Manuals / Brands / TV and Video / TV Cables / Tektronix / TV and Video / TV Cables

Tektronix OA 5000 Shutter Attenuation and the DISABLE button

1 134

Download 134 pages, 1.07 Mb

Appendix G: Product Verification

OA 5000 Series User Manual A --- 2 5

Step 6: Enter the Wavelength set modefor the OA 5000 by pushing the

WAVELENGTH button so that the top display reads “SEt”.

Step 7: Using the knobs, adjust the wavelength to read 1600 nm.

Step 8: Exit the WavelengthSet mode by pushing the WAVELE NGTH

button again; the instrumentw illrequire a second to prepare the new

calibration tables (as indicated by the ATT AD J briefly lighting up).

Step 9: Adjust the OA 5000 such that the display modeis showing

attenuation in dB with the ATTindicator lit and the ---REF indicator not lit.

Step 10: Using the knobs, increase the level ofattenuation (turn the

coarse knob clockwise); keep increasingthe level until the value reach-

es a maximum level and nolonger increases. This value should exceed

50.00 dB.

Step 1: Set the optical power meter as follows(operating instructions

are for HP8153A):

HSelect the long wavelength power sensor.

HWavelength:actual wavelength (±1 nm) of 1310 nm laser

HAveraging:1 s

Togglethe Mode key to display PARA M, and then press the Param

key to display T and set T to 1 s.

HDisplayed units:W (w atts)

Step 2: Cover the sensor input and zerothe power meter.

Step 3: Connect the 1310 nm laser to the OA5000 input using the input

fiber specified inthe equipment table.

Step 4: Connect the OA 5000 output tothe sensor using the output

fiber specified inthe equipment table.

NOTE

For the OA 5012, OA 5022, and OA 5032 the input fiber may have a

smaller core diameter than the one specified, as lo ng as the laser

can couple into the fiber. For these models, the output fib er may

have a larger core diameter than the one specified, up to 1 00 m.

Step 5: Set the OA 5000:

HWavelength:actual wavelength (±1 nm) of 1310 nm laser

HAttenuation: 0 dB

HDisable: off (unlit)

Shutter Attenuationand the DISABLEbutton

Contents

Main Page WARRANTY Page ECDeclarationofConformity Page Welcome Page Contents A Quick Tour User Reference Programming Appendices Page List of Figures List of Tables Safety Symbols and Terms Specific Precautions Page Page Page Page Installation CAUTION Removing the OA 5000 A Quick Tour Preset the OA 5000 Storing and Recalling Settings Setting a Reference Value Settings at Power Up Page Page Operator Overview The User Reference Section Operator Overview 2 --- 2 Figure 2-1: OA 5002 Front Panel User Reference Enabling/Disabling Attenuation WARNING Page Setting Attenuation Levels Specifying the Wavele ngth Setting the Attenuation Level Page Page Setting the GPIB Address Page Setting the Reference Level Measuring Insertion Loss Approximating Signal Power Page Storing and Recalling Attenuation Levels Page Page Page Setting Up the Instrument Controllers Using the GPIB Interface GPIB Requirements Setting the GPIB Address Page Command Syntax Clearing the OA 5000 ATT:DB 10 Command and Query Structure Commands Queries Headers in QueryResponses Command Entry Abbreviating Commands Concatenating Commands Message Terminators Argument Types Block Arguments Numeric Arguments Syntax Diagrams Page Commands Common Commands and Queries Device Commands and Queries ADJusting? (Query Only) ALLev? (Query Only) Page BLRN *CAL? (Query Only) *CLS (No Query Form) DESE DISable DISPlay *ESE *ESR? (Query Only) EVEnt? (Query Only) EVMSG? (Query Only) EVQty? (Query Only) FACTORY (No Query Form) HEADer *IDN? (Query Only) *LRN?orSET? *OPC *PSC RECall (No Query Form) REFerence *RST (No Query Form) *SRE *STB? (Query Only) STORe (Store Attenuation) *TST? (Query Only) VERBOSE *WAI (No Query Form) WAVelength Status and Events Registers Status Registers The Standard Event Status Register (SESR) The Status Byte Register (SBR) Enable Registers The Device Event Status Enable Register (DESER) The Event Status Enable Register (ESER) The Service Request Enable Register (SRER) The Enable Registers and the *PSC Command The Output Queue The Event Queue Queues Event Handling Sequence Status and Events Conflicts 3 --- 4 0 Programming Messages Page Page Page Page Page Appendix A: Accessories Standard Accessories Optional Accessories Page Appendix B: Specifications Page Page Page Appendix C: Interface Specifications Interface Messages Page GPIB Function Subsets Page Appendix D: Using the *OPC Query/Command Page Appendix E: Packing for Shipment Page Appendix F: Maintenance Cleaning the Optical Ports Page Changing the Optical Port Connectors Page Page Page Appendix G: Product Verification Equipment List Power Up Display Modes GPIB Address Setting Attenuation Range Shutter Attenuation and the DISABLE button 1310 nm: Page 1550 nm: 850 nm (except OA 5002): Page Appendix H: Replaceable Parts Item Names Parts Ordering Information Using the Replaceable Parts List Indentation System Abbreviations Page AppendixH: Replaceable Parts A --- 3 4 Appendices CROSS INDEX --- MFR. CODE NUMBER TO MANUFACTURER AppendixH: Replaceable Parts OA 5000 Series User Manual A --- 3 5 Page Page Page Index A B C D E F G H N O P Q R T U V W