System Components, External video sync function

External video sync function

The camera is equipped with an external video sync function to synchronize the camera images on multiple cameras. The camera also has an analog component/ RGB output connector as standard equipment.

Tally lamp

The tally lamp of the camera allows you to make sure it is selected at a glance.

Mounted circuit board using lead-free solder

Lead-free solder is used for the circuit boards of the camera for environmental reasons.

System Components

In order to support multiple system configurations, a variety of optional products are available for the BRC- H700 HD 3CCD Color Video Camera. This section introduces these optional products as well as the accessories supplied with the camera.

Supplied Components and Accessories

Before using the camera, make sure you have the following components and accessories supplied.

Camera (1)

AC power adaptor MPA-AC1 (Sony) (1)

AC power cord (1)

USA and Canadian model

Overview

System Components

Page 7

Image 7

Sony HD 3CCD System Components, Supplied Components and Accessories, External video sync function, Tally lamp

Contents

HD 3CCD Color Video Camera Pour les utilisateurs au Canada Owner’s RecordFor customers in the U.S.A For the customers in Canada Table of Contents Appendix Installation and Connections Typical CCD Phenomena Precautions Visca camera protocol supported FeaturesBuilt-in interface card slot Long-distance image transmission and pan/tilt/zoom control External video sync function Supplied Components and AccessoriesMounted circuit board using lead-free solder System Components BRU-H700 HD Optical Multiplex Unit Remote commanderRM-BR300 Remote Control Unit Optional Products HFBK-TS1 HDV Interface Board Video Switcher commercially availableHFBK-SD1 SD Interface Board HFBK-HD1 HD Interface Board System configuration System ConfigurationThis system allows you Overview System Configuration Operating a BRC-H700 Camera from a Long Distance Operating Multiple BRC-H700 Cameras from a Long Distance CCFC-M100HG CCFC-M100HG BRBK-H700 HD Transmitting Audio Signals Using the BRU-H700 HFBK-TS1 HDV HD video monitor Microphone Rear Location and Function of PartsCamera Front Bottom Setting of the Bottom switches Remote Commander supplied Mode button RM-BR300 Remote Control Unit not suppliedInstalling batteries Lock button and indicator When the menu of the camera is displayed When the menu of the camera is not displayed TALLY/CONTACT connector Mode selectorVisca RS-232C connector Visca RS-422 connector BRU-H700 HD Optical Multiplex Unit not supplied HFBK-HD1 HD Interface Board not supplied HFBK-SD1 SD Interface Board not supplied HFBK-TS1 HDV Interface Board not supplied HFBK-XG1 XGA Interface Board not suppliedBRBK-H700 HD Optical Multiplex Card not supplied About On-Screen Menus Setting MenusMain Menu To return to the normal display Menu Operation Using the Supplied Remote CommanderOperation Through Menus To return to the main menu 4,5 Back Light Exposure MenuSpot Light Color Menu Using the ND FilterWhite Balance white balance mode When ONE Push is selected Picture Menu Color BAR Black and white modeMode focus mode Focus Menu Ramp Curve Setting range of PAN LEFT/PAN RightSetting range of Tilt DOWN/TILT UP PAN Tilt Zoom Menu Analog OUT System MenuSync Master ADD Sync Status MenuDown Converter Menu SUB OUT1 Sync HD-SDI MenuPC-OUTPUT Menu Sync VD HDV Menu Audio Delay Pan/Tilt and Zoom Operation Turning on the PowerPanning and Tilting Zooming Operating Multiple Cameras with the Remote CommanderIf the Standby lamp of the camera flashes To focus the camera on a subject automatically Adjusting the CameraFocusing on a Subject Shooting with Back Lighting To cancel the preset memory To recall the stored settings Operating Multiple Cameras To illuminate the panel of the Remote Control UnitTo assign camera addresses automatically To assign camera addresses manually Direction REV 1STD PAN-TILT Reset Turn the dial on the upper part of the joystick To adjust the white balance manually Adjusting the White BalanceOne-push auto focusing during manual focus adjustment To adjust the white balance automatically Functions of the Value and Bright controls Adjusting the BrightnessFunctions of the R and B controls To select positions 9 to Storing Camera Settings Setting the Speed of the Camera Moving to a Preset Position To remove the cable cover InstallationRemoving/Attaching the Cable Cover Attaching an Interface Board To attach the camera to a tripod Installing the CameraTo install the camera on a desk To remove the interface board Before installation Installing the Camera on the CeilingInstallation example Attachment materials Ceiling Hole Ceiling bracket B Connections Connecting to an AC OutletTo remove the camera Connecting the RM-BR300 Remote Control Unit Visca Connecting a Device Equipped with Visca RS-422 Connector Monitor HFBK-SD1 SD Connecting a VTR Equipped with HD-SDI Input Connectors Connecting a VTR Equipped with SDI Input Connector Connecting the BRU-H700 HD Optical Multiplex Unit Connecting a Computer Cable Second BRC Connecting a Video Switcher To connect multiple cameras to the HD sync signal generator Connecting a Sync Signal GeneratorTo connect a single camera Sync To connect multiple cameras to the SD sync signal generator Messages for the BRC-H700 camera Indicators on the BRC-H700 cameraError messages for the BRU-H700 HD Optical Multiplex Unit List of Messages Symptom Cause Remedy Troubleshooting Symptom Cause Remedy Speed Menu Configuration STD RGB Presetting menu items Presetting Items SUB OUT ADD Sync IMG Size System SpecificationsInput/output connectors Supplied accessories Top Side DimensionsBRC-H700 Video Camera Ceiling Bracket B RM-BR300 Remote Control Unit Top Front Side BRU-H700 HD Optical Multiplex Unit Top Pin Assignments Visca RS-422 connector connector plug 9-pinVisca RS-232C in connector mini-DIN 8-pin, female Visca RS-232C OUT connector mini DIN 8-pin, female BRU-H700 HD Optical Multiplex Unit optional RM-BR300 Remote Control Unit optional Female Visca RS-232C OUT connector mini DIN 8-pinPin Third to Seventh BRC-H700 or BRU-H700 Wiring Diagram of Visca RS-422 ConnectionSecond BRC-H700 or BRU-H700 To remove the connector plug Using the Visca RS-422 Connector Plug