Visca | Sony HD 3CCD instruction

Connecting a Monitor, etc. Equipped with the Analog Component (YPbPr) Input Connector

Connecting a Device Equipped with VISCA RS-232C Connector

Connections with the VISCA RS-232C cables (cross type) enable control of multiple cameras with a single RM-BR300 Remote Control Unit.

Installation and Connections

to AC outlet

RGB/COMPONENT

Connecting cable with D-sub 15-pin connectors (commercially available)

to component video input

HD video monitor, etc.

RM-BR300 Remote Control Unit

VISCA RS-232C to AC outlet

RS-232C cable (supplied with the

RM-BR300)

VISCA

RS-232C IN

to AC outlet

First BRC-H700

VISCA RS-232C OUT

RS-232C cable

VISCA RS-232C IN

to AC outlet

Second BRC-H700

VISCA RS-232C OUT

RS-232C cable

VISCA RS-232C IN

to AC outlet

Third to Seventh BRC-H700

56

Connections

Image 56

Sony HD 3CCD operating instructions Visca

Contents

HD 3CCD Color Video Camera Owner’s Record For customers in the U.S.AFor the customers in Canada Pour les utilisateurs au Canada Table of Contents Installation and Connections Appendix Precautions Typical CCD Phenomena Features Built-in interface card slotLong-distance image transmission and pan/tilt/zoom control Visca camera protocol supported Supplied Components and Accessories Mounted circuit board using lead-free solderSystem Components External video sync function Remote commander RM-BR300 Remote Control UnitOptional Products BRU-H700 HD Optical Multiplex Unit Video Switcher commercially available HFBK-SD1 SD Interface BoardHFBK-HD1 HD Interface Board HFBK-TS1 HDV Interface Board This system allows you System ConfigurationSystem configuration Overview System Configuration Operating a BRC-H700 Camera from a Long Distance Operating Multiple BRC-H700 Cameras from a Long Distance CCFC-M100HG Transmitting Audio Signals Using the BRU-H700 CCFC-M100HG BRBK-H700 HD HFBK-TS1 HDV HD video monitor Microphone Location and Function of Parts CameraFront Rear Setting of the Bottom switches Bottom Remote Commander supplied RM-BR300 Remote Control Unit not supplied Installing batteriesLock button and indicator Mode button When the menu of the camera is not displayed When the menu of the camera is displayed Mode selector Visca RS-232C connectorVisca RS-422 connector TALLY/CONTACT connector BRU-H700 HD Optical Multiplex Unit not supplied HFBK-SD1 SD Interface Board not supplied HFBK-HD1 HD Interface Board not supplied BRBK-H700 HD Optical Multiplex Card not supplied HFBK-XG1 XGA Interface Board not suppliedHFBK-TS1 HDV Interface Board not supplied Main Menu Setting MenusAbout On-Screen Menus Menu Operation Using the Supplied Remote Commander Operation Through MenusTo return to the main menu To return to the normal display 4,5 Spot Light Exposure MenuBack Light Using the ND Filter White Balance white balance modeWhen ONE Push is selected Color Menu Picture Menu Black and white mode Mode focus modeFocus Menu Color BAR Setting range of PAN LEFT/PAN Right Setting range of Tilt DOWN/TILT UPPAN Tilt Zoom Menu Ramp Curve Sync Master System MenuAnalog OUT Status Menu Down Converter MenuSUB OUT1 ADD Sync HD-SDI Menu PC-OUTPUT MenuSync VD Sync Audio Delay HDV Menu Panning and Tilting Turning on the PowerPan/Tilt and Zoom Operation If the Standby lamp of the camera flashes Operating Multiple Cameras with the Remote CommanderZooming Adjusting the Camera Focusing on a SubjectShooting with Back Lighting To focus the camera on a subject automatically To recall the stored settings To cancel the preset memory To assign camera addresses automatically To illuminate the panel of the Remote Control UnitOperating Multiple Cameras Direction REV 1STD PAN-TILT Reset To assign camera addresses manually Turn the dial on the upper part of the joystick Adjusting the White Balance One-push auto focusing during manual focus adjustmentTo adjust the white balance automatically To adjust the white balance manually Functions of the R and B controls Adjusting the BrightnessFunctions of the Value and Bright controls Storing Camera Settings To select positions 9 to Setting the Speed of the Camera Moving to a Preset Position Installation Removing/Attaching the Cable CoverAttaching an Interface Board To remove the cable cover Installing the Camera To install the camera on a deskTo remove the interface board To attach the camera to a tripod Installation example Installing the Camera on the CeilingBefore installation Attachment materials Ceiling Hole Ceiling bracket B To remove the camera Connecting to an AC OutletConnections Connecting the RM-BR300 Remote Control Unit Visca Connecting a Device Equipped with Visca RS-422 Connector Monitor HFBK-SD1 SD Connecting a VTR Equipped with SDI Input Connector Connecting a VTR Equipped with HD-SDI Input Connectors Connecting a Computer Connecting the BRU-H700 HD Optical Multiplex Unit Connecting a Video Switcher Cable Second BRC To connect a single camera Connecting a Sync Signal GeneratorTo connect multiple cameras to the HD sync signal generator To connect multiple cameras to the SD sync signal generator Sync Indicators on the BRC-H700 camera Error messages for the BRU-H700 HD Optical Multiplex UnitList of Messages Messages for the BRC-H700 camera Troubleshooting Symptom Cause Remedy Symptom Cause Remedy Menu Configuration Speed STD RGB Presetting Items Presetting menu items SUB OUT ADD Sync IMG Size Specifications Input/output connectorsSupplied accessories System Dimensions BRC-H700 Video CameraCeiling Bracket B Top Side RM-BR300 Remote Control Unit Top BRU-H700 HD Optical Multiplex Unit Top Front Side Visca RS-422 connector connector plug 9-pin Visca RS-232C in connector mini-DIN 8-pin, femaleVisca RS-232C OUT connector mini DIN 8-pin, female Pin Assignments RM-BR300 Remote Control Unit optional BRU-H700 HD Optical Multiplex Unit optional Pin Visca RS-232C OUT connector mini DIN 8-pinFemale Second BRC-H700 or BRU-H700 Wiring Diagram of Visca RS-422 ConnectionThird to Seventh BRC-H700 or BRU-H700 Using the Visca RS-422 Connector Plug To remove the connector plug