Extended Menu

Menu Setup 6 Chapter

 

 

 

Menu items in the 500s, relating to tape protection

Item number

Item name

 

Settings

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

501

STILL TIMER

 

Select the time delay from the tape transport stopping (either the STOP mode or the still

 

 

 

playback mode in search mode) until the unit automatically switches to the tape

 

 

 

protection mode, in order to protect the rotary heads and the tape.

 

 

 

0.5S...

 

 

 

 

 

..5M: Set the value in the range 0.5 seconds to 5 minutes.

 

 

 

 

 

1M

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note

 

 

 

If the value is set to 1 minute or more, the unit enters internal protection mode in 1

 

 

 

minute, which makes start up slower.

 

 

 

 

 

502

TAPE

 

Select the operation of the protection mode to protect the rotary heads and tape when in

 

PROTECTION

 

the still playback mode in search (jog/shuttle) mode.

 

MODE FROM

 

 

: Step forward at 1/30 normal speed at the time interval set with STILL TIMER.

 

 

STEP

 

SEARCH

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STDBY: Switch to Standby OFF mode (the unit not on standby).

 

 

 

 

 

 

 

 

 

 

 

 

Note

 

 

 

The STEP setting is enabled only when menu item 501 is set to less than 1 minute.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Menu items in the 600s, relating to the time code generator

 

 

 

 

 

 

 

 

 

 

 

 

 

Item number

Item name

 

Settings

 

 

 

 

 

 

 

 

 

 

 

 

 

601

VITC POSITION

 

For DSR-2000A

 

SEL-1

 

Select a line to insert the VITC in.

 

 

 

 

 

 

12H ...

 

 

 

 

... 20H: Select any line from 12 to 20.

 

 

 

 

16H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note

 

 

 

You can insert the VITC signal in two places. To insert it in two places, set both items

 

 

 

601 and 602.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

For DSR-2000AP

 

 

 

Select a line to insert the VITC in.

 

 

 

9H ...

 

 

 

 

... 22H: Select any line from 9 to 22.

 

 

 

19H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note

 

 

 

You can insert the VITC signal in two places. To insert it in two places, set both items

 

 

 

601 and 602.

 

 

 

 

 

 

 

 

 

 

 

602

VITC POSITION

 

For DSR-2000A

 

SEL-2

 

Select a line to insert the VITC in.

 

 

 

 

 

 

12H ...

 

 

... 20H: Select any line from 12 to 20.

 

 

 

18H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note

 

 

 

You can insert the VITC signal in two places. To insert it in two places, set both items

 

 

 

601 and 602.

 

 

 

 

 

 

 

 

 

 

 

 

For DSR-2000AP

 

 

 

Select a line to insert the VITC in.

 

 

 

9H ...

 

 

... 22H: Select any line from 9 to 22.

 

 

 

21H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note

 

 

 

You can insert the VITC signal in two places. To insert it in two places, set both items

 

 

 

601 and 602.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

116 Chapter 6 Setup Menu