Tektronix OA 5000 Power Up

Appendix G: Product Verification

Appendices

A --- 2 2

Table4-1: Equipment Required for Performance Verification

Description RecommendationMinimum Use Specifications

OA 5022,

Optical input

and output fiber

1 to 5 m long, 62.5/125 m, FC/PC

to FC/PC2

Tek t r on i x

174-2322-00

OA 5032,

Optical input

and output fiber

1 to 5 m long, 100/140 m, FC/PC

to FC/PC2

FC/FC adapter Femaleto female Tek t r on i x

131-6252-00

1Lasershou ldha veshor tcoher ence length (<1 m if possible) and multiple longitudinal

modesto minimize effectsof polarization and reflection. If a DFB or tunable laser is used, it

shouldhave a coheren ce control feature and optionally a polarization scrambler.

2Thefiber specificationsassume that adapters on the testequipment and the DUT (device

undertest) are F C/PC. Alternativeadapters ca n be used with appropriate changes in the

fibercon nectors.

Step 1: Insert the OA 5000 into a powered-down TektronixTM 5000

series Mainframe power supply.

HMake certain that the OA 5000 is securelylatched into the main-

frame.

Step 2: Turn the TM 5000 mainframe power on (via mainframe’spower

switch)

Step 3: A few seconds are required after mainframe power-up before

the OA 5000 displaysbecome lit.

HOnce the displaysbecome active, all LEDs and digital segments will

be lit for a couple of seconds; any segment which does not light up

during this time iseither defective, burnt out, or is not connected.

HThis test can be invoked anytimeafter power up by pushing and

holding the ADDR(SET)button.

Step 4: The wavelength, attenuation, and display mode will power-up at

whatever values existed before the previouspower-down; if the instru-

ment is being powered on forthe first time the settings will be at their

factory default values(see manual for these default values).

Power Up

Contents

Main Page WARRANTY Page ECDeclarationofConformity Page Welcome Page Contents A Quick Tour User Reference Programming Appendices Page List of Figures List of Tables Safety Symbols and Terms Specific Precautions Page Page Page Page Installation CAUTION Removing the OA 5000 A Quick Tour Preset the OA 5000 Storing and Recalling Settings Setting a Reference Value Settings at Power Up Page Page Operator Overview The User Reference Section Operator Overview 2 --- 2 Figure 2-1: OA 5002 Front Panel User Reference Enabling/Disabling Attenuation WARNING Page Setting Attenuation Levels Specifying the Wavele ngth Setting the Attenuation Level Page Page Setting the GPIB Address Page Setting the Reference Level Measuring Insertion Loss Approximating Signal Power Page Storing and Recalling Attenuation Levels Page Page Page Setting Up the Instrument Controllers Using the GPIB Interface GPIB Requirements Setting the GPIB Address Page Command Syntax Clearing the OA 5000 ATT:DB 10 Command and Query Structure Commands Queries Headers in QueryResponses Command Entry Abbreviating Commands Concatenating Commands Message Terminators Argument Types Block Arguments Numeric Arguments Syntax Diagrams Page Commands Common Commands and Queries Device Commands and Queries ADJusting? (Query Only) ALLev? (Query Only) Page BLRN *CAL? (Query Only) *CLS (No Query Form) DESE DISable DISPlay *ESE *ESR? (Query Only) EVEnt? (Query Only) EVMSG? (Query Only) EVQty? (Query Only) FACTORY (No Query Form) HEADer *IDN? (Query Only) *LRN?orSET? *OPC *PSC RECall (No Query Form) REFerence *RST (No Query Form) *SRE *STB? (Query Only) STORe (Store Attenuation) *TST? (Query Only) VERBOSE *WAI (No Query Form) WAVelength Status and Events Registers Status Registers The Standard Event Status Register (SESR) The Status Byte Register (SBR) Enable Registers The Device Event Status Enable Register (DESER) The Event Status Enable Register (ESER) The Service Request Enable Register (SRER) The Enable Registers and the *PSC Command The Output Queue The Event Queue Queues Event Handling Sequence Status and Events Conflicts 3 --- 4 0 Programming Messages Page Page Page Page Page Appendix A: Accessories Standard Accessories Optional Accessories Page Appendix B: Specifications Page Page Page Appendix C: Interface Specifications Interface Messages Page GPIB Function Subsets Page Appendix D: Using the *OPC Query/Command Page Appendix E: Packing for Shipment Page Appendix F: Maintenance Cleaning the Optical Ports Page Changing the Optical Port Connectors Page Page Page Appendix G: Product Verification Equipment List Power Up Display Modes GPIB Address Setting Attenuation Range Shutter Attenuation and the DISABLE button 1310 nm: Page 1550 nm: 850 nm (except OA 5002): Page Appendix H: Replaceable Parts Item Names Parts Ordering Information Using the Replaceable Parts List Indentation System Abbreviations Page AppendixH: Replaceable Parts A --- 3 4 Appendices CROSS INDEX --- MFR. CODE NUMBER TO MANUFACTURER AppendixH: Replaceable Parts OA 5000 Series User Manual A --- 3 5 Page Page Page Index A B C D E F G H N O P Q R T U V W