Computer Image Adjustment (“SIG-ADJ” Menu)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pict.

 

SIG-ADJ

 

SCR

 

PRJ

 

Net.

 

 

 

Clock

 

 

 

0

 

 

 

 

 

 

 

 

 

 

Phase

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H-Pos

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V-Pos

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Reset

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Resolution

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Auto Sync

 

 

 

 

On

 

 

 

 

 

 

Signal Type

 

 

 

 

Auto

 

 

 

*

 

 

Video Setup

 

 

 

 

0IRE

 

 

 

 

 

Dynamic Range

 

 

 

Auto

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Signal Info : 1080P

 

 

 

 

 

 

 

 

 

 

H : XX.X

kHz/

 

 

V : XX.X

Hz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SEL./ADJ.

 

 

 

 

ENTER

 

 

 

 

 

 

RETURN

 

 

 

 

 

END

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

* Displayed when the input mode is HDMI input.

Menu operation n Page 42

Setting the Resolution

Ordinarily, the type of input signal is detected and the correct resolution mode is automatically selected. However, for some signals, the optimal resolution mode in “Resolution” in the “SIG- ADJ” menu may need to be selected to match the computer display mode.

Note

Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering may occur, making the image hard to see.)

Information on the currently selected input signal can be confi rmed in item 7 on page 50.

Adjusting the Computer Image

Use the SIG-ADJ function in case of irregularities such as vertical stripes or flickering in portions of the screen.

Selectable

Description

items

 

 

 

Clock

Adjusts vertical noise.

Phase

Adjusts horizontal noise (similar to

 

tracking on your VCR).

H-Pos

Centers the on-screen image by

 

moving it to the left or right.

V-Pos

Centers the on-screen image by

 

moving it up or down.

Note

You can automatically adjust the computer image by setting “Auto Sync” in the “SIG-ADJ” menu to “On”, or pressing AUTO SYNC on the remote control.

Depending on the type of input signal, the adjustment range for each setting may vary or the adjustment may not be available at all.

To reset all adjustment items, select “Reset” and press ENTER.

Auto Sync (Auto Sync Adjustment)

Selectable

Description

items

 

On

Auto Sync adjustment will occur when

 

the projector is turned on or when the

 

input signals are switched, when con-

 

nected to a computer.

Off

Auto Sync adjustment is not

 

automatically performed.

Note

Auto Sync adjustment is also performed by pressing AUTO SYNC on the remote control.

When setting “Auto Sync” to “Off”, and if AUTO SYNC is pressed, Auto Sync will be executed in “On” mode. If the button is pressed again within one minute, Auto Sync will be executed in “On” mode.

The Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the projector.

When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments.

Features

Useful

49

Page 51
Image 51
Sharp XV-Z30000 appendix Computer Image Adjustment SIG-ADJ Menu, Setting the Resolution