Connecting a Sync Signal Generator | Sony HD 3CCD specification

Connecting a Sync Signal

Generator

To connect a single camera

75-ohm termination switch: ON

to AC outlet

EXT SYNC IN

75-ohm coaxial cable

	Installation	to SYNC OUT
		Sync signal generator
	and Connections

To connect multiple cameras to the HD sync signal generator

You can connect up to seven cameras.

Third to Seventh (last)

BRC-H700

		75-ohm termination
		switch: ON
		to AC outlet
		EXT SYNC IN
		Second BRC-H700
		75-ohm termination
	availableCommercially separatorsignaltype-T	switch: OFF
	availableCommercially separatorsignaltype-T	to AC outlet
		to AC outlet
		EXT SYNC IN
		First BRC-H700
		75-ohm termination
		switch: OFF
		to AC outlet
		EXT SYNC IN
		75-ohm coaxial cable
		to SYNC OUT
		HD sync signal generator

62

Connections

Image 62

Sony HD 3CCD operating instructions Connecting a Sync Signal Generator, To connect a single camera

Contents

HD 3CCD Color Video Camera For the customers in Canada Owner’s RecordFor customers in the U.S.A Pour les utilisateurs au Canada Table of Contents Installation and Connections Appendix Precautions Typical CCD Phenomena Long-distance image transmission and pan/tilt/zoom control FeaturesBuilt-in interface card slot Visca camera protocol supported System Components Supplied Components and AccessoriesMounted circuit board using lead-free solder External video sync function Optional Products Remote commanderRM-BR300 Remote Control Unit BRU-H700 HD Optical Multiplex Unit HFBK-HD1 HD Interface Board Video Switcher commercially availableHFBK-SD1 SD Interface Board HFBK-TS1 HDV Interface Board This system allows you System ConfigurationSystem configuration Overview System Configuration Operating a BRC-H700 Camera from a Long Distance Operating Multiple BRC-H700 Cameras from a Long Distance CCFC-M100HG Transmitting Audio Signals Using the BRU-H700 CCFC-M100HG BRBK-H700 HD HFBK-TS1 HDV HD video monitor Microphone Front Location and Function of PartsCamera Rear Setting of the Bottom switches Bottom Remote Commander supplied Lock button and indicator RM-BR300 Remote Control Unit not suppliedInstalling batteries Mode button When the menu of the camera is not displayed When the menu of the camera is displayed Visca RS-422 connector Mode selectorVisca RS-232C connector TALLY/CONTACT connector BRU-H700 HD Optical Multiplex Unit not supplied HFBK-SD1 SD Interface Board not supplied HFBK-HD1 HD Interface Board not supplied BRBK-H700 HD Optical Multiplex Card not supplied HFBK-XG1 XGA Interface Board not suppliedHFBK-TS1 HDV Interface Board not supplied Main Menu Setting MenusAbout On-Screen Menus To return to the main menu Menu Operation Using the Supplied Remote CommanderOperation Through Menus To return to the normal display 4,5 Spot Light Exposure MenuBack Light When ONE Push is selected Using the ND FilterWhite Balance white balance mode Color Menu Picture Menu Focus Menu Black and white modeMode focus mode Color BAR PAN Tilt Zoom Menu Setting range of PAN LEFT/PAN RightSetting range of Tilt DOWN/TILT UP Ramp Curve Sync Master System MenuAnalog OUT SUB OUT1 Status MenuDown Converter Menu ADD Sync Sync VD HD-SDI MenuPC-OUTPUT Menu Sync Audio Delay HDV Menu Panning and Tilting Turning on the PowerPan/Tilt and Zoom Operation If the Standby lamp of the camera flashes Operating Multiple Cameras with the Remote CommanderZooming Shooting with Back Lighting Adjusting the CameraFocusing on a Subject To focus the camera on a subject automatically To recall the stored settings To cancel the preset memory To assign camera addresses automatically To illuminate the panel of the Remote Control UnitOperating Multiple Cameras Direction REV 1STD PAN-TILT Reset To assign camera addresses manually Turn the dial on the upper part of the joystick To adjust the white balance automatically Adjusting the White BalanceOne-push auto focusing during manual focus adjustment To adjust the white balance manually Functions of the R and B controls Adjusting the BrightnessFunctions of the Value and Bright controls Storing Camera Settings To select positions 9 to Setting the Speed of the Camera Moving to a Preset Position Attaching an Interface Board InstallationRemoving/Attaching the Cable Cover To remove the cable cover To remove the interface board Installing the CameraTo install the camera on a desk To attach the camera to a tripod Installation example Installing the Camera on the CeilingBefore installation Attachment materials Ceiling Hole Ceiling bracket B To remove the camera Connecting to an AC OutletConnections Connecting the RM-BR300 Remote Control Unit Visca Connecting a Device Equipped with Visca RS-422 Connector Monitor HFBK-SD1 SD Connecting a VTR Equipped with SDI Input Connector Connecting a VTR Equipped with HD-SDI Input Connectors Connecting a Computer Connecting the BRU-H700 HD Optical Multiplex Unit Connecting a Video Switcher Cable Second BRC To connect a single camera Connecting a Sync Signal GeneratorTo connect multiple cameras to the HD sync signal generator To connect multiple cameras to the SD sync signal generator Sync List of Messages Indicators on the BRC-H700 cameraError messages for the BRU-H700 HD Optical Multiplex Unit Messages for the BRC-H700 camera Troubleshooting Symptom Cause Remedy Symptom Cause Remedy Menu Configuration Speed STD RGB Presetting Items Presetting menu items SUB OUT ADD Sync IMG Size Supplied accessories SpecificationsInput/output connectors System Ceiling Bracket B DimensionsBRC-H700 Video Camera Top Side RM-BR300 Remote Control Unit Top BRU-H700 HD Optical Multiplex Unit Top Front Side Visca RS-232C OUT connector mini DIN 8-pin, female Visca RS-422 connector connector plug 9-pinVisca RS-232C in connector mini-DIN 8-pin, female Pin Assignments RM-BR300 Remote Control Unit optional BRU-H700 HD Optical Multiplex Unit optional Pin Visca RS-232C OUT connector mini DIN 8-pinFemale Second BRC-H700 or BRU-H700 Wiring Diagram of Visca RS-422 ConnectionThird to Seventh BRC-H700 or BRU-H700 Using the Visca RS-422 Connector Plug To remove the connector plug