Scsi Interface, Introduction, Supported Messages | Sony SDX-1100V/R

5.SCSI Interface

5. SCSI Interface

5.1.Introduction

The Sony SDX-1100V uses the SCSI interface to connect to the host system. The Small Computer System Interface (SCSI) is an industry standard interface, approved by the American National Standards Institute (ANSI). It is recommended that this document be used along with the ANSI standard document. The ANSI specification defines the interface in general while this document describes the specific implementation for this unit. The SCSI documents, listed in detail in clause 1.2, offer the information required to integrate this unit with SCSI-compatible computer systems. This clause includes four sub-clauses:

•Introduction

•SCSI Bus Operation

•SCSI Messages

•SCSI Status

Note: The details of each SCSI Command are covered in Section 6.

The Introduction provides general, high-level information. For the hardware description and the installation requirements, see Section 2.The SCSI protocol supported by the unit are covered in the Bus Operation, Message, and Status clauses.

5.1.1.Overview of the SCSI Interface

The SCSI implementation provides the unit with a standard set of features and functions. These include:

•Asynchronous and Synchronous communication modes

•Single-ended / Differential Configurations

•Full implementation of Mandatory commands

•Implementation of most sequential non-Mandatory commands

•Ultra160 SCSI Interface

i.Cyclic Redundancy Check (CRC)

ii.Double Transition Clocking (DT)

iii.Domain Validation

5.1.2.Supported Messages

The following messages are supported: (alphabetic order)

*Abort

*Bus Device Reset

*Command Complete

*Disconnect

*Extended Message - Synchronous Data Transfer Request

*Extended Message - Wide Data Transfer Request

*Extended Message - Parallel Protocol Request

*Identify (w/ & w/o disconnect)

*Ignore Wide Residue

*Initiator Detected Error

*Message Parity Error

*Message Reject

*No Operation

*Restore Pointers

*Save Data Pointer

For implementation details on these messages, see clause 5.3.

SONY AIT-5 drive SDX-1100V series Ver.1.0

5-1

Image 41

Sony SDX-1100V/R manual Introduction, Overview of the Scsi Interface, Supported Messages

