Step by step | Sony 500 manual

More functions/services

Step by step

Using system functions from outside

DISA (direct inward system access)

If configured (contact your service personnel), you can use an external phone like an internal station to set up an outgoing external connection via the system. You can also activate or deactivate the following system functions:

•Reset services and functions, code #0 Æ page 78

•Call forwarding, code *1/#1 Æ page 28

•Lock and unlock phone, code *66/#66 Æ page 69

•Save your PIN,

code *93 Æ page 71

•Send a message,

code *68/#68 Æ page 73

•Leave an advisory message, code *69/#69 Æ page 75

•Ringing group, code *81/#81 Æ page 86

•Group call, code *85/#85 Æ page 86

•Caller ID suppression, code *86/#86 Æ page 67

•Camp-on tone, code *87/#87 Æ page 47

•Open door, code *61 Æ page 35

•Release door opener, code *89/#89 Æ page 36

•Control relays, code *90/#90 Æ page 84

•Do not disturb, code *97/#97 Æ page 66

•Ringer cutoff, code *98/#98 Æ page 65

•Dial using speed dial, code *7 Æ page 42

•Associated service, code *83 Æ page 79

Prerequisite: Your phone supports tone dialing (DTMF) or you can switch your phone to tone dialing. The phone is not connected to the system.

jEstablish a connection to the system. Enter the station number (contact your service personnel).

jWait for the continuous tone (if necessary, switch pho- ne to tone dialing) and enter the internal number assig- ned to you and the corresponding PIN.

( Enter the code (only required if programmed in the sys- tem).

80

Image 80

Sony 500 manual Step by step

Contents

Documentation Important information Trademarks Location of the telephone Product support on the Internet Contents Enhanced phone functions Displaying and assigning call charges Using team functions Testing the phoneSpecial functions in the LAN Not for HiPath 500 About this manual ServiceGeneral information Speakerphone quality and display legibility Intended useTelephone type Properties of your OpenStage 15 T Getting to know your OpenStage phoneUser interface of your OpenStage 15 T OpenStage Key Module Keys Audio keysMailbox key and Menu key Navigation keys Programmable function keys Meaning of LED displays on function keys Keypad Idle menu Idle modeDisplay Voicemail MailboxMessages Caller list Busy Program/Service menu Program/Service Answering a call via the handset Basic functionsAnswering a call Suggestions for using speakerphone mode Ending a call Mode Switching to speakerphone modeSwitching to the handset Activating Deactivating Making calls Off-hook dialingOn-hook dialing Dialing with DDS keys Displaying and dialing saved station numbers Redialing a numberEnding a call Reject calls Turning the microphone on and off Switching to the held party alternating Calling a second party consultationReturn to the first party Combine the calling parties into a three-party con- ference Transferring a call Deactivating call forwarding Using variable call forwardingCall forwarding Using call forwarding no reply Cfnr Deactivating call forwarding no reply Step by step Accepting a callback Using callbackStoring a callback Ending retrieval Viewing and deleting a stored callbackDeleting a displayed entry Enhanced phone functions Answering calls Using the speakerphone Enabling and disabling handsfree answerback Speaking to visitors via the entrance telephone Opening the door with a code at the door Activating the door opener Deactivating the door opener Canceling en-bloc sending En-bloc sending/correcting numbersDialing entered/displayed numbers Correcting numbers entered Using the caller list Retrieving the caller listDisplaying the call time Dialing a station number from the caller list Dialing a number from the internal directory Entry you wish to dial appears on the screen Using the Ldap directory not for HiPath If too many names are found Result is displayedIf no name is found Making calls using system speed-dial numbers Configure a speed-dial keyDialing with speed-dial keys Suffix-dialing Talking to your colleague with a speaker call If you make a mistake Automatic connection setup hotline Assigning a station number not for U.S Associated dialing/dialing aid Dialing aid on the S0 busDialing aid at the a/b T/R port Dialing aid from your telephone for another tele- phone Using call waiting second call During a callEnding the first call and answering the waiting call Ending the second call and resuming the first one Saving a number Preventing and allowing call waiting automatic camp-onTurning the call waiting tone on and off Parking a call Retrieving a parked call Conducting a conference If the second party does not answerAdding up to five parties to a conference Viewing the conference parties Removing the Isdn central office party from the conference Leaving a conferenceEnding a conference Activating tone dialing/DTMF suffix-dialing Consult? 80=Speaker call? Transfer? Send trunk flash not for HiPath Busy override joining a call in progress If you cannot reach a destinationCall waiting camp-on Using night answer Example Programming the Shift key Configuring function keysProgramming the function keys Overview of functions Saved function LED messages Trunk group key Programming a procedure key Step by step Configuring repdial keys Deleting function key programming For all calls and for the last call Displaying and assigning call chargesFor the current call Dialing with call charge assignment Privacy/security Turning ringer cutoff on and off Activating/deactivating Do not disturb Caller ID suppression Silent Monitoring/Secret busy override not for HiPath Monitoring a room Activating the telephone to be monitoredDeactivating the telephone to be monitored Monitoring the room Unlocking the phone Locking the telephone to prevent unauthorized useLocking the phone Locking another telephone to prevent unauthorized use Saving your PIN More functions/services Appointments functionSaving appointments Deleting and checking a saved appointment Creating and sending a message Using timed remindersSending a message Viewing and editing incoming messages Displaying and deleting messages you have sentViewing the transmission time Calling the sender Leaving an advisory message Deleting advisory messages Using another telephone like your own for a call Change number exchanged phone/ move/relocate Select and confirm the option shown Activating functions for another telephone Step by step Using functions in Isdn via code dialing keypad dialing Inputs in en-bloc mode Inputs in online mode Communicating with PC applications over a Csta interface Ending communication with the application Sensors HiPath 33x0/35x0 only Controlling relays only for HiPath Answering the page from the nearest telephone Paging persons not for U.S., not for HiPathPaging persons Using team functions Activating/deactivating a group callYou are part of a hunt group or call group You belong to multiple groups Step by step Removing all telephones in a call ringing group Accepting a call for another member of your teamRinging group Logging on and off during your shift Uniform Call Distribution UCDLogging on and off at the beginning and end of your shift Display the number of waiting calls Turning the night service on and off for UCDRequesting and activating a work time Special functions in the LAN not for HiPath Leaving hunt group/group call Setting up follow me call forwarding Night answer on? Save? Night answer off? Ringing group =or j Opening a door Individual phone configuration Setting contrast Adjusting audio settings Adjusting the receiving volume during a callAdjusting the ring volume Adjusting the ring tone Activating/deactivating the ringer Adjusting the speakerphone to the room acousticsLanguage for system functions Testing the phone Phone functions, testing Differing display view in a HiPath Fixing problems Responding to error messagesContact partner in the case of pro- blems Possible causes Troubleshooting Caring for your telephone Labeling keys Index Deleting 106 107 108 Overview of functions and codes UCD 110 111 112 Siemens Enterprise Communications