Troubleshooting

 

Problem

 

Check

Page

 

 

 

 

 

 

 

 

 

ξ

Projector power cord is not plugged into the wall outlet.

27

 

 

 

 

 

 

 

 

 

ξ

Power to the external connected devices is off.

 

 

 

 

 

 

 

 

 

ξ

The selected input mode is wrong.

35

 

 

 

 

 

 

 

 

 

 

 

 

ξ

Cables are incorrectly connected to the projector.

23-27

 

 

 

 

 

 

 

 

 

ξ

Remote control battery has run out.

16

 

 

 

 

 

 

 

 

 

ξ

External output has not been set when connecting notebook com-

 

 

 

 

puter.

 

No picture or projector

 

 

ξ

The lamp unit cover is not installed correctly.

79, 80

 

does not start

 

 

 

 

 

 

 

ξ

The selected “Signal Type” is wrong.

50

 

 

 

 

 

 

 

 

 

ξ

“Bright” is set to minimum position.

45

 

 

 

 

 

 

 

 

 

ξ

Image adjustments are incorrectly set.

45

 

 

 

(COMPONENT, COMPUTER/COMPONENT or HDMI1, 2 input)

50

 

 

 

ξ

Input signal type is incorrectly set.

 

 

 

 

 

 

Color is faded or poor.

 

 

 

 

 

 

 

 

 

 

 

 

ξ

Adjust the focus.

30

 

 

 

 

 

 

 

 

 

ξ

The projection distance exceeds the focus range.

21

 

 

 

 

 

 

 

 

 

(Computer input)

49

 

 

 

ξ

Perform “SIG-ADJ” Adjustments (“Clock” and “Phase” Adjustment)

 

 

 

ξ

Noise may appear depending on the computer.

 

 

 

ξ

The “DNR” (Digital Noise Reduction) or “MNR” (Mosquito Noise Re-

48

 

 

 

 

duction) setting is not correct.

 

 

Picture is blurred;

ξ

There is fog on the lens. If the projector is carried from a cold room into

 

 

a warm room, or if it is suddenly heated, condensation may form on the

 

 

noise appears.

 

 

 

 

surface of the lens and the image will become blurred. Please set up the

 

 

 

 

 

 

 

 

 

 

projector at least one hour before it is to be used. If condensation should

 

 

 

 

 

form, remove the power cord from the wall outlet and wait for it to clear.

 

An unusual sound is

ξ

If the picture is normal, the sound is due to cabinet shrinkage

 

occasionally heard

 

caused by a room temperature changes. This will not affect opera-

 

 

from the cabinet.

 

tion or performance.

 

 

Maintenance

ξ

See “Maintenance Indicators”.

76

 

indicator on the

 

 

 

projector illuminates.

 

 

 

Picture is green when

ξ

Change the input signal type setting.

50

 

receiving YPbPr

 

 

 

signals and the video

 

 

 

equipment is connected

 

 

 

 

to the Component

 

 

 

 

(YPB(CB)PR(CR))

 

 

 

 

or COMPUTER/

 

 

 

COMPONENT terminal

 

 

 

 

on the projector.

 

 

 

Picture is pink when re-

 

 

 

ceiving RGB signals and

 

 

 

the video equipment is

 

 

 

connected to the Com-

 

 

 

ponent (YPB(CB)PR(CR))

 

 

 

 

or COMPUTER/

 

 

 

COMPONENT terminal

 

 

 

 

on the projector.

 

 

 

Appendix

83

Page 85
Image 85
Sharp XV-Z30000 appendix Troubleshooting, 23-27