6.Command Specification

 

 

LOG SENSE

 

 

 

 

 

 

Code

Flag

Flag Type

Recommended application client message

Probable cause

1Eh

Hardware A

C

The tape drive has a hardware fault:

The drive has a hardware

 

 

 

 

1.

Eject the tape or magazine.

fault that requires reset to

 

 

 

 

2.

Reset the drive.

recover.

 

 

 

 

3.

Restart the operation.

 

 

1Fh

Hardware B

C

The tape drive has a hardware fault:

The drive has a hardware

 

 

 

 

1.

Turn the tape drive off and then on again.

fault which is not read/write

 

 

 

 

2.

Restart the operation.

related or requires a power

 

 

 

 

3.

If the problem persists, call the tape drive

cycle to recover.

 

 

 

 

supplier helpline.

 

 

 

 

 

 

Check the tape drive user’s manual for device

 

 

 

 

 

 

specific instructions on turning the device power

 

 

 

 

 

 

on and off.

 

 

20h

Interface

W

The tape drive has a problem with the initiator

The drive has identified an

 

 

 

 

interface:

interfacing fault

 

 

 

 

1.

Check the cables and cable connections.

 

 

 

 

 

 

2.

Restart the operation.

 

 

21h

Eject Media

C

The operation has failed:

Error recovery action

 

 

 

 

1.

Eject the tape or magazine.

 

 

 

 

 

 

2.

Insert the tape or magazine again.

 

 

 

 

 

 

3.

Restart the operation.

 

 

22h

Download Fail

W

The firmware download has failed because you

Firmware download failed

 

 

 

 

have tried to use the incorrect firmware for this

 

 

 

 

 

 

tape drive.

 

 

 

 

 

 

Obtain the correct firmware and try again.

 

 

 

 

 

 

 

23h

Drive Humidity

W

Environmental conditions inside the tape drive

Drive humidity limits

 

 

 

 

are outside the specified humidity range

exceeded

 

 

 

 

 

24h

Drive

W

Environmental conditions inside the tape drive

Drive temperature limits

 

 

Temperature

 

are outside the specified temperature range

exceeded

 

 

 

 

 

25h

Drive Voltage

W

The voltage supply to the tape drive is outside

Drive voltage limits exceeded

 

 

 

 

the specified range

 

 

 

 

 

 

 

26h

Predictive

C

A hardware failure of the tape drive is predicted.

Predictive failure of drive

 

 

Failure

 

Call the tape drive supplier helpline.

hardware

27h

Diagnostics

W

The tape drive may have a fault. Check for

The drive may have had a

 

 

Required

 

availability of diagnostic information and run

failure which may be

 

 

 

 

extended diagnostics if applicable.

identified by stored

 

 

 

 

Check the tape drive users manual for

diagnostic information or by

 

 

 

 

instructions on running extended diagnostic

running extended

 

 

 

 

tests and retrieving diagnostic data

diagnostics (e.g. Send

 

 

 

 

 

 

Diagnostic)

28h

Loader

C

The changer mechanism is having difficulty

Loader mechanism is having

 

 

Hardware A

 

communicating with the tape drive:

trouble communicating with

 

 

 

 

1.

Turn the autoloader off then on.

the tape drive

 

 

 

 

2.

Restart the operation.

 

 

 

 

 

 

3.

If problem persists, call the tape drive supplier

 

 

 

 

 

 

helpline.

 

 

29h

Loader Stray

C

A tape has been left in the autoloader by a

Stray tape left in loader after

 

 

Tape

 

previous hardware fault:

previous error recovery

 

 

 

 

1.

Insert an empty magazine to clear the fault.

 

 

 

 

 

 

2.

If the fault does not clear, turn the autoloader

 

 

 

 

 

 

off and then on again.

 

 

 

 

 

 

3.

If the problem persists, call the tape drive

 

 

 

 

 

 

supplier helpline.

 

 

2Ah

Loader

W

There is a problem with the autoloader

Loader mechanism has a

 

 

Hardware B

 

mechanism.

hardware fault

6-22

SONY AIT-5 drive SDX-1100V series Ver.1.0

Page 76
Image 76
Sony SDX-1100V/R manual Restart the operation