Contents

SDX-1100V SDX-1100V/R 5.25Model Sony New Zealand Introduction Installation Command Specification 11-1 10-112-1 13-1 Appendix G CD-ROM Device Emulation for Disaster Recovery This page intentionally left blank Features of the Drive About this Product Specification ManualIntroduction Introducing the Sony AIT Technology Introduction Reference How to get ECMA-329 Standard Document This page intentionally left blank Specifications Dimensions Specifications Mounting Holes 2b SDX-1100V/R Mounting Holes Connectors WeightEnvironmental Specifications Temperature and Humidity Range Suspended Particulate AltitudeVibration Shock Data Capacity Performance Specification Initialize Time Data transfer RateLoad Time Unload Time Long Erase Time Error RateDefinition of Failure Mean Time Between Failures Conditions of Acceptability SafetyInstallation Requirements Power Requirements Data Compression Installation Guide Installation DIP SW Mode Termination Power SwitchScsi ID Number Jumper Scsi ID3 ID2 ID1 ID0 Data Compression on Switch Parity Disable JumperPower Connector Scsi 68 pin Connector Ground BSY +BSY ACK +ACK Ground Diffsens Termpwr Reserved+RST MSG +MSG SEL +SEL Ground Termpwr Reserved GroundGround BSY ACK MSG Ground SEL REQ Attaching the Dust Cover Attaching and Removing the Dust Cover Removing the Dust Cover This page intentionally left blank Operation Tape Motion Cleaning RequestSummary of LED Indications Meaning of each LED indications Replace Tape Hard Reset Hole Operator Action Powering up the DriveInserting Cassettes Removing Cassettes Unload Sequence Power-Fail or Scsi Reset HandlingInternal Function Load Sequence Kernel Test Diagnostic and Normal Status DisplaysFront Panel Test Tape Alert Tape Motion Cleaning Request Replace TapeTape Format Normal LED indications Tape drive will not accept a tape cartridge Maintenance, Troubleshooting and Service Head CleaningTroubleshooting Guide Tape is in the drive and will not eject Photo 2 The Initial Position of the Threading Mechanism Tape guide surface Cartridge Detail a Packaging for Return to Sony Clearance for Service This page intentionally left blank Introduction Scsi InterfaceOverview of the Scsi Interface Supported Messages Supported Scsi Commands Command Name Operation Code Supported Commands Disconnect Scsi Bus Operation Typical Scsi Operation Identify Message SpecificationMessage Descriptions Code Direction Extended Message 01h Command Complete 00hParallel Protocol Request Transfer Period Factor Reserved REQ/ACK Offset Byte Value Description Synchronous Data Transfer Request Responding Device Sdtr response Implied Agreement Synchronous Data Transfer Rates Byte Value Wide Data Transfer Request Disconnect 04h Restore Pointers 03hSave Data Pointer 02h Message Parity Error 09h Initiator Detected Error 05hAbort 06h Message Reject 07h Identify 80h-FFh BUS Device Reset 0ChIgnore Wide Residue 23h Ignore Wide Residue Message Byte Value Status Specification Scsi Interface This page intentionally left blank Scsi Commands and Page Index Command SpecificationPara Scsi Command OP Code Load /UNLOAD Reserved Immed Long Control Erase 19hBit Byte Operation Bit Byte Operation Code 12h Reserved CmdDT Inquiry 12hEvpd Or Operation Code Reserved Allocation Length Control MSB Bit ByteSony LSB MSB LSB MSB Length 0Ah Product Serial number in Ascii Vital Product Data Length 08h Product Revision Level Not Available Length 32h Reserved 00h Code set 02h Identifier type 01hIdentifier length 08h Ieee EUI-64 Code Command support data Immed LOAD/UNLOAD 1BhHold Reten Load Hold Reten Load Action Load Unload Command Parameter Combinations LSB Locate 2BhMSB PCR LOG Select 4ChParameter List Length Control field values Value Description MIC Variable Length Information Parameter Codes Description CodesCode Description Bit Byte Operation Code 4Dh Reserved PPC LOG Sense 4DhReserved Parameter Pointer Control field values Value Type of Parameter Values Supported Log Pages Log Page Descriptor Lbin Log Parameter Descriptor Threshold Met Criteria 12 Threshold Met criteriaTMC Summary List of Supported Pages 00h Write and Read Error Counters Pages 02h or 03h Last N Error Events List 07h Tape Alert Log Page 2Eh Recommended application client message Probable cause Tape Alert Log Page Parameter Codes Flag Recommended application client message Probably cause Code Flag Restart the operation Is not mechanically 22 Tape Log Bit Byte Reserved Code 30h Tape Log Page 30h Sony UniqueParameter Code Lbin Parameter Length m Parameter Value Tape Capacity Log Page 31h Sony Unique Length 00 20h when AIT Bit =0 04 00h when AIT bit =124 Tape Capacity Log Bit Byte Code 31h Reserved 25 Capacity Descriptors Bit Byte Drive Usage Log Page 33h Sony Unique Read and Write Frame Error Counter Page 34h & 35h Parameter Code Length Default Cumulative Default Threshold TSD ETC TMC Lbin 34 Data Compression Transfer Log Bit Byte Reserved Code 39h Data Compression Transfer Log Page 39h Sony UniqueLength 58h Parameter Code n Length n+1 AIT Log Page 3Ch Sony Unique35 AIT Log Bit Byte Code 3Ch Reserved LOG Sense 36 MIC Fixed Length Information Bit Byte MIC Fixed Length Information Page 3Dh Sony Unique Prth Ponej AITABS MSB Current Amount of Data Written LSB LOG Sense ABS MIC Variable Length Information Page 3Eh Sony Unique LOG Sense Mode Select 6 CDB Format Bit Byte Operation Mode SELECT6/10 15h and 55h Block Length Number of Blocks 00 00 00hLongls Reserved Block Descriptor Length 08h Density Code Mode Fixed Bit in Read, Write Block Length 40 Sequential-Access Density Codes Code ValueCommand Sequence Error 41 Mode Select Page Header Bit Byte 42 Supported Mode Select Page Codes Description Dtdc Disconnect-Reconnect Page 02h Autoload Mode Control Mode Page 0Ah44 Autoload Mode field Code 0Ah Length 0Ah Reserved DCE Data Compression Control Page 0FhDDE RED 00h Reserved 46 Device Configuration Bit Byte Device Configuration Page 10hCAP REW Mode Select IDP Psum Medium Partitions