Tektronix OA 5000 Setting Attenuation Levels

OA 5000 Series User Manual 2 --- 5

Setting Attenuation Levels

Because the OA 5000 automaticallyadjusts the attenuator to correct for

different wavelengths, it isimportant, for attenuator accuracy, to correctly

match the displayed wavelength with the wavelength ofthe signal going into

the unit.

Setting attenuation levelson the OA 5000 requires you to perform two

procedures in the followingorder:

1. Specify the wavelength of the signalto be attenuated.

2. Set the level of attenuation.

Refer to Figure 2-3.

DISABLE

MINATT

STORE1 RECALL1

STORE2 RECALL2

REMOTE MODE

SETREF COARSE

FINE

WAVE-

LENGTH

ADDR

(SET)

Thisbutton sets

attenuationto the

minimum

value.

Theseknobs set the

attenuationlevel,

referencelevel,

wavelengthand GPIB

address.

Thisbutton assigns the

ATTENUATIONdisplay to

eitherabsolute units or

units relative to the

referencelevel.

Usethis button to assign the

knobsto adjust the

wavelength.

Figure 2-3: Setting Attenuation Levels

Tospecify the wavelength to be attenuated:

Step 1: Pressthe WAVELENGT H button.

The word SEt will appear inthe attenuation display and the WAVE-

LENGTH button will illuminate.

Specifying the

Wavele ngth

Contents

Main Page WARRANTY Page ECDeclarationofConformity Page Welcome Page Contents A Quick Tour User Reference Programming Appendices Page List of Figures List of Tables Safety Symbols and Terms Specific Precautions Page Page Page Page Installation CAUTION Removing the OA 5000 A Quick Tour Preset the OA 5000 Storing and Recalling Settings Setting a Reference Value Settings at Power Up Page Page Operator Overview The User Reference Section Operator Overview 2 --- 2 Figure 2-1: OA 5002 Front Panel User Reference Enabling/Disabling Attenuation WARNING Page Setting Attenuation Levels Specifying the Wavele ngth Setting the Attenuation Level Page Page Setting the GPIB Address Page Setting the Reference Level Measuring Insertion Loss Approximating Signal Power Page Storing and Recalling Attenuation Levels Page Page Page Setting Up the Instrument Controllers Using the GPIB Interface GPIB Requirements Setting the GPIB Address Page Command Syntax Clearing the OA 5000 ATT:DB 10 Command and Query Structure Commands Queries Headers in QueryResponses Command Entry Abbreviating Commands Concatenating Commands Message Terminators Argument Types Block Arguments Numeric Arguments Syntax Diagrams Page Commands Common Commands and Queries Device Commands and Queries ADJusting? (Query Only) ALLev? (Query Only) Page BLRN *CAL? (Query Only) *CLS (No Query Form) DESE DISable DISPlay *ESE *ESR? (Query Only) EVEnt? (Query Only) EVMSG? (Query Only) EVQty? (Query Only) FACTORY (No Query Form) HEADer *IDN? (Query Only) *LRN?orSET? *OPC *PSC RECall (No Query Form) REFerence *RST (No Query Form) *SRE *STB? (Query Only) STORe (Store Attenuation) *TST? (Query Only) VERBOSE *WAI (No Query Form) WAVelength Status and Events Registers Status Registers The Standard Event Status Register (SESR) The Status Byte Register (SBR) Enable Registers The Device Event Status Enable Register (DESER) The Event Status Enable Register (ESER) The Service Request Enable Register (SRER) The Enable Registers and the *PSC Command The Output Queue The Event Queue Queues Event Handling Sequence Status and Events Conflicts 3 --- 4 0 Programming Messages Page Page Page Page Page Appendix A: Accessories Standard Accessories Optional Accessories Page Appendix B: Specifications Page Page Page Appendix C: Interface Specifications Interface Messages Page GPIB Function Subsets Page Appendix D: Using the *OPC Query/Command Page Appendix E: Packing for Shipment Page Appendix F: Maintenance Cleaning the Optical Ports Page Changing the Optical Port Connectors Page Page Page Appendix G: Product Verification Equipment List Power Up Display Modes GPIB Address Setting Attenuation Range Shutter Attenuation and the DISABLE button 1310 nm: Page 1550 nm: 850 nm (except OA 5002): Page Appendix H: Replaceable Parts Item Names Parts Ordering Information Using the Replaceable Parts List Indentation System Abbreviations Page AppendixH: Replaceable Parts A --- 3 4 Appendices CROSS INDEX --- MFR. CODE NUMBER TO MANUFACTURER AppendixH: Replaceable Parts OA 5000 Series User Manual A --- 3 5 Page Page Page Index A B C D E F G H N O P Q R T U V W