Tektronix OA 5000 850 nm (except OA 5002):

Appendix G: Product Verification

OA 5000 Series User Manual A --- 2 9

Table4-3: Attenuation Accuracy at 1550 nm

OA 5002 OA 5012 / OA 5022 /

OA 5032

Attenuation

setting (dB)

Tolerance Limits (dB) Tolerance Limits (dB)

10 ---10.15 to ---9.85 ---10.20 to ---9.80

20 ---20.15 to ---19.85 ---20.20 to ---19.80

30 ---30.15 to ---29.85 ---30.20 to ---29.80

40 ---40.15 to ---39.85 ---40.20 to ---39.80

50 ---50.20 to ---49.80 ---50.20 to ---49.80

Step 1: Disconnectthe fibers from the OA 5000, 1550 nm laser,and

long wavelength sensor.Connect the 850 nm laser to the input fiber and

the short wavelength sensor to the outputfiber. Connect the fibers

together using an FC/FC adapter.Set the laser to CW (unmodulated)

mode, and set the laser power level (ifadj ustable)to maximum, but not

more than 2 mW.Turn on the laser.

Step 2: Atthe power meter, select the short wavelength sensor.Set the

wavelength displays ofthe OA 5000 and the power meter to the actual

wavelength (not the nominalw avelength)of the laser, within ±1 nm.

Step 3: Setthe power meter to W (watts) mode. The reading should be

at least 400 W.Set the power meter to dB relative (dB key) mode, and

set the dB reference (Disp-->Ref). The power meter should read 0.0 dB

±0.1 dB.

Step 4: Disconnectthe fibers from the FC/FC adapter,and connect

them to the OA 5000.

Step 5: Setthe OA 5000 attenuation to 0 dB, and the DISABLEbutton

to off (unlit).

Step 6: Thepower meter reading is the insertion loss of the OA 5000.

Check that the power meter reading is ---4.0dB or higher (more posi-

tive).

NOTE

During theremaining steps, do not disturbthe connections and

fibers.

850 nm (exceptOA 5002):

Insertion Loss,

Attenuation

Accuracy, and

Repeatability

Contents

Main Page WARRANTY Page ECDeclarationofConformity Page Welcome Page Contents A Quick Tour User Reference Programming Appendices Page List of Figures List of Tables Safety Symbols and Terms Specific Precautions Page Page Page Page Installation CAUTION Removing the OA 5000 A Quick Tour Preset the OA 5000 Storing and Recalling Settings Setting a Reference Value Settings at Power Up Page Page Operator Overview The User Reference Section Operator Overview 2 --- 2 Figure 2-1: OA 5002 Front Panel User Reference Enabling/Disabling Attenuation WARNING Page Setting Attenuation Levels Specifying the Wavele ngth Setting the Attenuation Level Page Page Setting the GPIB Address Page Setting the Reference Level Measuring Insertion Loss Approximating Signal Power Page Storing and Recalling Attenuation Levels Page Page Page Setting Up the Instrument Controllers Using the GPIB Interface GPIB Requirements Setting the GPIB Address Page Command Syntax Clearing the OA 5000 ATT:DB 10 Command and Query Structure Commands Queries Headers in QueryResponses Command Entry Abbreviating Commands Concatenating Commands Message Terminators Argument Types Block Arguments Numeric Arguments Syntax Diagrams Page Commands Common Commands and Queries Device Commands and Queries ADJusting? (Query Only) ALLev? (Query Only) Page BLRN *CAL? (Query Only) *CLS (No Query Form) DESE DISable DISPlay *ESE *ESR? (Query Only) EVEnt? (Query Only) EVMSG? (Query Only) EVQty? (Query Only) FACTORY (No Query Form) HEADer *IDN? (Query Only) *LRN?orSET? *OPC *PSC RECall (No Query Form) REFerence *RST (No Query Form) *SRE *STB? (Query Only) STORe (Store Attenuation) *TST? (Query Only) VERBOSE *WAI (No Query Form) WAVelength Status and Events Registers Status Registers The Standard Event Status Register (SESR) The Status Byte Register (SBR) Enable Registers The Device Event Status Enable Register (DESER) The Event Status Enable Register (ESER) The Service Request Enable Register (SRER) The Enable Registers and the *PSC Command The Output Queue The Event Queue Queues Event Handling Sequence Status and Events Conflicts 3 --- 4 0 Programming Messages Page Page Page Page Page Appendix A: Accessories Standard Accessories Optional Accessories Page Appendix B: Specifications Page Page Page Appendix C: Interface Specifications Interface Messages Page GPIB Function Subsets Page Appendix D: Using the *OPC Query/Command Page Appendix E: Packing for Shipment Page Appendix F: Maintenance Cleaning the Optical Ports Page Changing the Optical Port Connectors Page Page Page Appendix G: Product Verification Equipment List Power Up Display Modes GPIB Address Setting Attenuation Range Shutter Attenuation and the DISABLE button 1310 nm: Page 1550 nm: 850 nm (except OA 5002): Page Appendix H: Replaceable Parts Item Names Parts Ordering Information Using the Replaceable Parts List Indentation System Abbreviations Page AppendixH: Replaceable Parts A --- 3 4 Appendices CROSS INDEX --- MFR. CODE NUMBER TO MANUFACTURER AppendixH: Replaceable Parts OA 5000 Series User Manual A --- 3 5 Page Page Page Index A B C D E F G H N O P Q R T U V W