Parameter Page 11h Mode Select Informational Exceptions Control Page 1Ch Timer 00 00 00 00hMrie MSB Report Count/Test Flag Number AIT Device Configuration Page 31h Mode Select DBD Mode Sense 6/10 1Ah and 5AhPCF Llbaa DBD Length 08h Density Code 33h 54 Supported Mode Sense Page Codes Description Mode Sense MSB Generation LSB Service ActionPersistent Reserve in 5Eh Reservation Key Reservation descriptorSCOPE-SPECIFIC Address Scope Type Name Description 60 Persistent Reservation Scope Codes61 Persistent Reservation Type Codes Code Name Description Persistent Reserve OUT 5Fh Service Action Scope TypeBit Byte Operation Code 5Fh Reserved Parameter List Length 18h Address Type Service Action SCOPE- Specific Reservation KEY Reserved Prevent Control Prevent Allow Medium Removal 1Eh Sili Read 08hFixed Transfer Length Read Service Action Reserved Volume Number0 Partition Number0 65 Read Attribute command Bit Byte Operation Code 8ChRead Attribute 8Ch First Attribute ID 66 Read Attribute service action codes Code Name Description Attribute Values service action Available Data n-3 Attribute List service actionAttribute Attribute Identifier MSB LSB Volume List service action Partition List service actionVolume Number First Volume Number Number of Volumes Available 71 Read Block Limits Data Bit Byte Read Block Limits 05hMaximum Block Length Limit 80 00 00h Minimum Block Length Limit 00 04h 72 Read Buffer Mode values Description Bit Bite Operation Code 3Ch Reserved ModeRead Buffer 3Ch Buffer Offset Available Length 73 Read Buffer Header Bit Byte Reserved74 Buffer ID values Description Offset 75 Read Buffer Descriptor Bit Byte Reserved MSB Buffer Capacity LSB 76 Echo Buffer descriptor Bit Byte Reserved Ebos Tclp Long Read Position 34hBOP EOP BPU MPU BPU 78 Read Position Data Format, long form Bit ByteBlock Number File Number Length 00 02h Receive Diagnostic Results 1ChSupported Page Code 00h Supported Page Code 81h Length 00 05h Bit Byte Reset Time Reserved Error Set Parameter List Length Control Release 6/10 17h and 57h Invalid Field in CDB Media Report Density Support 44h83 Report Density Support header Bit Byte Available Density Support Length MSB Bits PER MM 119 120 116127 128 Report Device Identifier A3h Service Action Must be 05h 86 LUN reporting parameter list format Bit Byte Report Luns A0hLUN List Length 00 00 08h LUN List Reserved Allocation Length 1Ch Control Request Sense 03h Sksv EOM ILICLN MEW SKSV0 SKSV1BPV Bytes Description Key Recovered Error90 Sense Key Descriptions Cleaning Failure Append Position ErrorCartridge Fault END-OF-PARTITION / Medium Detected Saving Parameters not Supported Parameter Value Invalid Medium Auxiliary Memory Accesible Power ON, RESET, or BUS Device Reset OccurredNot Ready to Ready TRANSITION, Medium MAY have Changed Initiator Detected Error Message Received Aborted CommandCommand Phase Error Volume Overflow Diagnostic Failure 91：Runtime Error Code Obsolete Reserved Control Reserve 6/10 16h and 56h92 Reserve 6 CDB format Bit Byte Operation MSB Reserved Immed Control Rewind 01h 95 Diagnostic Page Format Bit Byte Code Reserved Send Diagnostic 1DhReserved Self Test UnitOfl Send Diagnostic SET Device Identifier A4h Service Action06h Reserved Parameter List Length Control Reserved Code Space 11hCount 99 Space codes Sense Key EOMASC/ASCQ BOT Check Condition 3A 00 Medium not Present Test Unit Ready 00h04 01 Logical Unit is Becoming Ready 04 00 Logical Unit not Ready Reserved Fixed Write 0Ah Write Attribute 8Dh Volume NumberPartition Number MSB Parameter List Length LSB Parameter Datalength n-3 103 Write Attribute parameter list format Bit Byte 104 Write Buffer Mode Field Description Reserved Mode Buffer ID105 Write Buffer Mode Field Write Buffer 3Bh Write Buffer Number of Filemarks or Setmarks Write Filemarks 10hReserved WSmk Immed Diagnostic Test Drive DiagnosticsPower-on Self Test Overview Send Diagnostic command Individual Test Send Diagnostic command Self Test Diagnostic Test Number Summary Error Code Result a Result B Diagnostic Test Number Receive Diagnostic Result commandSequence Test Main Processor Kernel Test Drive Diagnostics This page intentionally left blank ASC and Ascq Assignments Appendix a ASC & Ascq Alphabetic OrderAlphabetic Order Byte Description Mechanical Positioning Error Logical Unit not READY, Auxiliary Memory not AccessibleMessage Error Mode Parameters Changed Numeric Order Appendix B ASC & Ascq Numeric Order Command Sequence Error Byte Appendix C ASC & Ascq for AIT Sony UniqueASC and Ascq Assignments for AIT drive Sony Unique 10-2 Sony AIT-5 drive SDX-1100V series Ver.1.0 Appendix D Scsi Commands Op Code Order Report Device ID SET Device ID Read Write Attribute Appendix E Medium Auxiliary Memory Attribute MAM Attribute Format Bit Byte Attribute FormatMAM Attribute states Standard Device Type Attributes Attribute Identifier ValuesMAM attribute formats MAM attribute identifier range assignments Device Common Attributes Product Serial Number Device VENDOR/SERIAL Number attribute format Bit ByteVendor Identification Current Amount of Data Written Medium Usage History attribute format Bit ByteCurrent Amount of Data Read Current Read Retries Count Appendix E Medium Auxiliary Memory Attribute Current Write Reties Count Partition Usage History attribute format Bit ByteChange Partition Count Partition Initialize Count 10 Medium Common Attributes Attribute Name #Bytes Format Standard Medium Type Attributes Medium Type Standard Host Type AttributesMedium Type Information 12 Host Common Attributes Value Meaning 13 Text Localisation Identifier 12-12 Sony AIT-5 drive SDX-1100V series Ver.1.0 How to detect a Worm cartridge Write-Protected WP Bit in Mode Sense DataHow to initialize a Worm cartridge Appendix F AIT based Worm system END How to handle the Worm cartridge in the drive Appendix G CD-ROM Device Emulation for Disaster Recovery Reset Handling Mode Sense/Select Page Code 0x3CRead TOC Returned Data 20 bytes