

 

Select

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fax/Special Modes

 

 

 

 

 

 

 

 

 

OK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(4)

 

Erase

 

 

 

 

 

 

 

Cancel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Edge

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Erase

 

 

 

 

Edge

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15

 

 

 

 

 

 

 

 

 

 

 

 

(0~20)

 

 

 

 

 

 

 

 

 

 

 

 

mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Side Erase

(3)

(2)Touch the [Erase] key.

The erase settings will be configured to erase a width of

15 mm around the edges of the original.

(3)Set the erasure width to 15 mm with the keys.

The erase area is set to "Edge Erase" by default.

A particular side can be erased by touching the [Side Erase] key and selecting settings for that side.

(4) Touch the [OK] key.

94

Page 96
Image 96
Sharp MX-C311, MX-C381 Touch the Special Modes key, Touch the Erase key, Set the erasure width to 15 mm with the keys