Check Network and Installation Type | Speco Technologies & IP-WDRB1

Speco Technologies	IP Camera User’s Manual

3.Basic Setting

3.1.Check Network and Installation Type

This Chapter is for basic setting of THE CAMERA. To install Hardware of the Network Camera, basic understanding of Networking is required. Please refer to Chapter 6 in case knowledge of Network Environment is required. There are 2 ways to install Hardware. One is to install THE CAMERA without IP sharing Device under Cable Modem or Leased Line, the other one is to install THE CAMERA under an IP sharing Device , which is required necessarily under PPPoE environment, and even under Leased Line or Cable Modem. The default IP Address of THE CAMERA is preset to 192.168.1.7 and Subnet Mask to 255.255.255.0 and Gateway to 192.168.1.1 in the factory. This explanation is based upon default value of the factory.

Caution 1 : Check Video before installation, on ‘2. Install and Video Check’.

Caution 2 : In case using IP sharing Device, only Global IP is available.

Caution 3 : THE CAMERA does not support PPPoE. IP Sharing Device is required to connect to THE CAMERA under PPPoE.

Installation without IP sharing device

-> For static IP, refer to ‘Static IP Setup’.

-> For dynamic IP, refer to ’ Dynamic IP Setup’.

Installation with IP sharing device

-> Should set up with Static IP. Refer to ‘Installation with IP Sharing Device’.

19

Image 19

Speco Technologies & IP-WDRB1, IP-INTT5 Check Network and Installation Type, Installation without IP sharing device

Contents

IP Camera User’s Manual Introduction Important Notes Contents Basic USE 118 115 Feature Package Feature Dimensions Dimension and Camera Features ① ③ Intensifier Cameras Not available with IP-T5 Camera Feature III. WDR Camera Install and Check Video Video Check Installation ―2 Web Browser Input User ID, Password, Rights User Password ―4 User login ―5 ActiveX Download Basic Setting Installation without IP sharing device Check Network and Installation TypeInstallation with IP sharing device ―1 Main Page of the Camera Network Camera Static IP Setup ―3 Administrator’s Pic 3―5 IP Change ―4 Network Setting Check Dynamic IP Setup ―7 Network Setting ―8 Initial Page of the Camera Installation with IP Sharing Device Router ―9 Network Setting ―10 IP Change ―13 Main Page of the Camera Page Expert Setting Expert Setting ―2 Administrator’s Title Setting General Setting User Registration Administrator’s ID and Password Change User List and Delete Skip Login Automatic Monitoring Set Download Route of Plug-in Type ActiveX Time Zone Setting Select Language Network Setting Video Setting Video Setting Alarm Setting Color SettingAlarm Event Setting ―18 Alarm Setting Alarm Event Test DIO Setting support for IP-INTT5/T5, IP-SD10X Motion Area Setup 20 Camera Setting Camera Settingsupport for IP-SD10X Firmware Update Homepage Update ―22 Firmware Update Remote Upgrade ―24 Firmware Download ―27 Upgrade Server Connection Error System Re-booting Reset Button Factory ResetReset of Factory default Basic Use Use of Web Viewer Basic Use Flickering on Screen Alarm Sound Definition of Web Viewer Key Board Same function as Function Use of OSD Not available with IP-T5 Speco Technologies Speed Dome Camera IP-SD10X WDR Camera IP-WDRB1 F T Downsetup OSD Menu Setting Operating Camera OSD Menu Intensifier Cameras Select the desired feature using the UP or Down button Speco Technologies IP Camera User’s Manual Brightness Speco Technologies IP Camera User’s Manual Speco Technologies IP Camera User’s Manual Speco Technologies IP Camera User’s Manual OFF LOW Middle High OFF on White Balance White BAL Page Speco Technologies IP Camera User’s Manual Intensifier Next Speco Technologies IP Camera User’s Manual Color Sync Privacy Reverse Detail Default Main Menu Operating WDR Camera OSD Menu IP-WDRB1OSD Menu Control OSD Menu Enter / Exit Lens Exit Menu Operating Camera OSD Menu IP-SD10X Dome SET Manual Speed Default SettingDome SET Recover Dome SET Camera ID Dome SET Language Dome SET AlarmDome SET Next page Password Dome SET Zoom Speed Dome SET Next page OSD Display Confirmed Cancelled SDM100 Samsung 10X Zoom Camera Module Dome SET Next page System StatusDome SET Next page Initialization Tour Clear Are YOU SURE? YES no Camera SET Mirror Dome SET Next page Save and ExitDome SET Next page Exit Camera SET Flickerless Camera SET D Zoom Camera SET WB ModeCamera SET D/N Mode Camera SET Aperture Camera SET Exit Camera SET DSS Mode Digital Slow ShutterPreset Preset no Preset Preset ID Focus FAR Preset PAN XXX.X TiltPreset Save Preset Exit Auto Scan Save and Exit Auto Scan EndlessAuto Scan Speed Auto Scan Dwell Time Tour SET Tour Step Tour SET Preset noTour SET Tour no Tour SET Tour Title Tour SET Exit Privacy SET ACTIONMOVE/ADJUSTTour SET Speed Tour SET Save Privacy SET Exit Privacy SET SavePattern SET Patt no Pattern SET Data Fill Pattern SET Patt TitleZoom Tele Zoom Wide Alaram SET Save Alaram SET Alarm noAlaram SET Alarm Input Alaram SET Alarm ACT Sector SET Sector ID Sector SET Sector noSector SET Sector Start Sector SET Save Sector SET Sector ENDSector SET Exit ID SETTING1-ON, 0-OFF110 DIP SW Setting Protocol ―2 IP Find Use of IP Setting Utility ―4 IP Check ―6 Service Server Use of Service Server ―7 User Login ―9 User Registration Camera Registration ―11 Service Server Log-in Succeeded ―13 Camera Registration List of Camera ―14 Camera List Change of User’s Information ―16 Alarm Log List ―17 Change User’s Information Search Camera WAP2.0 Html See and Control of Still Image in Mobile or PDA ―21 Input User ID ―24 Pan/Tilt/Zoom Control ―25 PDA Log-in PDAWinCE Refer the NVR User’s Manual in the CD-ROM Required Specification of PC and OSUse of NVR Program Supported O/S Network Environment Network Environment Page Appendix Appendix Appendix a Basic Setting Table IP-INTB1 / INTB2 Appendix B Specification of Products IP-INTD3 / INTD4 IP-INTT5 122 IP-WDRB1 124 Appendix C To solve problem